Beko DRVS 62 S User manual

Vented
Sensor Dryer
DRVS 62 W
DRVS 62 S

Please read this manual rst!
Dear Customer,
We hope that your product which has been manufactured in modern facilities and
passed through a strict quality control procedure will give you the best results.
Therefore, we advise you to read through this manual carefully before using your
product and keep it for future reference.
This operation manual will...
…help you use your machine in a fast and safe way.
• Please read the Operation Manual before installing and starting your machine.
• Particularly follow the instructions related to safety.
• Keep this Operating Manual within easy reach. You may need it in the future.
• Please read all additional documents supplied with this machine.
Please note that this Operating Manual may be applicable for several other models.
Differences between models will be identified in the manual.
Explanation of symbols
Throughout this Operation Manual the following symbols are used:
A Important safety information
This is the general warning sign. It is used to alert the user to potential hazards. All
safety messages that follow this sign shall be obeyed to avoid possible harm.
B Caution, risk of electric shock
Caution, risk of re
Caution, hot surface
Read the instructions
C Useful information.
Important information or useful hints about usage.

3 - EN
1 Your Dryer 4
Overview .............................................4
2 Important Safety
Instructions 5
3 Installation 7
Appropriate installation location ..........7
Adjusting the feet .................................7
Ventilation hose and connection (for
products equipped with an outlet vent) 7
Connection to a water drain (for products
equipped with a condenser ) ...............8
Destroying the packaging material .......9
Disposing of the old machine ...............9
4 Electrical Connection 10
Electrical requirements .......................10
Fitting a different plug .......................10
Washer/dryer combination .................10
5 Initial preparations for
drying 11
Garments suitable for drying in
the machine .......................................11
Garments unsuitable for drying in
the machine .......................................11
Preparing clothes to be dried .............11
Correct load capacity ........................11
Loading door .....................................12
6 Selecting a Programme
and Operating Your Machine 13
Control panel .....................................13
Turning the machine on .....................14
Programme selection .........................14
Programme selection and
consumption table .............................15
Auxiliary function ................................16
Warning indicators .............................16
Starting the Programme ....................16
Progress of programme .....................16
Changing the programme after
the programme has started ...............16
Child-proof lock .................................17
Ending the programe through
canceling ...........................................17
Technical Specifications .....................18
End of programme ............................18
7 Quick instructions for
daily use 19
8 Maintenance and
cleaning 20
Cover filter ........................................20
Sensor (models equipped with
a sensor) ...........................................20
Water tank (Products equipped
with a condenser); .............................20
For the condenser (products
equipped with a condenser); .............21
9 Solution suggestions for
problems 22
10 Door Reversal 23
11 Guarantee 24
12 Service 25
TABLE OF CONTENTS

4 - EN
1- Type label
2- Control Panel
3- Lint filter
4- Power Cord
5- Adjustable Feet
Overview
1 Your Dryer
Specifications of this appliance may change without notice to improve the quality of the
product. Figures in this manual are schematic and may not match your product exactly.
Values stated on the machine labels or in the documentation accompanying it are
obtained in laboratory in accordance with the relevant standards. Depending on
operational and environmental conditions of the appliance, values may vary.
2
3
5
1
4

