Beef Eater BOKP60WG User manual
AUSTRALIA / NEW ZEALAND
Installation guide PROLINE
OUTDOOR
KITCHEN
BOKP60WG
(includes BM190PWG & BM190PCG)
2
CONTENTS
Dear Customer,
Congratulations and thank you for choosing our Outdoor
Kitchen.
We are sure you will find it a pleasure to use. Before you
use the Outdoor Kitchen, we recommend that you read
through all sections of this instruction manual which provide
the assembly instructions and other relevant care and use
information description
To avoid the risks it is important that the Outdoor Kitchen
and BBQs are both installed correctly and that you read the
safety instructions carefully of this Kitchen and the BBQ to
be installed to avoid misuse and hazards.
We recommend that you keep this instruction booklet for
future reference and pass it on to any future owners.
After unpacking the Outdoor Kitchen, please check it is
not damaged. If in doubt, do not assemble the kitchen but
contact your local customer care centre.
PLEASE NOTE
• The BBQ you install with this kitchen must be installed
and serviced only by a qualified and licenced person.
• This kitchen and installed BBQ is intended for personal,
domestic or household use only, not commercial use.
• This kitchen is only suitable for installation with
BeefEater Proline BBQ and side burner models:
BSL158SA, BSH158SA, BSW318SA, BSL158SB,
BSH158SB & BSW318SB.
• This kitchen must be installed in a location in
accordance with the installation instructions of the BBQ:
• For most BBQs they must be located outdoors in an
area that is not enclosed, however the Proline BBQ
is approved to the commercial catering equipment
standard AS4563:2004 and therefore can be installed in
semi-enclosed areas if the ventilation requirements of
AS/NZS 5601:2013 are met.
• If the Proline BBQ in installed in a semi-enclosed area,
then an LPG cylinder must not be located within the
kitchen cupboard or in the enclosed area. Any LPG
cylinder that supplies gas to the BBQ must be in a
remote location that is not enclosed and piping to the
BBQ installed by a licensed gas fitter in accordance with
the gas installation code.
• For Proline, if the area is not enclosed then an LPG
cylinder of capacity 9kg may be located in the cupboard
in accordance with these instructions – See “WARNING
– If you use an LPG gas cylinder…”
• It is highly recommended that the Proline BBQ is supplied
by NG (Natural Gas), however a LPG conversion kit is
supplied with the BBQ if required, refer to the safety
warnings and instructions supplied with the BBQ.
• An LPG Gas hose connection kit (Part No. A19112301)
suitable to connect the Proline side burner and BBQ
to LPG cylinder can be purchased separately from
BeefEater spare parts.
• This kitchen must be installed and maintained as per the
instructions.
CONTENTSCONGRATULATIONS
Important safety instructions .......................................................3
Product description ......................................................................4
Carcass assembly ........................................................................ 6
Hinge and door assembly .............................................................8
Stone assembly ..........................................................................10
Warranty .....................................................................................11
Please read the user manual carefully and store in a handy
place for later reference.
The symbols you will see in this booklet have these
meanings:
WARNING
WARNING
This symbol indicates information concerning your
personal safety.
WARNING
CAUTION
This symbol indicates information on how to avoid
damaging the appliance.
TIPS & INFORMATION
IMPORTANT
This symbol indicates tips and information about use
of the appliance.
ENVIRONMENTAL TIPS
ENVIRONMENT
This symbol indicates tips and information about
economical and ecological use of the appliance.
IMPORTANT INFORMATION THAT MAY
IMPACT YOUR MANUFACTURER’S WARRANTY
Adherence to the directions for use in this manual
is extremely important for health and safety. Failure
to strictly adhere to the requirements in this manual
may result in personal injury, property damage
and affect your ability to make a claim under the
BeefEater manufacturer’s warranty provided with
your product. Products must be used, installed and
operated in accordance with this manual. You may
not be able to claim on the BeefEater manufacturer’s
warranty in the event that your product fault is due to
failure to adhere this manual.
3SAFETY
Please read the user manual carefully and store in a handy
place for later reference.
