Belden HIRSCHMANN MACH 1040 Series User manual

MACH 1040
Release 02 03/2013
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Ruggedized Switch
MACH 1040 Family Full Gigabit
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.24USB
P
FAULT
Sb R1
R2
RM
MAR1040
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.24USB
P
FAULT
Sb R1
R2
RM
MAR1040
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.24USB
P
FAULT
Sb R1
R2
RM
MAR1142
P
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.24USB
P
FAULT
Sb R1
R2
RM
MAR1140
MAR1040
MAR1042
MAR1140
MAR1142
P
MAR1140, MAR1142
P
FAULT
RM Stand by
R1 R2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 ETHERNET Service Port
X
-/N +/L
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A
P1
U:24/48VDC I:x.x/x.x A
X
- +P2
R1
Relay
R2
Relay
X
-/N +/L
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A
P1
U:24/48VDC I:x.x/x.x A
X
- +P2
R1
Relay
R2
Relay

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2013 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Deutschland
Tel.: [phone]
MACH 1040 039 724-002-02-0313 20.3.13

MACH 1040
Release 02 03/2013 3
Contents
Safety instructions 4
About this Manual 12
Legend 12
1 Device description 13
1.1 General device description 13
1.2 Description of the device variants 14
1.2.1 MAR1040-... with 16 Gigabit ports 15
1.2.2 MAR1042-... with 16 Gigabit ports and PoE 16
1.2.3 MAR1040-... with 16 Gigabit ports, ports on back 17
1.2.4 MAR1142-... with 16 Gigabit ports, ports on back
and PoE 18
1.2.5 PoE ports 19
1.2.6 Combo ports 19
1.2.7 Signal contact 20
1.3 Combination options 20
2 Assembly and start-up 23
2.1 Installing the device 23
2.1.1 Unpacking and checking 23
2.1.2 Installing the SFP modules (optional) 23
2.1.3 Connecting the power unit connections
for supply voltage and signal contact 24
2.1.4 Installing the device 28
2.1.5 Startup procedure 32
2.1.6 Connecting the data lines 32
2.2 Display elements 34
2.3 Basic set-up 37
2.4 Maintenance 39
2.5 Disassembling the device 40
3 Technical data 41
A Further Support 50

4MACH 1040
Release 02 03/2013
Safety instructions
Certified usage
The device may only be employed for the purposes described in the
catalog and technical description, and only in conjunction with external
devices and components recommended or
approved by the manufacturer. The product can only be operated cor-
rectly and safely if it is transported, stored, installed and assembled pro-
perly and correctly. Furthermore, it must be operated and serviced
carefully.
Supply voltage
Note: The supply voltage is electrically isolated from the housing.
For every supply voltage to be connected, make sure the following
requirements are met:
The voltage supply conforms to overvoltage category II.
The voltage supply has an easily accessible disconnecting device
(e.g. a switch or a plug).
The disconnecting device is clearly identified so that in the case of
an emergency, it is clear which disconnecting device belongs to
which line.
The lines to be connected are voltage-free.
The ground screw on the back of the device is connected to the
protective conductor.
There is a fuse in the outer conductor (AC) or the positive
conductor (DC) of the voltage supply.
Regarding the properties of this fuse: See „General technical data”
on page 41.
When using a DC voltage supply: the fuse is suitable for a DC
voltage.
If the neutral conductor (AC) or the negative conductor (DC) is not
grounded: there is a fuse on each of the two wires.
Supply with AC voltage: the wire diameter for the input supply line
is at least 0.75 mm² (North America: AWG18).
WARNING
ELECTRIC SHOCK
Only connect a supply voltage that corresponds to the type plate of your
device.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

MACH 1040
Release 02 03/2013 5
Supply with DC voltage: the wire diameter for the input supply line
is at least 1 mm² (North America: AWG16).
The cross-section of the protective conductor cable is the same
size as or bigger than the cross-section of the voltage supply
cables.
The connection cables used are permitted for the specified
temperature range.
Relevant for North America:
The power supply lines are made up of copper wire.
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
Use undamaged parts.
The device does not contain any service components. Internal fuses
are only triggered if there is a fault in the device. If the device is not
functioning correctly, or if it is damaged, switch off the voltage supply
and return the device to the plant for inspection.
Only switch on the device when the housing is closed.
First connect the ground screw on the back of the device with the
protective conductor before you set up the other connections. When
removing the connections, you remove the protective conductor last.
For voltage supply connections with a protective conductor
connection: first connect the protective conductor before connecting
the lines for the supply voltages.
If your device has a second voltage supply connection of this type:
here you also first connect the protective conductor before connecting
the lines for the supply voltages.
Shielding ground
The shielding ground of the connectable twisted pairs lines is connected
to the front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shielding braiding.
WARNING
ELECTRIC SHOCK
Only start connecting the supply voltage if all the above mentioned
requirements are fulfilled.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

