Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series User manual

Installation MTS8003/8006/8010
Release 01 12/2021
User Manual
Installation
MAMMUTHUS CORE LAYER SWITCH – MTS8003-Chassis
MAMMUTHUS CORE LAYER SWITCH – MTS8006-Chassis
MAMMUTHUS CORE LAYER SWITCH – MTS8010-Chassis
MAMMUTHUS POWER MODULE – MTM8000-PSU800
MAMMUTHUS ENGINE MODULE – MTM8000-Engine
MAMMUTHUS FAN MODULE – MTM8003-FAN
MAMMUTHUS FAN MODULE – MTM8006-FAN
MAMMUTHUS FAN MODULE – MTM8010-FAN
MAMMUTHUS MEDIUM MODULE – MTM8000 Series
MAMMUTHUS BLANK COVER – MTM8000 Series

2
Installation MTS8003/8006/8010
Release 01 12/2021
Even if not specifically stated, the copyrighted trademark names in this manual shall not be deemed
free of charge in the sense of the trademark and trade name protection act and thus freely available
to anyone.
© 2021 Belden Singapore Pte Ltd
Both the manual and software are protected by copyright. All rights reserved. All or any part of this
manual shall be prohibited from being reproduced, copied, translated or converted into any
electronic media or machine-scannable form, except in the case that you make a copy of the
software for your own use.
The performance characteristics described herein shall be binding only upon the express consent
of the parties at the time of signing the contract. This paper is produced by Belden within its
capacity. Belden reserves the right to change the contents of this manual without prior notice.
Belden does not guarantee the correctness or accuracy of the information in this manual.
Belden shall not be liable for damages caused by the use of network components or related
operating software. And the conditions of use specified in the license contract are referred to in this
manual.
You may access the latest version of this manual at the product website of Hirschmann IT:
https://catalog.belden.com

3
Installation MTS8003/8006/8010
Release 01 12/2021
Contents
Safety instructions8
About this manual 15
Key 16
1. Description 17
1.1 General device description 17
1.2 Device name and product code 26
1.2.1 Basic device 26
1.2.2 Power module 26
1.2.3 Engine module 27
1.2.4 Fan module 27
1.2.5 Medium module 28
1.2.6 Blank cover 29
1.3 Device view 30
1.3.1 MTS8000 series chassis 30
1.3.2 Power module 37
1.3.3 Engine module 38
1.3.4 Fan module 39
1.3.5 Medium module 41
1.3.6 Blank cover 42
1.4 Power supply 43
1.5 Device port attribute 43
1.5.1 Console port attribute 43
1.5.2 USB Console port attribute 43
1.5.3 10BASE-T/100BASE-TX/1000BASE-T RJ45 electric interface attribute 43
1.5.4 10GBASE-T RJ45 electric interface attribute 44
1.5.5 1000BASE-X SFP optical interface attribute 44
1.5.6 10GBASE-SR/LR/ER SFP+ optical interface attribute 44
1.5.7 40GBASE-SR4/LR4 QSFP+ optical interface attribute 45
1.5.8 100GBASE-SR4/LR4 QSFP+ 45

4
Installation MTS8003/8006/8010
Release 01 12/2021
1.5.9 USB interface attribute 45
1.5.10 SD interface attribute 46
1.5.11 PoE interface attribute 46
1.6 Display elements 46
1.6.1 Device state 47
1.6.2 Port status 47
1.7 Management interface 50
1.7.1 DC0 interface (external management) 50
1.7.2 USB interface 50
2Installation 51
2.1 Checking the package contents 51
2.2 Installing the power module (optional) 51
2.3 Installing and grounding the device 52
2.3.1 Installing the device in the switch cabinet 52
2.3.2 Installing the cable tray 55
2.3.3 Grounding the device 56
2.4 Installing the SFP transceiver (optional) 57
2.5 Operating the device 58
2.6 Connecting the data cables 58
2.7 Filling out the inscription label 58
3Making basic settings 59
4Monitoring the ambient air temperature 60
5Maintenance and service 61
6Disassembly 62
6.1 Removing the power module 62
6.2 Removing the engine or medium module 62
6.3 Removing the SFP transceiver 63
6.4 Removing the FAN module 64
6.5 Removing the device 64
7Technical data 65
7.1 General technical data 65

5
Installation MTS8003/8006/8010
Release 01 12/2021
7.2 Dimension Drawings 67
7.3 EMC and immunity 75
7.4 Network range 77
7.5 Power consumption/power output 79
8Scope of delivery, order number, and accessories 80
9Underlying technical standards 82
AFurther support 83