TIPS & INFORMATION
IMPORTANT
Important – check for any damages or marks
If you find the kitchen is damaged, you must report it
within 7 days if you wish to claim for damage under
the manufacturer’s warranty. This does not affect your
statutory rights.
ENVIRONMENTAL TIPS
ENVIRONMENT
Information on disposal for users
• Most of the packing materials are recyclable. Please
dispose of those materials through your local recycling
depot or by placing them in appropriate collection
containers.
• If you wish to discard this kitchen, please contact
your local authorities and ask for the correct method
of disposal.
WARNING
WARNING
The BBQ you install in this kitchen must be serviced only by
a qualified licensed person.
Improper installation of the BBQ, adjustment, alteration
or maintenance can cause injury or property damage and
may affect your ability to claim under the manufacturer’s
warranty.
WARNING
WARNING
If you use an LPG cylinder inside the cupboard (only
allowed for kitchen installed in non-enclosed location) and
install the kitchen as island configuration with decorative
rear panels that block the back ventilation, or if the back
ventilation is restricted by pushing the kitchen against a
back wall, then a vented door kit (Part No. A18938401)
available from BeefEater Spare parts must be used to
ensure sufficient gas cylinder ventilation.
WARNING
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open hood and Outdoor Kitchen doors
4. If odour continues, immediately call your gas supplier
or your fire department.
For your safety
1. Do not store or use gasoline or other flammable
vapours or liquids in the vicinity of this or any other
appliance.
2. An LPG cylinder not connected for use, shall not be
stored in the vicinity of, or in any cupboard in this
kitchen.
TIPS & INFORMATION
IMPORTANT
Cleaning instructions:
Use warm soapy water with a soft cloth to clean the
kitchen. DO NOT use bleach based cleaners, abrasive
cleaners or objects with sharp edge (e.g. scraper) to clean
the kitchen surfaces as this may cause damage.
IMPORTANT SAFETY INSTRUCTIONS
44 DESCRIPTION
PRODUCT DESCRIPTION
TIPS & INFORMATION
IMPORTANT
Please note: Stone dimensions may vary ±2mm
700
900900
1900
700
55DESCRIPTION
WARNING
CAUTION
ASSEMBLY OF THIS UNIT SHOULD BE CARRIED OUT BY A QUALIFIED TRADESMAN
NO. PART NAME QTY.
11 Adjustable feet
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x10
12 Kick board clips
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x4
13 Regular hinges
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x4
14 Screws (M4 x 16mm)
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x80
Counter top
Heat-resistant bracket
Carcass top
Carcass back
(1819x537x15mm)
Shelf
Divider panels
Carcass base
(1819x651x25mm)
Side panel
Waterfall
Kicker plate
10
11
12
13
14
1
2
3
4
5
6
7
8
9
NO. PART NAME QTY.
1Heat-resistant bracket
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x1
2Back panel grills
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x1
3Screws (M4 x 30mm)
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x13
4Cam screws
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x47
5Hinge mounts
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x8
NO. PART NAME QTY.