6MACH 1040
Release 02 03/2013
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
The device is grounded via a ground connection on the front panel of the
device.
The ventilation slots must not be covered to promote free air
circulation.
The clearance to the ventilation slots of the housing must be at least
10 cm (3.94 in).
Do not touch the housing during operation or shortly after switching off
the device. Hot surfaces can cause injury.
The device must be installed in the horizontal or upright position, either
in the switch cabinet or on the wall (see page 28 „Installing the
device“). The device is not intended for operation as a table unit.
Operating the device in the maximum surrounding air temperature and
stacking devices: When installing the device, make sure there is at
least one free rack space (approx. 5 cm) above the device, because
heat is discharged via the housing of the device.
If you are operating the device in a 19" switch cabinet: install sliding/
mounting rails for holding the device (see fig. 10).
WARNING
ELECTRIC SHOCK
Never insert any pointed objects (small screwdrivers, wires, etc.) into the
product!
Never insert sharp objects (small screwdrivers, wires, etc.) into the
connection terminals for the supply voltage or the signal contact, and do not
touch the terminals!
Only install this device in a switch cabinet or in an operating site with limited
access, to which only maintenance staff have access.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.
WARNING
FIRE HAZARD
Install the device in a fire protected shell if you are mounting it vertically.
Failure to follow these instructions can result in death, serious injury,
or equipment damage.

MACH 1040
Release 02 03/2013 7
Environment
The device may only be operated at the specified surrounding air
temperature (temperature of the surrounding air at a distance of up to
5 cm (1.97 in) from the device) and relative air humidity specified in the
technical data.
Install the device in a location where the climatic threshold values
specified in the technical data will be observed.
Use the device only in an environment within the pollution degree
specified in the technical data.
Relevant for use in Hazardous Locations (Class 1, Division 2):
This equipment is suitable for use in Class 1, Division 2, Groups A, B, C
and D or Non-Hazardous (unclassified) locations only.
When used in Class 1 Division 2 Hazardous Locations, the following
applies:
CLASS I; DIV. 2
GROUPS A; B; C AND D
TEMPERATURE CODE T4
AMBIENT -30 °C ... +70 °C
List of Standards: ISA 12.12.01:2007, CSA C22.2 No. 213-
M1987
This equipmnt must be installed in a tool-locked enclosure when the USB
port will be used.
Warning: Do not remove or replace while circuit is live unless
the area is known to be free of ignitable concentrations or
flammable substances.