5 - EN
2 Important Safety Instructions
A WARNING: To reduce the risk
of fire, electric shock, or injury to
persons when using your appliance,
follow basic precautions including
the following:
• Read all instructions before using the
appliance. Otherwise, there may be
the risk of personal injury or material
damage. Moreover, any warranty and
reliability commitment will become void.
A This product has been designed
for home use only.
• Your machine can be operated at
temperatures between +5°C and
+35°C.
• The appliance must not be installed
behind a lockable door, a sliding door
or a door with a hinge on the opposite
side to that of the tumble dryer.
• Do not install or store this appliance
where it will be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of
the appliance or attempt any servicing
unless specifically recommended in
the user-maintenance instructions or in
published user-repair instructions that
you understand and have the skills to
carry out.
• Unplug the machine when it is not in
use.
• Never wash down the appliance with
water! There is the risk of electric
shock!
• Never touch the plug with wet hands.
• Never pull from the cable to unplug the
machine.
• Do not operate the machine if the
power cord or plug is damaged.
• Never attempt to repair the machine
yourself.
• For malfunctions that cannot be solved
by information in the operating manual:
Turn off and unplug the appliance and
call an authorized service agent.
• This appliance must be grounded. In
the event of malfunction or breakdown,
grounding will reduce the risk of
electric shock by providing a path of
least resistance for electric current.
This appliance is equipped with a
cord having an equipment-grounding
conductor and a grounding plug.
The plug must be plugged into an
appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
B WARNING: Improper connection of
the equipment-grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician or
service represantative or personnel
if you are in doubt as to whether the
appliance is properly grounded.
• Power cord plug must be within easy
reach after installation.
• To reduce the risk of fire or electrical
shock, do not use extension cords,
multi-plugs or an adapter to connect
the dryer to electrical mains.
• Do not modify the plug provided with
the appliance: if it will not fit the outlet,
have a proper outlet installed by a
qualified electrician.
• If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
• The appliance must not be operated
unless it is repaired! There is the risk of
electric shock!
• Ventilation openings in the base must
not be obstructed by a carpet, etc.
• Exhaust air must not be discharged
into a flue, which is used for exhausting
fumes from appliances burning gas or
other fuels.
• Adequate ventilation has to be provided
to avoid the back flow of gases into the
room from appliances burning other
fuels, including open fires.

6 - EN
• Do not dry articles that have been
previously cleaned in, washed in,
soaked in or spotted with petrol/
gasoline, dry-cleaning solvents or other
flammable or explosive substances as
they give off vapors that could ignite or
explode.
• Do not use the tumble dryer if industrial
chemicals have been used for cleaning.
• Do not dry unwashed items in the
tumble dryer.
• Items that have been soiled with
substances such as cooking oil,
acetone, alcohol, petrol, kerosene,
spot removers, turpentine, waxes
and wax removers should be washed
in hot water with an extra amount of
detergent before being dried in the
tumble dryer.
• Items such as foam rubber (latex foam),
shower caps, waterproof textiles,
rubber backed articles and clothes or
pillows fitted with foam rubber pads
should not be dried in the tumble dryer.
• Do not use fabric softeners or products
to eliminate static unless recommended
by the manufacturer of the fabric
softener or product.
• The appliance may only be used for
drying of textiles that are marked
accordingly.
• Undergarments that contain metal
reinforcements should not be placed in
a tumble dryer. Damage to the tumble
dryer can result if metal reinforcements
come loose during drying.
• Check all garments for forgotten
lighters, coins, metal pieces, needles,
etc. before loading.
• Fabric softeners, or similar products,
should be used as specified by the
fabric softener instructions.
• The final part of a tumble dryer cycle
occurs without heat (cool-down cycle)
to ensure that the items are left at a
temperature that ensures that the items
will not be damaged.
A WARNING: Never stop the tumble
dryer before the end of the drying
cycle unless all items are quickly
removed and spread out so that the
heat is dissipated.
• Do not reach into the appliance if the
drum is moving.
• Do not allow children to play on or in
the appliance.
• Young children should be supervised
to ensure that they do not play with the
appliance.
• Before the appliance is removed from
service or discarded, remove the door
to the drying compartment.
• Close the loading door when you leave
the area where the machine is located.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
• Clean lint screen before or after each
load.
• Keep area around the exhaust opening
and adjacent surrounding areas free
from the accumulation of lint, dust, and
dirt.
• The interior of the appliance and
exhaust duct should be cleaned
periodically by qualified service
personnel.
• Never use the dryer without the lint filter.
SAVE THESE INSTRUCTIONS