6Shelf pins and sockets
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x8
7Bottom panel grill
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x1
8Bolt and Nylock nut
(M4 x 25mm)
x4
9Eccentric hinges
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x4
10 Dowels
No. Part Name Qty
M4X30mm
4
23
10
80
Heat-resistant bracket
Screws
Shelf pins and sockets
Dowels
Adjustable feet
Screws
Eccentric hinges
36
8
Hinge mounts
Cam screws
M4X16mm
1
13
8
4
Regular hinges
3
kick board clips
2
1
Bottom panel grill
Back panel grills
8
Screws
M4X8mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
x23
6CARCASS ASSEMBLY
CARCASS ASSEMBLY
Assembly Instruction – Proline Kitchen
1. Carcass assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
Turn unit right side up
Attach heat-resistant shields to carcass top
Level the cabinet by adjusting the feet
Attach base to carcass Attach carcass top
Attach side panels to back panel
Ensure the height from the ground to the top of the
carcass is minimum 735mm high in order to ensure
at least 5mm gap from the bottom of the waterfall
to the ground
①
A
④ ⑤
BC
D E
F
②
③
Feet assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
7CARCASS ASSEMBLY
1 Attach side panels to back panel
Assembly Instruction – Proline Kitchen
1. Carcass assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
Turn unit right side up
Attach heat-resistant shields to carcass top
Level the cabinet by adjusting the feet
Attach base to carcass Attach carcass top
Attach side panels to back panel
Ensure the height from the ground to the top of the
carcass is minimum 735mm high in order to ensure
at least 5mm gap from the bottom of the waterfall
to the ground
①
A
④ ⑤
BC
D E
F
②
③
Feet assembly
2 Attach base to carcass
Assembly Instruction – Proline Kitchen
1. Carcass assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
Turn unit right side up
Attach heat-resistant shields to carcass top
Level the cabinet by adjusting the feet
Attach base to carcass Attach carcass top
Attach side panels to back panel
Ensure the height from the ground to the top of the
carcass is minimum 735mm high in order to ensure
at least 5mm gap from the bottom of the waterfall
to the ground
①
A
④ ⑤
BC
D E
F
②
③
Feet assembly
3 Attach heat-resistant shields to carcass top
Assembly Instruction – Proline Kitchen
1. Carcass assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
Turn unit right side up
Attach heat-resistant shields to carcass top
Level the cabinet by adjusting the feet
Attach base to carcass Attach carcass top
Attach side panels to back panel
Ensure the height from the ground to the top of the
carcass is minimum 735mm high in order to ensure
at least 5mm gap from the bottom of the waterfall
to the ground
①
A
④ ⑤
BC
D E
F
②
③
Feet assembly
Use M4 x 30mm screws to fix the heat-resistant shield
4 Attach carcass top
Assembly Instruction – Proline Kitchen
1. Carcass assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
Turn unit right side up
Attach heat-resistant shields to carcass top
Level the cabinet by adjusting the feet
Attach base to carcass Attach carcass top
Attach side panels to back panel
Ensure the height from the ground to the top of the
carcass is minimum 735mm high in order to ensure
at least 5mm gap from the bottom of the waterfall
to the ground
①
A
④ ⑤
BC
D E
F
②
③
Feet assembly
5 Level the cabinet by adjusting the feet
Assembly Instruction – Proline Kitchen
1. Carcass assembly
Cam lock and dowel assembly method
Side panel
Heat-resistant bracket
Divider panels
Kicker plate
Top panels
Carcass back
Turn unit right side up
Attach heat-resistant shields to carcass top
Level the cabinet by adjusting the feet
Attach base to carcass Attach carcass top
Attach side panels to back panel
Ensure the height from the ground to the top of the
carcass is minimum 735mm high in order to ensure
at least 5mm gap from the bottom of the waterfall
to the ground
①
A
④ ⑤
BC
D E
F
②
③
Feet assembly
Ensure the height from the ground to the top of the carcass
is minimum 735mm high in order to ensure at least 5mm
gap from the bottom of the waterfall to the ground
8HINGE AND DOOR ASSEMBLY
HINGE AND DOOR ASSEMBLY
Use eccentric hinges (item #9) and M4 x 12mm screws for the centre doors
and use regular hinge (item #13) and M4 x 16mm screws for outer doors
Regular hinge
Hinge mounts
Door
Use M4 x 16mm screws
Eccentric hinges
Use M4 x
25mm bolts
and Nylock
nuts
Use M4 x
16mm screws
to attach
hinges to
the doors
9HINGE AND DOOR ASSEMBLY
Completed wooden carcass
Completed wooden carcass
AB
CD
Completed wooden carcass
AB
CD
10
STONE ASSEMBLY
STONE ASSEMBLY
3. Stone assembly
Waterfall
①②
Use M4 x 30mm screw to fix the waterfall
Shelf pin
Shelf
Locate disc into hole
Assemble shelves
Completed unit
Optional LPG cylinder storage location if kitchen
located in outdoor non-enclosed area - use LPG
vented door kit Part No. A18938401 available
from BeefEater spare parts if the kitchen is
installed in island configuration with decorative
back panels blocking the vents, or if the kitchen
is pushed up against a back wall restricting the
ventilation. The vented door is required in these
situations to ensure adequate cylinder ventilation
for safe operation.