8MACH 1040
Release 02 03/2013
Figure 1: Control Drawing 000154226DNR
For use in Hazardous Locations according ISA12.12.01-2007 Class I Div. 2 Groups A, B, C, D
Control Drawing MACH1040-Family
Hazardous Location
ACA21-USB
Auto
Configuration
Adapter
For maintenance
only – See
Installation
Instructions
V.24 Interface
(External
management)
Data
communication
Ethernet Ports
Power Supply 1
L: 24VDC to 48VDC
M: 100VAC to
240VAC 50/60Hz
Power Supply 2
9: Not present
L: 24VDC to 48VDC
M: 100VAC to
240VAC 50/60Hz
Signal Contacts
(On: O.K.
Open: fault)
Associated
Apparatus:
Equipment with
nonincendive
field wiring
parameters
Ordinary Location - Non-Hazardous Area
The Use in Hazardous Locations is only allowed for MACH1040-Family model No´s which are individually labelled “FOR
USE IN CLASS I, DIVISION 2 HAZARDOUS LOCATIONS”
Notes:
The nonincendive field wiring circuit concept allows interconnection of nonincendive field wiring apparatus and associated
nonincendive field wiring apparatus using any of the wiring methods permitted for unclassified locations when certain
parametric conditions are met.
Capacity: C
a
C
i
+ C
Cable
Inductivity: L
a
L
i
+ L
Cable
The maximum cable length has to be determined as follows:
(a) max. Cable Length < (L
a
-L
i
) / Cable
L
and (b) max. Cable Length < (C
a
-C
i
) / Cable
C
The lower value of (a) and (b) is to apply.
Cable
L
: inductance per unit length of used cable.
Cable
C
: capacitance per unit length of used cable.
Other C-parameters and L-parameters are according to ANSI / ISA 12.12.01 2007 section 7.
Where cable capacitance and inductance values are unavailable, use the following default values: 60pF/foot (200pF/m),
0.2uH/foot (0,7uH/m)
Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC), NFPA 70 , article
501.
Vmax Imax Ci Li
The Relay Terminals are dependent upon the following Entity
Parameters: 30V 90mA 50pF 2µH
The MACH1040-Family is an open type which must be installed within an enclosure appropriate for
environmental protection.
WARNING - Explosion Hazard – Do not disconnect Equipment while the circuit is live or unless the area
is known to be free of ignitable concentrations.
WARNING – Explosion Hazard – Substitution of any component may impair suitability for Class I,
Division 2.
Do not open when energized.
CONTROL DRAWING for Full Gigabit Ethernet Switch
MACH1040 Family
according to ANSI / ISA-12.12.01 – 2007
Rev.: 2 Date: 2011-03-18 Document No.: 000154226DNR Page 1 of 1

MACH 1040
Release 02 03/2013 9
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.
General safety instructions
Electricity is used to operate this equipment. Comply with every detail of
the safety requirements specified in the operating instructions regarding
the voltages to apply.
Non-observance of these safety instructions can therefore cause material
damage and/or injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. These personnel must be thoroughly familiar with the
warnings and maintenance procedures in accordance with this
operating manual.
The proper and safe operation of this device depends on proper
handling during transport, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operation with damaged components.
Only use the devices in accordance with this manual. In particular,
observe the warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Please note that products recommended as accessories may have
characteristics that do not fully correspond to those of the
corresponding product. This may limit their possible usage in the
overall system.
Note: LED or LASER components in compliance with IEC 60825-1
(2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

10 MACH 1040
Release 02 03/2013
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
CE marking
The devices comply with the regulations contained in the following
European directive(s):
2004/108/EC
Directive of the European Parliament and the council for standardizing
the regulations of member states with regard to electromagnetic
compatibility.
2006/95/EC
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electrical equipment to be
used within specific voltage ranges.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2:2005
Emitted interference: EN 55022:2010
Safety: EN 60950-1:2006 + A11:2009 + A1:2010
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.

MACH 1040
Release 02 03/2013 11
FCC note:
This device complies with part 15 of FCC rules. Operation is subject to the
following two conditions : (1) This device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can radiate same, and
if it is not installed and used in accordance with this operating manual, it
can cause radio transmission interference. The use of this device in a
living area can also cause interference, and in this case the user is
obliged to cover the costs of removing the interference.
Recycling note
After usage, this product must be disposed of properly as electronic
waste, in accordance with the current disposal regulations of your county,
state and country.

12 MACH 1040
Release 02 03/2013
About this Manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD-ROM supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Router Configuration user manual
Graphical User Interface reference manual
Command Line Interface user manual
The Industrial HiVision Network Management Software provides you with
additional options for smooth configuration and monitoring:
Simultaneous configuration of multiple devices
Graphic interface with network layout
Auto-topology discovery
Event log
Event handling
Client/server structure
Browser interface
ActiveX control for SCADA integration
SNMP/OPC gateway.
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

MACH 1040
Release 02 03/2013 13
1 Device description
1.1 General device description
The MACH 1040 family provides you with a range of device variants. You can
set up your device individually based on different criteria:
Media type
Temperature range
Voltage range
Software variant
The MACH 1040 devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
long-term reliability and flexibility.
The devices allow you to set up switched industrial Ethernet networks that
conform to the IEEE 802.3 standard using copper wires or optical fibers in a
line or ring structure.
The devices work without a fan.
If required, the devices are PoE-capable.
For devices without PoE, the voltage supply can be redundant if required.
The following installation options are available:
19" switch cabinet
Flat surface mounting
You can choose various media to connect terminal devices and other
infrastructure components:
twisted pair cable
multimode F/O
singlemode F/O
The ring redundancy concept allows the network to be reconfigured quickly
after a failure.
Product configuration data can be provided by:
diagnosis displays
displaying the operating parameters
There are convenient options for managing the device. Administer your
devices via:
a Web browser
Telnet
HiDiscovery (software for setting up operation of the device)