7 - EN
Appropriate installation
location
• Install your machine in environments
which have no risk of freezing and in a
stable and level position.
• Do not place your machine on a long
pile rug or on similar surfaces.
• Operate your machine in a well
ventilated, dust-free environment.
• Do not block the air ducts in front of
and under the machine with materials
such as long pile rugs or kitchen unit
plinths.
B Make sure that your machine is not
placed on the power cable.
B Keep at least 3 cm from the edges of
other furniture.
Under Counter Installation
• Leave at least 3 cm of space between
the side and rear walls of the machine
and the walls of the counter/cupboard
when installing your machine under a
counter or in a cupboard. Never use
the tumble dryer without top plate.
Adjusting the feet
In order to ensure that your machine
operates more silently and vibration-free,
it must stand level and balanced on its
feet. Front feet of your machine can
be adjusted. Balance the machine by
adjusting the feet.
1. Loosen the feet by hand.
2. Adjust them until the machine stands
level and firmly.
C Do not use any tools to loosen the
adjustable feet. Otherwise, they can be
damaged.
C Never unscrew the adjustable feet
from their housings.
2 plastic pieces supplied together with
the Operating Instructions prevent
your machine from slipping on wet and
slippery surfaces. To install these plastic
parts:
1. Tilt your machine to backwards.
2. Fit the plastic parts to the front
adjustable feet. Press on the plastic
parts to fix them in their places.
3. Check the balance of your machine
again and readjust the adjustable feet if
necessary.
Ventilation hose and
connection (for products
equipped with an outlet vent)
Ventilation hose assures exhausting of the
air from inside the machine.
Vented dryer has 1 air outlet.
Stainless sheet metal or aluminum pipes
can be used instead of the hose. The
diameter of the pipe to be used should
be minimum 10 cm.
Maximum hose and pipe lengths are
given in the table below.
Hose Pipe
Maximum length 4 m 5 m
1 elbow 45° -1.0 m -0.3 m
1 elbow 90° -1.8 m -0.6 m
1 elbow 90° short -2.7 m
1 wall passage -2.0 m -2.0 m
C Each elbow and other passages
should be subtracted from the above
maximum length.
To connect a ventilation hose;
1. Connect the air outlet hose to the
hose spacer piece by turning it anti-
clockwise.
2. Make the hose passages as shown
below.
3 Installation

8 - EN
C Exhaust of humid air from the dryer
into the room is inconvenient. It may
damage the walls and furniture in the
room.
C The ventilation hose can be routed
outdoors via a window or it can be
connected to an air outlet in the wall
(see diagram below).
C Air outlet hose must be extended
directly to the outdoors. There must
be a small number of elbows as not to
hinder air ventilation.
C To prevent water accumulation in the
hose, make sure that it is not folded on
the floor.
B The air ventilation hose should not be
connected to the chimney of a stove or
a fireplace.
B Do not operate your machine at the
same time with heaters such as a coal
or gas stove. Airflow may cause the
chimney to flare up. Airflow may cause
the chimney to flame up.
Connection to a water drain
(for products equipped with a
condenser )
In products equipped with a condenser
unit the water accumulated during the
drying cycle is collected in the water tank.
You should drain the accumulated water
after each washing cycle.
You can directly send the accumulated
water out through the water drain hose
supplied with the machine instead of
periodically draining the water collected in
the water tank.
Connecting the water drain hose;
1. Remove the hose on the machine by
pulling it out from its end. Do not use
any tools to take out the hose. Attach
the drain hose adaptor to the end of
this hose.
2. Connect the special drain hose
supplied with the machine to the hose
adaptor fitting.
3. The other end of the drain hose
can be directly connected to the
wastewater drain or to the washbasin.
The fitting must always be secured in
all types of connections. Your house
may be flooded if the hose gets out of
its housing during water discharge.
C When you direct the water drain out,
“Water Tank” warning LED will light up
at the end of each programme.
Important:
• The hose should be attached to a
height of maximum 80 cm.
• You must be careful not the pinch or
bend the hose.
• The end of the hose should not be
bent, it should not be stepped on and
it must not be folded between the
drain and the machine.

