Belkin OmniView PRO2 Rack User manual

User Manual
Manuel de l’utilisateur
Benutzerhandbuch
Handleiding
Manual del usuario
Manuale d’uso
F1DC108Tea
F1DC116Tea
OmniView® PRO2 Rack
Console with KVM Switch

User Manual
F1DC108Tea
F1DC116Tea
OmniView® PRO2 Rack
Console with KVM Switch

Table of Contents
1. Introduction ................................................................................... 1
Package Contents .......................................................................... 1
2. Overview ........................................................................................ 2
Feature Overview ........................................................................... 2
Equipment Requirements ............................................................... 4
System Requirements .................................................................... 5
Specifications ................................................................................. 6
Unit Display Diagrams .................................................................... 7
3. Installation ..................................................................................... 8
Pre-Configuration ........................................................................... 8
Mounting the Console .................................................................... 9
Connecting Servers to the Console .............................................. 11
Daisy-Chaining Multiple KVM Switches ........................................ 13
Powering Up the Systems ............................................................ 17
4. Using the Console ........................................................................ 18
Selecting a Server or BANK Using Hot-Key Commands .............. 18
AutoScan Mode ........................................................................... 20
On-Screen Display ....................................................................... 21
Hot-Key-Command Shortcuts ...................................................... 24
Updating Firmware ....................................................................... 24
5. Frequently Asked Questions ....................................................... 25
6. Troubleshooting ........................................................................... 26
7. Glossary ....................................................................................... 28
8. Certification & Warranty Information .......................................... 29

5
Introduction
Congratulations and thank you for purchasing the Belkin OmniView PRO2 Rack
Console with KVM Switch (the Console). This product allows network administrators
to conveniently control up to 16 PS/2- or USB-platform servers from a single,
compact, rack-mount console. The Console provides easy and dependable control,
and features a built-in PRO2 KVM Switch, the industry’s most popular KVM switch for
small-to-medium-size businesses.
This User Manual provides all the details you’ll need to install and operate your new
Console, in addition to expert troubleshooting advice—in the unlikely event of a
problem. For quick and easy installation, please refer to the Quick Installation Guide
included in your packaging.
We appreciate your business and are confident that you will soon see for yourself why
Belkin OmniView products are the number-one-selling KVM products worldwide.
Package Contents
OmniView PRO2
Rack Console
with KVM Switch
Quick
Installation Guide
IEC Power Cable
Schuko and UK plug User Manual
Adjustable Brackets Front Mounting
Brackets

6
section
Feature Overview
Dual-Rail System
The Console features independently sliding rails that allow the LCD panel to remain
displayed, even when the keyboard is stored and the server-rack door is closed.
Premium 17” LCD Panel
The Console features a premium-grade, 17-inch LCD with a protected, tempered-
glass overlay. The LCD panel can rotate up to 105 degrees for easy monitoring.
Built-In PRO2 KVM Switch
The Console comes with a built-in OmniView PRO2 8- or 16-Port KVM Switch, the
industry’s most popular KVM switch for small-to-medium-size server rooms.
Daisy-Chain Expansion
The Console can easily be daisy-chained with up to 15 additional OmniView PRO2
KVM Switches to support up to 256 servers. A dedicated daisy-chain port allows you
to easily expand your KVM configuration, without sacrificing any of your available CPU
ports.
Multi-Platform Support
The Console supports PS/2- and USB-platform servers, including Windows®, Mac
OS®, and UNIX®/Linux®.
Micro-Cabling Technology
Servers can be connected to the Console using Belkin’s Dual-Port Micro-Cabling.
With 60-percent reduction in cable bulk, Micro-Cabling simplifies deployment and
allows for greater airflow in your racks, increasing the life span of your equipment.
On-Screen Display (OSD)
The built-in KVM Switch features an OSD that simplifies server management. The OSD
allows you to assign names to each connected server, and provides a visual means of
switching between servers.
Overview
1
2
3
4
5
6
7
8