14 MACH 1040
Release 02 03/2013
management software (e.g. Industrial HiVision)
a V.24 interface (locally on the Switch)
The devices provide you with a large range of functions, which the manuals
for the operating software inform you about. These manuals are available as
PDF files on the CD ROM provided, or you can download them from the
Internet on the Hirschmann product pages (www.hirschmann.com).
The Hirschmann network components help you ensure continuous
communication across all levels of the company.
1.2 Description of the device variants
The MACH 1040 devices are Ruggedized Switches with 16 Gigabit
ETHERNET ports (10/100/1000 Mbit/s, can be connected optically or with
TX). These ports are suitable for the connection of terminal devices or
network segments according to the standards IEEE 802.3 100/
1000BASE-FX (SFP slot) and IEEE 802.3 1000BASE-T / 100BASE-TX /
10BASE-T (RJ45 socket). A plugged SFP module switches the TX port
off.
In the MAR1140... and MAR1142... devices, all the cable outlets are at the
back, i.e. the ports are on the back of the device. They have an additional
Fast Ethernet port on the front of the device that you can use for diagnosis
purposes.
The MAR1042... and MAR1142... devices support PoE (Power over
Ethernet) in accordance with IEEE 802.3af. The PoE ports are the Gigabit
Ethernet ports 1 to 4.

MACH 1040
Release 02 03/2013 15
1.2.1 MAR1040-... with 16 Gigabit ports
Figure 2: 1 - MAR1040 device
2 - LED display elements
3 - USB interface
4 - V.24 connection for external management
5 - Gigabit Ethernet combo ports: 100/1000 Mbit/s fiber optic
SFP slots. Alternative connections: 10/100/1000 Mbit/s twisted pair, RJ45
connections
Back of device:
6 - P1: Connection for the voltage supply
7 - Relay 1: signal contact
Back of device for device variants with 2 power supply units:
8 - P2: Connection for redundant voltage supply
9 - Relay 2: signal contact
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.2 4USB
P
FAULT
Sb R1
R2
RM
MAR1040
X
-/N +/L
R2R1
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A U:24/48VDC I:x.x/x.x A
X
- +
P1 P2
Relay Relay
U: 110 / 230 V AC 50HZ / 60HZ I: x.xx / x.xx A
(U : 90 - 265 V AC)
or
U: 110 / 250 V DC I: x.xx / x.xx A
(U : 77 - 300 V DC)
U: 24 / 48 V DC I: x.x / x.x A
(U : 18 - 60 V DC)
R1/R2 - Relay:
2A @ 30V DC
0,2A @ 125V DC
0,1A @ 250V DC
2A @ 230V AC
P1: P2:
in
in
in
X
-/N +/L
R2R1
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A U:24/48VDC I:x.x/x.x A
X
- +
P1 P2
Relay Relay
U: 110 / 230 V AC 50HZ / 60HZ I: x.xx / x.xx A
(U : 90 - 265 V AC)
or
U: 110 / 250 V DC I: x.xx / x.xx A
(U : 77 - 300 V DC)
R1/R2 - Relay:
2A @ 30V DC
0,2A @ 125V DC
0,1A @ 250V DC
2A @ 230V AC
P1:
in
in
13 57 911 1315
2 4 6 8 10 12 14 16
6 7 8 9
6 7
2 3 41
55 5 5