9 - EN
Destroying the packaging
material
Packaging material can be dangerous to
children. Keep the packaging materials
out of the reach of children or dispose of
them accordingly. Do not dispose them
together with normal domestic wastes.
Packaging materials of your machine are
manufactured from recyclable materials.
Disposing of the old machine
Dispose of your old appliance in an
environmental friendly manner.
• You may refer to your local agent or
solid waste collection center in your
municipality to learn how to dispose of
your machine.
Before disposing of your old washing
machine, cut off the mains plug and
make the door lock unusable.

10 - EN
Make sure that you have an earthed
power outlet socket rated at 13 amps
(minimum).
Attention!
If you use your dryer as built-in,
the socket must be reachable after
installation, or a separate switch (which
can disconnect the two poles) must
be used in the installation. Check for
suitability.
For a permanent connection, a master
switch with at least 3mm contact
clearance and minumum 13 A rating
must be used.
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown in the rating label
corresponds to your electricity supply.
We recommend that this appliance be
connected to the mains supply via a
suitable switched and fused socket in a
readily accessible position.
Should the mains lead of the appliance
become damaged or need replacing at
any time, it must be replaced by a special
purpose made mains lead which can only
be obtained from a Authorised Service
Agent.
A Warning
This appliance must be earthed
If the fitted moulded plug is not suitable
for your socket, then the plug should be
cut off and an appropriate plug fitted.
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse
need to be replaced an ASTA approved
BS1362 fuse of the same rating must
be used. Do not forget to refit the fuse
cover. In the event of losing the fuse
cover, the plug must not be used until a
replacement fuse cover has been fitted.
Colour of the replacement fuse cover
must be the same colour as that visible
on the pin face of the plug. Fuse covers
are available from any good electrical
store.
In order to avoid hazards, damaged
supply cord should be replaced by the
manufacturer, its service agent or similarly
qualified people.
Built-under installation
This appliance can be installed under a
worktop.
A Only authorised specialists are
permitted to car ry out a built-under
installation. Risk of electric shock!
A Important
Fitting a different plug
As the colours of the wires in the
mains lead of this appliance may not
correspond with the coloured markings
identifying the terminals on your plug,
proceed as follows:
1 Connect the green - yellow or green
(earth) wire to the terminal in the plug
marked ‘E’ or with the symbol or
coloured green and yellow or green.
2 Connect the blue (neutral) wire to
the terminal in the plug marked ‘N’ or
coloured black.
3 Connect the brown (live) wire to
the terminal in the plug marked ‘L’ or
coloured red.
With the alternative plugs a 13A fuse
must be fitted either in the plug or
adaptor or in the main fuse box. If in
doubt contact a qualified electrician.
Washer/dryer combination
Do not stack washing machine on top
of the tumble dryer. This would damage
both appliances and guarantees would
become void. It is also unsafe to stack
an appliance on top of another without
using a suitable and approved stacking
kit obtained from the manufacturer of the
appliances.
• A special stacking kit is required as an
optional extra please contact customer
service.
4 Electrical Connection
Green and yellow
or green
N
Blue or black L
Brown or red

11 - EN
Garments suitable for drying in
the machine
Always follow the advice on the garment
labels. With this dryer, dry only the
laundry having a label stating that they
are suitable for drying in a dryer by
selecting the appropriate programme.
Garments unsuitable for drying
in the machine
• Laundry items and attachments made
of or contain metal, hard plastic and
similar materials, such as belt buckles,
jeans, bra wires, buttons and similar
accessories will damage your machine
and may cause breakdown. So do not
place such items in the tumble dryer. If
you are in doubt, please call Customer
Help Line.
• Do not dry items such as woolen, silk
garments and nylon stockings, delicate
embroidered fabrics, garments with
metal accessories and items such as
sleeping bags in the machine.
• Garments made of delicate and
valuable fabrics as well as lace curtains
can be creased. Do not dry these in
your machine!
• Do not dry items made of hermetic
fibers such as pillows and quilts in the
drying machine.
• Garments made of foam or rubber may
be deformed.
• Do not dry clothes containing rubber in
the machine.
• Do not dry clothes exposed to
petroleum, oil, combustible or explosive
agents in the machine even if they are
washed beforehand.
• Overly wet laundry or laundry with
dripping water must not be put into the
machine.
Preparing clothes to be dried
• All laundry must be spun at the highest
possible spin speed your washing
machine allows for the textile type.
• Laundry may be tangled after washing.
Separate your laundry before placing
them into your dryer.
• Sort your laundry according to their
types and thicknesses. Dry the same
type of laundry together. E.g..: fine
kitchen towels and table cloths dry
faster than the thick bath towels.
Correct load capacity
A Please consider the information in the
“Programme Selection Table”. Always
start the programme in accordance
with the maximum load capacity.
C Adding laundry to the machine
more than the level shown in the
figure is not recommended.. Drying
performance will degrade when the
machine is overloaded. Furthermore,
your machine and your clothes might
be damaged.
5 Initial preparations for drying
A B C
l mn
o p q
D