6
Installation MTS8003/8006/8010
Release 01 12/2021
Important information
Note: Read these instructions carefully, and familiarize yourself with the
device before trying to install, operate, or maintain it. The following notes
may appear throughout this documentation or on the device. These
notes warn of potential hazards or call attention to information that
clarifies or simplifies a procedure.
 Symbol explanation
This is a general warning symbol. This symbol alerts you to
potential personal injury hazards. Observe all safety notes
that follow this symbol to avoid possible injury or death.
If this symbol is displayed in addition to a safety instruction
of the type “Danger” or “Warning”, it means that there is a
danger of electric shock and failure to observe the
instructions will inevitably result in injury.
This symbol indicates the danger of hot surfaces on the
device. In connection with safety instructions, non-
observance of the instructions will inevitably result in
injuries.
DANGER draws attention to an immediately dangerous situation, which
will inevitably result in a serious or fatal accident if not observed.
DANGER
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
WARNING

7
Installation MTS8003/8006/8010
Release 01 12/2021
CAUTION indicates a possible danger which, if not avoided, may result in
minor injuries.
NOTICE provides information about procedures that do not involve the risk
of injury.
NOTICE
CAUTION

8
Installation MTS8003/8006/8010
Release 01 12/2021
Safety instructions
 General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
 Before connecting any cable, read this document, and the safety
instructions and warnings.
 Operate the device with undamaged components exclusively.
 The device is free of any service components. In case of a
damaged or malfunctioning device, turn off the supply voltage and
return the device to Hirschmann IT for inspection.
 Qualification requirements for personnel
 Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
 Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
prerequisite for grounding and labeling circuits, devices, and
systems in accordance with current standards in safety technology.
 Qualified personnel are aware of the dangers that exist in their work.
 Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow this instruction can result in death, serious injury, or
device damage.

9
Installation MTS8003/8006/8010
Release 01 12/2021
 Qualified personnel receive training on a regular basis.
 Correct usage
Only use the device for those purposes specified in the catalog and in
the technical description. Only operate the device with external devices
and components that are recommended and permitted by the
manufacturer. The proper and safe operation of this product depends
on proper handling during transport, proper storage, assembly and
installation, and conscientious operation and maintenance procedures.
 National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
 Ensure the integrity and consistency
Check the bond on the packaging to assure it is sealed and not
tampered by unauthorized party.
Verify serial number of delivered products to make sure it is unified
with a hardcopy serial number list provided by manufacturer. If it is
necessary, please contact Belden representative to obtain a
softcopy serial number list from manufacturer for double check.
 Requirements for the connecting the electrical wires
Before connecting the electric wire, make sure to always confirm
compliance with all listed requirements.
 The electrical wires are voltage-free.
 The cables used are permitted for the temperature range of the application case.
 Connect the ground screw on the back of the device to the protective conductor before
setting up other connections. When to remove connections, the protective conductor is
the last to be removed.
 Exclusively switch on the device when it is installed.
 Relevant for North America:
Use 60 °C / 75 °C (140 °F / 167 °F) or 75 °C (167 °F) copper (Cu) wires only.
Table 1: Requirements for connecting electrical wires
The following requirements apply without restrictions:

10
Installation MTS8003/8006/8010
Release 01 12/2021
 Requirements for connecting the supply voltage
Prerequisite:
All Variants
All of the following requirements are complied with:
 The supply voltage corresponds to the voltage specified on the type plate of the
device.
 The power supply conforms to overvoltage category I or II.
 The power supply has an easily accessible disconnecting device (for example a
switch or a plug). This disconnecting device is clearly identified. So in the case
of an emergency, it is clear which disconnecting device belongs to which power
supply cable.
 When to connect a power supply voltage with a protective conductor: first
connect the protective conductor, and then the power supply voltage. If the
device contains such a second power supply voltage connection module: first
connect the protective conductor, and then the power supply voltage.
 Supply with DC voltage: The wire diameter of the power supply cable is at least
1 mm² (North America: AWG16) on the supply voltage input.
 Supply with AC voltage: The wire diameter of the power supply cable is at least
0.75 mm² (North America: AWG18) on the supply voltage input.
 The cross-section of the ground conductor is the same size as or bigger than
the cross-section of the power supply cables.
 The power supply cable is suitable for the voltage, the current and the physical
load.
Table 2: Requirements for connection of supply voltage
 Shield grounding
The shielded earthing module of the twisted-pair cables is used as the
conductor for connection to the front panel.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
 ESD guide
The modules are equipped with electrostatic sensitive components.
If the connection is touched, these sensitive components can be
damaged or their service life shortened due to electric field or charge
balance effects.
You may find information about electrostatic hazard components in DIN
EN 61340-5-1 (2007-08) and DIN EN 61340-5-2 (2007-08).