16 MACH 1040
Release 02 03/2013
1.2.2 MAR1042-... with 16 Gigabit ports and PoE
Figure 3: 1 - MAR1042 device
2 - LED display elements
3 - USB interface
4 - V.24 connection for external management
5 - Gigabit Ethernet combo ports with Power over Ethernet (PoE): 100/
1000 Mbit/s fiber optic SFP slots. Alternative connections: 10/100/1000
Mbit/s twisted pair, RJ45 connections
6 - Gigabit Ethernet combo ports: 100/1000 Mbit/s fiber optic
SFP slots. Alternative connections: 10/100/1000 Mbit/s twisted pair, RJ45
connections
Back of device:
7 - P1: Connection for the voltage supply
8 - Relay 1: signal contact
Back of device for device variants with 2 power supply units:
9 - P2: Connection for the PoE voltage supply
10 - Relay 2: signal contact
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.2 4USB
P
FAULT
Sb R1
R2
RM
MAR1042
P
X
-/N +/L
R2R1
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A U:24/48VDC I:x.x/x.x A
X
- +
P1 P2
Relay Relay
U: 110 / 230 V AC 50HZ / 60HZ I: x.xx / x.xx A
(U : 90 - 265 V AC)
or
U: 110 / 250 V DC I: x.xx / x.xx A
(U : 77 - 300 V DC)
U: 24 / 48 V DC I: x.x / x.x A
(U : 18 - 60 V DC)
R1/R2 - Relay:
2A @ 30V DC
0,2A @ 125V DC
0,1A @ 250V DC
2A @ 230V AC
P1: P2:
in
in
in
X
-/N +/L
R2R1
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A U:24/48VDC I:x.x/x.x A
X
- +
P1 P2
Relay Relay
U: 110 / 230 V AC 50HZ / 60HZ I: x.xx / x.xx A
(U : 90 - 265 V AC)
or
U: 110 / 250 V DC I: x.xx / x.xx A
(U : 77 - 300 V DC)
R1/R2 - Relay:
2A @ 30V DC
0,2A @ 125V DC
0,1A @ 250V DC
2A @ 230V AC
P1:
in
in
13 57 911 1315
2 4 6 8 10 12 14 16
7 8 9 10
7 8
2 3 41
65 6 6

MACH 1040
Release 02 03/2013 17
1.2.3 MAR1040-... with 16 Gigabit ports, ports on back
Figure 4: Back of device:
1 - MAR1140 device
2 - LED display elements
3 - USB interface
4 - V.24 connection for external management
5 - Gigabit Ethernet combo ports: 100/1000 Mbit/s fiber optic
SFP slots. Alternative connections: 10/100/1000 Mbit/s twisted pair, RJ45
connections
6 - P1: Connection for the voltage supply
7 - Relay 1: signal contact
For device variants with 2 power supply units:
8 - P2: Connection for redundant voltage supply
9 - Relay 2: signal contact
Front of device:
10 - LED device status display elements
11 - LED port status display elements
12 – LED service port display element
13 - Service port
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.2 4USB
P
FAULT
Sb R1
R2
RM
MAR1140
P
FAULT
RM Stand by
R1 R2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 ETHERNET Service Port
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.2 4USB
P
FAULT
Sb R1
R2
RM
MAR1140
FAULTFAULT
X-/N +/L
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A
P1
R1
Relay
X-/N +/L
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A
P1
U:24/48VDC I:x.x/x.x A
X- +P2
R1
Relay
R2
Relay
13 57 911 1315
2 4 6 8 10 12 14 16
13 57 911 1315
2 4 6 8 10 12 14 16
10 11 12 13
6 8 9 7
6 7
2 3 41
55 5 5
23 41
55 5 5

18 MACH 1040
Release 02 03/2013
1.2.4 MAR1142-... with 16 Gigabit ports, ports on back
and PoE
Figure 5: Back of device:
1 - MAR1142 device
2 - LED display elements
3 - USB interface
4 - V.24 connection for external management
5 - Gigabit Ethernet combo ports with Power over Ethernet (PoE): 100/
1000 Mbit/s fiber optic SFP slots. Alternative connections: 10/100/1000
Mbit/s twisted pair, RJ45 connections
6 - Gigabit Ethernet combo ports: 100/1000 Mbit/s fiber optic
SFP slots. Alternative connections: 10/100/1000 Mbit/s twisted pair, RJ45
connections
7 - P1: Connection for the voltage supply
8 - Relay 1: signal contact
For device variants with 2 power supply units:
9 - P2: Connection for redundant voltage supply
10 - Relay 2: signal contact
Front of device:
11 - LED device status display elements
12 - LED port status display elements
13 - LED service port display element
14 - Service port
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.2 4USB
P
FAULT
Sb R1
R2
RM
MAR1140
P
FAULT
RM Stand by
R1 R2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 ETHERNET Service Port
Aufkleber MAC-Adresse
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V.2 4USB
P
FAULT
Sb R1
R2
RM
MAR1140
FAULTFAULT
X-/N +/L
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A
P1
R1
Relay
X-/N +/L
U:110/230VAC 50HZ/60HZ I:x.x/x.xA
U:110/250VDC
I:x.x/x.x A
P1
U:24/48VDC I:x.x/x.x A
X- +P2
R1
Relay
R2
Relay
13 57 911 1315
2 4 6 8 10 12 14 16
13 57 911 1315
2 4 6 8 10 12 14 16
P
P
11 12 13 14
7 9 10 8
7 8
2 3 41
65 6 6
23 41
65 6 6