12 - EN
C Place your garments into the drum
loosely so that they will not get
tangled..
C Large pieces (E.g.: bed sheets, quilt
covers, large tablecloths) may bunch-
up. Stop the machine 1-2 times
during drying process to separate
bunched-up laundry.
Following weights are given as examples.
Home articles Approximate
weights (gr)
Cotton quit covers (double) 1500
Cotton quit covers (single) 1000
Bed sheets (double) 500
Bed sheets (single) 350
Large tablecloths 700
Small tablecloths 250
Tea napkins 100
Bath towels 700
Hand towels 350
Garments Approximate
weights (gr)
Blouses 150
Cotton shirts 300
Shirt 200
Cotton dresses 500
Dresses 350
Jeans 700
Handkerchiefs 100
T-Shirts 125
Loading door
• Open the loading door.
• Place laundry items loosely into the
machine.
• Push the loading door to close. Ensure
that no items are caught in the door.

13 - EN
6 Selecting a Programme and Operating Your Machine
Control panel
Figure 2
6. On/Off button
7. Programme selection knob
8. Start/Pause/Cancel button
9. Cancel Audio Warning
10. Programme follow-up indicator
11. Filter cleaning warning LED
12. Water tank full warning LED *
13. Time Delay Button *
* It may change according to the
specifications of your dryer
11 6
87
9
10
Ready to
Wear
Ready to
Iron
Ready to Iron
Ready to Wear
Extra dry
Cottons
Delicates
Freshen Up
Synthetics
Timed
Programmes
10 min
20 min
40 min
60 min
On / Off
Clean Filter
End / Anticrease
Drying
Ready to
Iron
Ready to
Wear
Start/
Pause/
Cancel
Buzzer
Cancel

14 - EN
Turning the machine on
Prepare machine for programme
selection by pressing the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme
has started. Press "Start/Pause/
Cancel" button of the machine to start
the programe.
Programme selection
Decide the appropriate programme from
the table below which includes drying
temperature in degrees. Select the
desired programme with the programme
selection button.
Extra dry Dry at high
temperature only for
cotton laundry. Thick
and multi layered
laundry (E.g.: towels,
linens, jeans) are dried
in a way that they do
not require ironing
before placing in the
wardrobe.
Ready to
Wear
Normal laundry (E.g.:
tablecloths, underwear)
are dried in a way that
they do not require
ironing before placing
in the drawers.
Ready to Iron Normal laundry (E.g.,
Shirts, dresses) are
dried ready to be
ironed.
C Always select the highest temperature
required for drying. High temperature
will ensure energy and time saving.
C For further programme details, see,
“Programme Selection Table”
Main programmes
Depending on the type of textile, the
following main programmes are available:
•Cottons
You can dry your durable clothes with
this programme. Dries at a higher
temperature. It is recommended to
use for your cotton items (such as bed
sheets, quilt cover, underclothing, etc.).
•Synthetics
You can dry your less durable clothes
with this programme. It dries at a lower
temperature compared to the cottons
programme. It is recommended for your
synthetic clothes (such as shirts, blouses,
synthetic/cotton blended garments, etc.).
C Do not dry curtains and lace in your
machine.
•Anti-creasing
A 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry
out after the programme has come to
an end. This programme rotates the
laundry in 60-second intervals to prevent
creasing.
Special programmes
For special cases, there are also extra
programmes available:
C Additional programmes may differ
according to the model of your
machine.
•Delicates
You can dry at a lower temperature your
very delicate laundry (silk blouses, fine
underwear, etc.) that are suitable for drying
or laundry which is advised to be hand-
washed.
C It is recommended to use a cloth
bag to avoid certain delicate garments
and laundry from getting creased
or damaged. Take your garments
immediately out of the dryer and hang
them after the programme ends in
order to prevent them being creased.
•Ventilation
Only ventilation is performed for 10
minutes without blowing hot air. You
can air your clothes that have been kept
at closed environments for a long time
thanks to this programe to deodorize
unpleasant odors.
•Timer programmes
You can select one of the 10 min.,
20 min., 40 min., 60 min...... timer
programmes to achieve the desired
final drying level at low temperatures.
Programme dries at the selected time
regardless of the drying level.