3. Stone assembly
Waterfall
①②
Use M4 x 30mm screw to fix the waterfall
Shelf pin
Shelf
Locate disc into hole
Assemble shelves
Completed unit
Optional LPG cylinder storage location if kitchen
located in outdoor non-enclosed area - use LPG
vented door kit Part No. A18938401 available
from BeefEater spare parts if the kitchen is
installed in island configuration with decorative
back panels blocking the vents, or if the kitchen
is pushed up against a back wall restricting the
ventilation. The vented door is required in these
situations to ensure adequate cylinder ventilation
for safe operation.
3. Stone assembly
Waterfall
①②
Use M4 x 30mm screw to fix the waterfall
Shelf pin
Shelf
Locate disc into hole
Assemble shelves
Completed unit
Optional LPG cylinder storage location if kitchen
located in outdoor non-enclosed area - use LPG
vented door kit Part No. A18938401 available
from BeefEater spare parts if the kitchen is
installed in island configuration with decorative
back panels blocking the vents, or if the kitchen
is pushed up against a back wall restricting the
ventilation. The vented door is required in these
situations to ensure adequate cylinder ventilation
for safe operation.
Assemble shelves
When assembling
the waterfalls to the
cabinet, the top of
the waterfall must be
level with the top of
the cabinet, and there
must be clearance
between the bottom
of the waterfall and
the ground, adjust
the leveling legs as
required.
This document sets out the terms and conditions of the product
warranties for BeefEater Appliances. It is an important document.
Please keep it with your proof of purchase documents in a safe place
for future reference should there be a manufacturing defect in your
Appliance. This warranty is in addition to other rights you may have
under the Australian Consumer Law.
1. In this warranty:
(a) ‘ACL’ or ‘Australian Consumer Law’ means Schedule 2 to the
Competition and Consumer Act 2010;
(b) ‘Appliance’ means any Electrolux product purchased by you and
accompanied by this document;
(c) ‘ASC’ means Electrolux’s authorised serviced centres;
(d) ‘BeefEater’ is the brand controlled by Electrolux Home Products Pty Ltd
of 163 O’Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in
respect of Appliances purchased in Australia and Electrolux (NZ) Limited
(collectively “Electrolux”) of 3-5 Niall Burgess Road, Mount Wellington, in
respect of Appliances purchased in New Zealand;
(e) ‘WarrantyPeriod’meanstheperiodspeciedinclause3ofthis
warranty;
(f) ‘you’ means the purchaser of the Appliance not having purchased the
Appliance for re-sale, and ‘your’ has a corresponding meaning.
2. Application: This warranty only applies to new Appliances, purchased
and used in Australia or New Zealand and is in addition to (and does not
exclude, restrict, or modify in any way) other rights and remedies under
a law to which the Appliances or services relate, including any non-
excludable statutory guarantees in Australia and New Zealand.
3. Warranty Period: Subject to these terms and conditions, this warranty
continues for in Australia for a period of 24 months and in New Zealand
for a period of 24 months, following the date of original purchase of the
Appliance.Speciccomponentsarewarrantedagainstmanufacturing
defects in Australia and New Zealand for the periods listed below;
• Stainless Steel Box – Further 23 years parts only
• Enamel burner box – Further 8 years parts only
• Stainless steel plates, grills and burners – Further 3 years parts only
• Cast iron plates, grills and burners – Further 1 year parts only
4. Repair or replace warranty: During the Warranty Period, Electrolux
or its ASC will, at no extra charge if your Appliance is readily accessible
for service, without special equipment and subject to these terms and
conditions, repair or replace any parts which it considers to be defective.
Electrolux may, in its absolute discretion, choose whether the remedy
oeredforavalidwarrantyclaimisrepairorreplacement.Electroluxorits
ASC may use refurbished parts to repair your Appliance. You agree that
any replaced Appliances or parts become the property of Electrolux.
5. Travel and transportation costs: Subject to clause 7, Electrolux will
bear the reasonable cost of transportation, travel and delivery of the
Appliance to and from Electrolux or its ASC. Travel and transportation will
be arranged by Electrolux as part of any valid warranty claim.