MACH 1040
Release 02 03/2013 19
The device variants of the MACH 1040 with ports on the rear panel
have the following characteristics:
The display LEDs are on the front of the device. There are 16 LEDs for
displaying the status of the Gigabit Ethernet ports and 6 LEDs for
displaying the device status.
The supply voltage connection and the ports are on the back of the
device. The device has 16 Gigabit Ethernet ports and an additional Fast
Ethernet port on the front of the device that you can use for diagnosis
purposes.
1.2.5 PoE ports
The MAR1042/MAR1142 device variants support Power over Ethernet (PoE)
in accordance with IEEE 802.3af.
They allow the connection and remote supply of, for example, IP telephones
(Voice over IP), webcams, sensors, printer servers and WLAN access points
via 10BASE-T/100BASE-TX/1000BASE-T. With PoE, these terminal devices
are powered by the twisted-pair cable.
The MAR1042 and MAR1142 provide four 10BASE-T/100BASE-TX/
1000BASE-T ports (RJ45 sockets) for connecting network segments or PoE
terminal devices (PD, Powered Device) for all IEEE802.3af classes up to a
maximum power output of 15.4 W.
The 4 PoE-capable ports are the 4 first ports on the device (ports 1 to 4, see
fig. 3 and fig. 5). The PoE ports are indicated with the red PoE logo on the
device.
The current is supplied on wire pairs transmitting the signal; the individual
ports are not electrically insulated from each other.
(see page 32 „10/100/1000 Mbit/s twisted pair connection“)
The following conditions are met in accordance with IEEE 802.3af:
Endpoint PSE
Alternative A
1.2.6 Combo ports
At the four Gigabit Ethernet combo ports (see fig. 2 to fig. 5) you can
connected either F/O (via SFP modules) or twisted pair.
SFP modules
SFP modules are optical transceivers (Fast ETHERNET and Gigabit
ETHERNET SFP modules, see page 48 „Accessories“). SFP stands for
Small Form-factor Pluggable and is also frequently referred to as mini-
GBIC (GigaBit Interface Converter).

20 MACH 1040
Release 02 03/2013
The SFP modules are plugged into the SFP slots of the MACH 1040
device in order to obtain an F/O port. The MACH 1040 has 16 TP
interfaces and 16 slots for inserting SFP modules (100/1000 Mbit/s).
By inserting the SFP module you deactivate the corresponding TP
interface.
Note: Only use Hirschmann SFP modules (see page 48 „Accessories“).
1.2.7 Signal contact
Depending on the MACH 1040 device variant (equipped with one or two
power units), you have either one or two signal contacts.
The signal contact monitors proper functioning of the device, thus
enabling remote diagnostics. You can specify the type of function
monitoring in the Management.
You can also use the Management to switch the signal contact manually
and thus control external devices.
A break in contact is used to report the following conditions via the potential-
free signal contact (relay contact, closed circuit):
The failure of at least one supply voltage.
The device is not operational.
The loss of connection at at least one port. The report of the link status
can be masked by the Management for each port. In the delivery state,
link status monitoring is deactivated.
The loss of ring redundancy reserve.
A detected error during the self-test.
Incorrect configuration of the HIPER-Ring or ring coupling.
Permitted temperature range exceeded/not reached.
The following condition is also reported in RM mode:
Ring redundancy reserve is available. On delivery, there is no ring
redundancy monitoring.
Note: You can use the signal contact functions when the voltage supply is
connected. If there is redundant voltage supply, but this is turned off, there is
a contact interruption at the corresponding signal contact.
1.3 Combination options
The product designation of your device is made from combining the desired
product characteristics in accordance with the following table. The
corresponding short designation is in column 3.