7
Video Resolution
The Console supports high video resolutions of up to 1280x1024 (SXGA).
1U Rack-Mount Installation
With its compact design, the Console can be mounted to a standard 19-inch server
rack for 1U installation.
Low-Extension Drawer Handles
The two drawer handles conveniently fold down to extend only 0.5 inches (13mm)
from the front of the Console, allowing you to store the Console with the rack door
securely closed.
Adjustable Brackets
With two adjustable brackets, the Console can be easily installed in any server rack
with rail depths between 26.5 inches and 31.5 inches (673mm and 800mm).
Rugged Enclosure
The Console is protected by a heavy-duty steel enclosure to extend the operating life
of the product.
Hot Keys
Hot-key functionality allows you to select a desired port using designated key
commands. By using a simple hot-key sequence on your keyboard, you can select
one server from as many as 256 servers, instantaneously.
AutoScan
The AutoScan feature allows you to set the Console to scan and monitor the activities
of all connected servers, one by one. The time interval allotted for each server can be
adjusted through the OSD menu.
Firmware Updates
USB flash upgrades allow you to obtain the latest firmware updates for your Console.
These firmware updates ensure that the Console is compatible with the latest devices
and hardware, and are free for the life of the Console. Visit www.belkin.com for
upgrade information and support.
Overview

8
1
2
3
4
5
6
7
8
section
8
Equipment Requirements
Cables
Connecting the Console to servers requires
custom Belkin Dual-Port Micro-Cable
Kits. These cables offer the highest quality
possible to ensure optimal data and video
transmission. One Cable Kit is required for
every two connected servers.
Dual-Port Micro-Cable Kit:
F1D9400-XX (PS/2 style)
F1D9401-XX (USB style)
To connect the Console with multiple KVM
switches (daisy-chain), a custom Belkin
OmniView Daisy-Chain Cable is required.
OmniView Daisy-Chain Cable:
F1D108-CBL
Sun Adapter
The Belkin Universal Sun Adapter is
required to connect Sun™ servers to the
Console. One Adapter is required per
server.
Universal Sun Adapter:
F1DE083ea
F1DE083uk (Only for the Uk version)
Note:
Product codes and availability may vary.
F1D108-CBL
F1D9401-XX (USB)
F1DE083ea/F1DE083uk
Overview

9
Overview
System Requirements
Operating-System (OS) Platforms
The Console is compatible with CPUs running on, but not limited to, the following OS
platforms:
• Windows® NT®, 2000, XP, Server 2003
• Microsoft® DOS 5.x and above
• Red Hat® Linux® 8.x and above
• Mac OS® X v10.x and above
• Novell® NetWare® 4.x/5.x

10
1
2
3
4
5
6
7
8
section
Overview
Specifications
Part No.: F1DC108Txx, F1DC116Txx
No. of Users Supported: 1
No. of Servers Supported: 8 and 16 respectively for 8- and 16-port models
Max. No. of Servers Supported: 248 and 256 respectively for 8- and 16-port models
(via daisy-chaining)
Daisy-Chain: Maximum of 16 Switches*
Enclosure: Metal enclosure
Power Requirements: 100–240VAC @ 50–60Hz
Operating Temp: 32° to 104° F (0° to 40° C)
Storage Temp: -4° to 140° F (-20° to 60° C)
Humidity: 0-80% RH, non-condensing
Video Resolution: Up to 1280x1024 (SXGA)
Keyboard Emulation: PS/2
Mouse Emulation: PS/2
Keyboard Type: 106-key, PS/2-compatible
Mouse Type: PS/2-compatible touch pad
CPU Ports: 4 and 8 respectively for 8- and 16-port models
CPU Port Type: High-density, 50-pin, SCSI 2-style connector**
Optional Console Ports: HDDB15 (VGA), miniDIN6 (PS/2)
Flash-Upgrade Port: Mini-USB
Rack-Rail-Depth Support: 26.5 to 31.5 in. (673 to 800mm)
Drawer-Handle Extension: 0.5 in. (13mm)
Warranty: 2 years
Dimensions: (F1DC108Txx) 17.5 (W) x 1.75 (H) x 22.5 (L) in. (445 x 45 x 572mm)
(F1DC116Txx) 17.5 (W) x 1.75 (H) x 22.5 (L) in. (445 x 45 x 572mm)
Weight: (F1DC108Txx) 26.5 lbs. (12.0kg.)
(F1DC116Txx) 26.5 lbs. (12.0kg.)
*May be daisy-chained with up to 15 additional OmniView PRO2 KVM Switches.
**Requires Belkin Dual-Port Micro-Cable Kit.