6. Proof of purchase is required before you can make a claim under this
warranty.
7. Exclusions: You may not make a claim under this warranty unless the
defect claimed is due to faulty or defective parts or workmanship. This
warranty does not cover:
(a) lightglobes,batteries,ltersorsimilarperishableparts;
(b) parts and Appliances not supplied by Electrolux;
(c) cosmeticdamagewhichdoesnotaecttheoperationofthe
Appliance;
(d) damage to the Appliance caused by:
(i) negligence or accident;
(ii) misuse or abuse, including failure to properly maintain or service;
(iii) improper, negligent or faulty servicing or repair works done by
anyone other than an Electrolux authorised repairer or ASC;
(iv) normal wear and tear;
(v) power surges, electrical storm damage or incorrect power supply;
(vi) incomplete or improper installation;
(vii) incorrect, improper or inappropriate operation;
(viii) insect or vermin infestation;
(ix) failure to comply with any additional instructions supplied with
the Appliance;
In addition, Electrolux is not liable under this warranty if:
(a) the Appliance has been, or Electrolux reasonably believes that the
Appliance has been, used for purposes other than those for which
the Appliance was intended, including where the Appliance has
been used for any non-domestic purpose;
(b) theApplianceismodiedwithoutauthorityfromElectroluxinwriting;
(c) the Appliance’s serial number or warranty seal has been removed
or defaced.
8. How to claim under this warranty: To enquire about claiming under this
warranty, please follow these steps:
(a) carefully check the operating instructions, user manual and the
terms of this warranty;
(b) have the model and serial number of the Appliance available;
(c) have the proof of purchase (e.g. an invoice) available;
(d) telephone the numbers shown below.
9. Australia: For Appliances and services provided by Electrolux in
Australia: Electrolux goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to
have the Appliance repaired or replaced if the Appliance fails to be of
acceptable quality and the failure does not amount to a major failure.
‘Acceptable quality’ and ‘major failure’ have the same meaning as
referred to in the ACL.
10. New Zealand: For Appliances and services provided by Electrolux
in New Zealand, the Appliances come with a guarantee by Electrolux
pursuant to the provisions of the Consumer Guarantees Act, the Sale of
Goods Act and the Fair Trading Act. Where the Appliance was purchased
in New Zealand for commercial purposes the Consumer Guarantee Act
does not apply.
11.Condentiality: You accept that if you make a warranty claim, Electrolux
and its agents including ASC may exchange information in relation to you
to enable Electrolux to meet its obligations under this warranty.
Warranty
FOR SALES IN AUSTRALIA AND NEW ZEALAND
APPLIANCE: BEEFEATER SIGNATURE BBQ
BSig_BBQ_Warr_Jul19
Important Notice
Before calling for service, please ensure that the steps listed in clause 8 above have been followed.
AUSTRALIA
FOR SERVICE
ortondtheaddressofyournearest
authorised service centre in Australia
PLEASE CALL 1300 307 939
For the cost of a local call
FOR SPARE PARTS
ortondtheaddressofyournearest
spare parts centre in Australia
PLEASE CALL 13 13 50
For the cost of a local call
NEW ZEALAND
FOR SERVICE
ortondtheaddressofyournearest
authorised service centre in New Zealand
PLEASE CALL 0800 10 66 10
FOR SPARE PARTS
ortondtheaddressofyournearest
spare parts centre in New Zealand
PLEASE CALL 0800 10 66 20
AUSTRALIA
phone: 1300 307 939
email: customercare@electrolux.com.au
web: beefeaterbbq.com
NEW ZEALAND
phone: 0800 436 245
email: customercare@electrolux.co.nz
web: beefeaterbbq.com
For more information on all Beefeater products, or for
dimension and installation information, call into your
retailer, phone or email our customer care team or visit
our website:
Beefeater. We are part of the Electrolux Family.
To add a touch of professional inspiration to
your home, visit electrolux.com.au
© 2019 Electrolux Home Products Pty Ltd.
ABN 51 004 762 341
BINS_Proline_ODK_Sept19
This manual suits for next models
2
Table of contents
Other Beef Eater Kitchen Appliance manuals