15 - EN
Programme selection and consumption table
* : Energy Label standard programme (EN 61121:2005)
All values given in the table have been fixed according to EN 61121:2005 Standard.
These values may deviate from the table according to the laundry type, laundry spin
speed, environmental conditions and voltage fluctuations.
EN 2
Program table
Programs Capacity (kg) Spin speed in washing
machine (rpm)
Approximate
amount of
remaining humidity
Drying time (minutes)
Cottons / Coloreds
A Ready to Wear
61200-1000 % 60 110
900-800 % 70 130
31200-1000 % 60 80-60
900-800 % 70 110-80
B Ready to Iron
61200-1000 % 60 110-80
900-800 % 70 110
31200-1000 % 60 60-40
900-800 % 70 80-60
Synthetics
B Ready to Wear
3800 % 40 60-40
600 % 50 80-60
1.5 800 % 40 40-20
600 % 50 60-40
Delicates
B Ready to Wear 1.5 600 % 50 30
Energy consumption values
Programs Capacity (kg) Spin speed in washing
machine (rpm)
Approximate
amount of
remaining humidity
Energy consumption
value kWh
Cottons linen Ready to wear* 6 1000 % 60 3.39
Cottons Ready to iron 6 1000 % 60 2.90
Synthetics&Mixed fabrics Ready
to wear 3 600 % 50 1.80

16 - EN
Auxiliary function
Cancel Audio Warning
Your machine will send out an audio
warning when the programme comes to
an end. If you do not want to hear this
buzzing, you need to press the “Cancel
Audio Warning” button. The relevant LED
will light up when this button is pressed
and an audio warning will not be given
when the programme comes to an end.
C You can select this function either
before or after the programme starts.
Warning indicators
C Warning indicators may differ
according to the model of your
machine.
Filter cleaning
A warning LED will light up to remind
filter cleaning after the programme
finishes.
C If the filter cleaning warning LED
lights up continuously, please refer to,
“Solution suggestions for problems”.
Water tank
A warning LED will light up at the end
of the programme or when the tank is full
with water. The machine stops operating
when this warning LED lights up during
a programme running. To restart the
machine, please drain the water in
the water tank. Press "Start/Pause/
Cancel" button to start the programme
after you have emptied the water tank.
The warning LED goes off and the
programme resumes operating.
Starting the Programme
1. Press “Start/Pause/Cancel” button to
start the programme.
2. “Start/Pause/Cancel” button will light
up to indicate that the programme has
started.
Progress of programme
Progress of a running programme is
shown through the programme follow-up
indicator.
At the beginning of every programme
step, the relevant indicator LED will light
up and light of the completed step will
turn off.
“Drying”:
- Drying level will be illuminated during
the whole drying process until the drying
degree reaches “ Ready to Iron “.
“ Ready to Iron “:
- Starts to illuminate when the drying
degree reaches “ Ready to Iron “ step and
remains illuminated until the next step.
“ Ready to Wear “:
- Starts to illuminate when the drying degree
reaches “ Ready to wear “ step and remains
illuminated until the next step.
“Final / Anti-creasing”:
- Illuminates when the programme comes
to an end and anti-creasing function is
activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Changing the programme after
the programme has started
You can use this feature after your machine
has started to dry your clothes under higher
or lower temperatures.
For example;
Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to “Cancel”
the programme in order to select “Extra
Dry” programme instead of “Iron Dry”
programme.
Select the “Extra Dry” programme by
rotating the programe knob.
Press “Start/Pause/Cancel” button to start
the programme.
C The programme which is selected first
will go on even if the programme selection
button is moved and another programme
mode is selected while the machine is
operating. You must cancel the ongoing
programe in order to change the drying
programme. (See, Ending the programme
through canceling)