1111
Overview
50~60Hz


FLASH











Unit Display Diagrams
Front View
Dedicated Daisy-Chain Port
DIP Switch
AC Power CPU Connections Using Micro-Cabling
Flash-Upgrade
Port
Optional Console Port
Back View
LCD-Panel
Handle
17" LCD
Mouse Touch
Pad
Keyboard-Drawer
Handle
Front Brackets
LCD-Display Buttons
Adjustable Brackets
Key Lock
Keyboard

12
1
2
3
4
5
6
7
8
section
Note: Specifications are subject to change without notice.
Pre-Configuration
Where to place the Console:
The enclosure of the Console is designed for rack-mount configuration in a standard
19-inch server rack. Rack-mount hardware is included for a sturdy rack installation.
Consider the following when deciding where to place the
Console:
• the depth of your rack or enclosure
• the location of your servers in relation to your console
• how far your servers extend forward from your front rack rails
• the lengths of the cables you use to connect your servers to the Console
• whether you intend to daisy-chain the Console with other KVM switches
(you will need to set the “BANK DIP” switch before mounting—refer to page 13)
Cable-Distance Requirements
For best video performance, we recommend that the cable length from the Console to
your servers be limited to 25 feet (8m) for PS/2 connections, and 12 feet (4m) for USB
connections. Beyond that length, the probability of video degradation increases.
Warning: Avoid placing cables near fluorescent lights, air-conditioning
equipment, or machines that create electrical noise (e.g., vacuum cleaners)
Consider the following before mounting the Console:
a) Elevated Operating Ambient Temperature—If installed in a closed or multi-unit
rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient. Therefore, you should consider installing
the equipment in an environment compatible with the rack manufacturer’s
maximum-rate ambient temperature.
b) Reduced Airflow—Installation of the equipment in a rack should be such
that the amount of airflow required for safe operation of the equipment is not
compromised.
c) Mechanical Loading—Mounting of the equipment in the rack should be such
that hazardous condition is not achieved due to uneven mechanical loading.
d) Reliable Grounding—Grounding of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections other
than direct connections to the branch circuit.
Installation

13
Installation
Step 1 Mounting the Console
The Console comes with brackets already attached for mounting the front of the
Console to your rack or enclosure. These brackets allow for maximum rotation of
the LCD panel when displayed. Your packaging includes two alternate sets of front
mounting brackets. Choose the brackets that will give you the desired clearance from
the front rails of your rack or enclosure.
The Console also includes two brackets for mounting the back of the Console, which
can be adjusted to fit the depth of your rack or enclosure.
1.1 Choose the desired front bracket length. Replace the brackets on the front of
the Console, if necessary. (Refer to diagram below.)
1.2 Insert the rear rack-mount brackets into the side rails of the Console.
(Refer to diagram below.)

14
1
2
3
4
5
6
7
8
section
Installation
1.3 Mount the Console to your rack or enclosure. (Refer to diagram below.)
1.4 Attach the power cable to the back of the Console and connect to a power
source. Do not power up the Console at this time. (Refer to diagram below.)
Your Console is now mounted securely to the rack and you are ready
to connect your servers.
50~60Hz


FLASH









 

151515
Installation
Step 2A Connecting Servers to the Console
(PS/2 Connection)
2A.1 Make sure your servers are powered off.
2A.2 Using the Belkin PS/2 Dual-Port Micro-Cable Kit (F1D9400-XX), connect the 50-
pin, SCSI 2-style connector to the back of the Console in the port labelled “Port
01/02” or next available port. (Refer to diagram below.)
2A.3 Connect the VGA and PS/2 connectors to the monitor, keyboard, and mouse
ports on the first server. Do not power up the server at this time. (Refer to
diagram below.)
2A.4 Connect the other VGA and PS/2 connectors to the monitor, keyboard, and
mouse ports on the second server. Do not power up the server at this time.
2A.5 Repeat steps 2A.2 through 2A.4 for each additional PS/2 server you wish to
connect.
50~60Hz


FLASH









 
Server
Console

16
1
2
3
4
5
6
7
8
section
Installation
Step 2B Connecting Servers to the Console
(USB Connection)
2B.1 Make sure your servers are powered off.
2B.2 Using the Belkin USB Dual-Port Micro-Cable Kit (F1D9401-XX), connect the 50-
pin, SCSI 2-style connector to the back of the Console in the port labelled “Port
01/02” or next available port. (Refer to diagram below.)
2B.3 Connect the VGA and USB connectors to the monitor port and an available
USB port on the first server. Do not power up the server at this time.
(Refer to diagram below.)
Console
Server
50~60Hz


FLASH









 
2B.4 Connect the other VGA and USB connectors to the monitor port and an
available USB port on the second server. Do not power up the server at
this time.
2B.5 Repeat steps 2B.2 through 2B.4 for each additional USB server you
wish to connect.