11
Installation MTS8003/8006/8010
Release 01 12/2021
 Device casing
Only technicians authorized by the manufacturer are permitted to open
the casing.
Keep the cooling fins free to ensure good air circulation.
Verify that there is at least 10 cm (3.94 in) of space around the
cooling fins of the casing.
Install the device horizontally in the cabinet or vertically on a flat
surface. Operating the device as a table unit is inadmissible.
See “Installing and grounding the device” on page 52.
Operate the device at the maximum ambient air temperature and in
stacking: when to install the device, confirm that there is at least one
available rack space (approximately 5 cm) above the device to allow
heat to escape through the enclosure of the device.
If you operate the device in 19” switch cabinet: install the slide / rails
to support the weight of the device.
 Installation site requirements
Operate the device at the specified ambient temperature (temperature
of the ambient air at a distance of 5 cm (2 in) from the device) and at
the specified relative humidity exclusively.
When you are selecting the installation location, confirm that you
observe the climatic threshold values specified in the technical data.
Use the device in an environment with a maximum pollution degree
that complies with the specifications in the technical data.

12
Installation MTS8003/8006/8010
Release 01 12/2021
 CE marking
The labeled devices comply with the regulations contained in the
following European directive(s):
 2011/65/EU and 2015/863/EU (RoHS)
Directive of the European Parliament and of the Council on the
restriction of the use of certain hazardous substances in electrical
and electronic device.
 2014/30/EU (EMC)
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to
electromagnetic compatibility.
 2014/35/EU
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to the
making available on the market of electrical equipment designed for
use within certain voltage limits.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
You find the EU conformity declaration as PDF file for downloading on
the Internet at: https://catalog.belden.com
Warning! This is a class A device. This device can cause interference
in living areas, and in this case the operator may be required to take
appropriate measures.
Warning! When Ethernet cables are used in industrial environments,
confirm that they are shielded.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

13
Installation MTS8003/8006/8010
Release 01 12/2021
 LED or laser components
LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCTS
CLASS 1 LED PRODUCTS
 FCC note
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
MTS8003/8006/8010
U.S. Contact Information
Belden – St. Louis
1 N. Brentwood Blvd. 15th Floor
St. Louis, Missouri 63105, United States
Phone: [phone]
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
 This device may not cause harmful interference, and
 This device must accept any interference received, including
interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a
class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against
interference with the device when used in commercial environments.
This device generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. Use of the
device in residential areas can also cause interference, in this case
the user is obliged to pay to eliminate such interference.

14
Installation MTS8003/8006/8010
Release 01 12/2021
 Recycling note
After usage, this device must be disposed of properly as electronic
waste, in accordance with the current disposal regulations of your
county, state, and country.

15
Installation MTS8003/8006/8010
Release 01 12/2021
About this manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that
you need to install the device.
Documentation mentioned in the “User Manual Installation” that is not
supplied with your device as a printout can be found as PDF files for
downloading on the Internet at: https://catalog.belden.com

16
Installation MTS8003/8006/8010
Release 01 12/2021
Key
The symbols used in this manual have the following meanings:
 Listing
Work step
 Subheading

17
Installation MTS8003/8006/8010
Release 01 12/2021
1. Description
1.1 General device description
MTS8000 series switch uses the main control and exchange separation
technology leading in the industry. The device provides the deployment
capability of at most 448 × 10 Gbit/s interfaces or 128 × 40 Gbit/s high-
density ports. Provide multiple physical resource virtualization technologies,
such as 1:N, N:1, raise the SDN compatible machine concept for the first
time, and realize the integration of SDN deployment with the functions of
common switch.
MTS8000 series switch meets the demand for the deployment scenario with
high throughput, and high-density and high-speed interface in the building of
new-generation data center. In combination with MTS2900 series switches,
can provide a comprehensive reliable solution and integrated new-
generation data centers in series for the building of the data center in the
financial sector, government, operator and energy industries.
 Basic devices
Figure 1: MTS8003- Chassis

18
Installation MTS8003/8006/8010
Release 01 12/2021
Figure 2: MTS8006- Chassis
Figure 3: MTS8010- Chassis

19
Installation MTS8003/8006/8010
Release 01 12/2021
 Power module
You can choose 1 to 4 power modules with the same input voltage:
Power modules are provided as accessories.See "Order Number" on
Page 80.
 Engine module
Engine module is the most important and necessary board card in
MTS8000 series switch, and serves as the control center of the device.
Every machine frame uses 1 engine module, and 2 modules can be
supported at the same time, thus realizing the working mode of 1:1
backup. Engine modules are provided as accessories.See "Order
Number" on Page 80.
Note: Engine module is inserted into MPU (Main Processing Unit) card
slot.

20
Installation MTS8003/8006/8010
Release 01 12/2021
 Fan module
Figure 4: MTM8003- FAN
The rear panel of the switch provides 4 fan slots and confirm that
minimum 2 fan modules are installed for normal operation of the system.
Fan modules are provided as accessories.See "Order Number" on
Page 80.
Figure 5: MTM8006- FAN
The rear panel of the switch provides 2 fan slots and confirm that
minimum 2 fan modules are installed for normal operation of the system.
Fan modules are provided as accessories.See "Order Number" on
Page 80.