17 - EN
Ending the programe through
canceling
The programme which is selected first will
keep on going even if the position of the
programme selection button is changed.
A new programme can be selected and
started after “Programme cancel” is
activated in order to change the drying
programme.
To cancel any selected programme;
• Press “Start/Pause/Cancel” button for
about a duration of 3 seconds. The “Filter
cleaning”, “Water tank” and “End/ Anti-
creasing” warning LEDs will light up at the
end of this period for reminding purposes.
A As the inside of the machine will be
excessively hot when you cancel the
programme while the machine is running,
activate the ventilation programme to cool
it down.
A If the machine is stopped during any
drying programme, and if the position
of the programme selection knob is
changed, an audio signal will be heard
(if the “Cancel audio warning” function
is not selected).
The machine will not start even if the
“Start/Pause/Cancel” button is
pressed, unless the programme
selection knob is returned to the initial
programme. The paused programme
must be cancelled in order to change
the drying programme.
Adding/removing laundry in standby
mode
In order to add or take out laundry after the
start-up of the programme;
1. Press the “Start/Pause/Cancel” button
to switch the machine to “Pause” mode.
Drying process will stop.
2. Open the door at Pause position and
close it again after adding or taking out
laundry.
3. Press “Start/Pause/Cancel” button to start
the programme.
C Any laundry added after the drying
process was started may cause the
already dried clothes in the machine
intermingle with wet clothes and the
result will be wet laundry after the drying
process is over.
C Laundry may be added or taken out
as much as desired during a drying
process, but as this process will interrupt
drying continuously, it will extend the
programme duration and increase
energy consumption. Therefore, it is
recommended to add laundry before the
drying programme is started.
Child-proof lock
There is a childproof lock to prevent any
programme interruption due to the
pressing of keys while the programme
is on. The loading door and all keys
except the “On/Off” key on the panel are
deactivated when the child-proof lock is
active.
In order to activate the childproof lock,
press on the “Start/Pause/Cancel” and
“Cancel audio
warning” buttons
simultaneously for 3
seconds.
To start a new
programme after
the programme is
over or to interrupt
the programme, the childproof lock should
be deactivated. To deactivate the childproof
lock, press the same buttons for 3 sec.
C 2 beeps when activating and 1 beep
when deactivating the child-proof lock is
heard.

18 - EN
End of programme
The “End/Anti-creasing”, “Filter cleaning”
and “Water tank” warning LEDs on the
programme follow up indicator will light up
when the programme comes to an end.
The door can be opened and the machine
becomes ready for a second cycle.
Press the “On/Off” button to shut down the
machine.
C A 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry
out after the programme has come to an
end.
C Clean the filter after each drying (please
see, Filter cleaning).
C Drain the water tank after each drying
(please see, Water tank)
Technical Specifications
EN
Height (adjustable) 85.0 cm
Width 59.5 cm
Depth 54 cm
Capacity (max.) 6 kg
Weight (net) 31 kg
Voltage
See type labelRated power input
Model code
Type label is located behind the loading door.
This appliance’s packaging material is recyclable. Help recycle it and protect the
environment by dropping it off in the municipal receptacles provided for this purpose.
Your appliance also contains a great amount of recyclable material. It is marked with
this label to indicate the used appliances that should not be mixed with other waste.
This way, the appliance recycling organised by your manufacturer will be done under
the best possible conditions, in compliance with European Directive 2002/96/EC on
Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used
appliance collection points closest to your home. We thank you doing your part to protect the
environment.

19 - EN
7 Quick instructions for daily use
Preparation and starting
1. Press the “On/Off” button.
2. Place the laundry in the machine.
3. Select the programme.
4. Close the loading door.
5. Press “Start/Pause/Cancel” button.
Cancelling a programme
A new programme can be selected and
started after “Programme cancel” is
activated in order to change the drying
programme.
In order to cancel the selected
programme, press “Start/Pause/Cancel”
button for about 3 seconds. The “Filter
cleaning”, “Water tank” and “End/ Anti-
creasing” warning LEDs will light up at the
end of this period for reminding purposes.
Adding laundry
In order to add laundry after the start-up
of the programme:
1. Press “Start/Pause/Cancel” button.
2. Open the loading door and put the
laundry in.
3. Close the loading door.
4. Press “Start/Pause/Cancel” button to
start the programme.
Changing the programme after the
programme has started
You can use this feature after your
machine has started to dry your clothes
under higher or lower temperatures.
Press and hold the “Start/Pause/Cancel”
button for about 3 seconds to switch
the machine into the “Cancel” status in
order to change the programme. Change
the programme and press “Start/Pause/
Cancel” button to start it.
After the programme is finished
The “End/Anti-creasing” and “Filter
cleaning” warning LEDs as well as “Water
tank” warning LED in some models on
the programme follow up indicator will
light up when the programme comes to
an end. The door can be opened and the
machine becomes ready for a second
cycle.
1. Press the “On/Off” button to shut
down the machine.
2. Take out the laundry from the machine.
3. Check if there are any foreign
substances in the machine.
4. Clean the filter after drying. Also drain
the water tank in models equipped
with a condenser.

20 - EN
A Never use solvents, cleaning
agents or substances alike when
cleaning as these might cause fire and
explosion!
Water tank (Products equipped
with a condenser);
The moisture in the damp laundry is taken
from the laundry and condensed. Drain
the water tank after each drying cycle or
during drying when “Water tank” warning
LED comes on.
A Condensed water is not
drinkable!
C You can use the water in the water
tank in your steam irons or air
humidifiers.
A Never take out the water tank
when the programme is running!
Water tank may be located in two
different places as indicated below,
depending on the model of your machine.
Inside the drawer on the panel-
Inside the kick plate cover-
If you forget to drain the water tank, your
machine will stop during the following
drying cycles when the water tank is
full and the “Water tank” warning LED
will light on. If this is the case, press the
“Start/Pause/Cancel” button to resume
the drying cycle after draining the water
tank.
In order to drain the water tank;
1 Carefully remove the water tank by
opening the kick plate cover/pulling the
drawer.
2 Drain the water by opening the water
tank cover.
3 If there is lint accumulation in the water
tank cover, clean it and press to close.
4 Place the water tank into its seat.
Cover filter
Lint and fibres released from the laundry
to the air during the drying cycle are
collected in the “Cover Filter”.
C Such fibre and lint are generally
formed during wearing and washing.
C Always clean the filter after each
Drying process.
C You can clean the filter and filter
area by vacuum cleaner.
For Filter cleaning;
1 Take out the cover
2 Remove the cover filter by pulling it up
and open the filter.
3 Clean lint, fibre, and cotton raveling by
hand or with a soft piece of cloth.
4 Close the filter and place it back into its
seat.
Sensor (models equipped with
a sensor)
There are humidity sensors in your
machine that detect whether the laundry
is dry or not.
For sensor cleaning;
1 Open the cover of your machine.
2 Allow the machine to cool off if drying
has been carried out.
3 Wipe the metal sensors with a soft
cloth, dampened with vinegar and dry
them.
C Clean metal sensors 4 times a year.
8 Maintenance and cleaning