17
Installation
Step 3 Daisy-Chaining Multiple KVM Switches (Optional)
You can daisy-chain up to 15 KVM switches to your Console, allowing you to control
up to a maximum of 256 servers from the Console. The following section provides
instructions for setting up your daisy-chain configuration. If you do not wish to daisy-
chain any KVM switches at this time, please skip to the “Powering Up the Systems”
section on page 17.
Each daisy-chained KVM switch is referred to as a “BANK” and is assigned an
address. The Console’s built-in KVM switch is BANK 00 and is referred to as the
“primary” KVM switch. BANKs 01 through 15 are referred to as “secondary” KVM
switches.
Note: Your PRO2 Rack Console is compatible with Belkin OmniView PRO2 KVM
Switches. You can daisy-chain any combination of up to 15 additional PRO2
KVM Switches to your Console.
Note: A Daisy-Chain Cable (F1D108-CBL) is required to daisy-chain each KVM
switch and is available through your Belkin reseller, or online at www.belkin.com
(U.S. only).
How to Assign a BANK Address
All OmniView PRO2 KVM Switches feature a “BANK DIP” switch. The “BANK DIP”
switch is used to assign the proper BANK address to each KVM Switch.
• For a single-unit configuration, set the “BANK DIP” switch on the KVM Switch
to the “primary” (BANK address 00) setting. This is the factory default setting.
• For a multi-unit configuration, the “BANK DIP” switch on the primary KVM switch
must be set to “BANK address 00”. Each secondary unit must be set to a unique
BANK address (from 01 through 15). Refer to the chart on page 14 or “BANK DIP”
switch settings.

18
1
2
3
4
5
6
7
8
section
Installation
BANK-DIP-Switch-Configuration Chart
DIP SWITCH# BANK ADDRESS
1234
Down Down Down Down BANK 00 Primary
(Default)
Up Down Down Down BANK 01 Secondary
Down Up Down Down BANK 02 Secondary
Up Up Down Down BANK 03 Secondary
Down Down Up Down BANK 04 Secondary
Up Down Up Down BANK 05 Secondary
Down Up Up Down BANK 06 Secondary
Up Up Up Down BANK 07 Secondary
Down Down Down Up BANK 08 Secondary
Up Down Down Up BANK 09 Secondary
Down Up Down Up BANK 10 Secondary
Up Up Down Up BANK 11 Secondary
Down Down Up Up BANK 12 Secondary
Up Down Up Up BANK 13 Secondary
Down Up Up Up BANK 14 Secondary
Up Up Up Up BANK 15 Secondary

19
Installation
Example of Daisy-Chain Configuration
One PRO2 Rack Console with 8-Port KVM Switch is daisy-chained with three PRO2
8-Port KVM Switches to manage up to 32 servers (see diagram below). The DIP switch
on the Console is set to “BANK 00” (factory default) and the secondary units are each
set to a unique BANK (between 01 and 03).
3.1 Make sure that the Console and all servers and KVM switches are powered
off and that each KVM switch has been assigned a unique BANK address.
3.2. Place the Console and secondary KVM switches in the desired location.
Connecting the primary and secondary KVM switches:
3.3 Using the Daisy-Chain Cable (F1D108-CBL), connect one end to the
“Primary Input/Secondary Output” port on the Console (BANK 00).
3.4 Connect the other end of the Daisy-Chain Cable (F1D108-CBL) to the “Primary
Input/Secondary Output” port of the first secondary KVM switch (BANK 01).
3.5 To add secondary units, connect one end of the Daisy-Chain Cable (F1D108-
CBL) to the “Secondary Input” on the first secondary KVM switch and the other
end to the “Primary Input/Secondary Output” port of the next secondary KVM
switch (for example, BANK 01).
3.6 Repeat step 3.5 for additional KVM switches you wish to daisy-chain together.
50~60Hz


FLASH


 
       




   



 
 


 
 


 
 

 


       




   



 
 


 
 


 
 

 


       




   



 
 


 
 


 
 

 


PRO2 Rack Console (BANK 00)
Secondary KVM Switch (BANK 01)
Secondary KVM Switch (BANK 02)
Secondary KVM Switch (BANK 03)

20
1
2
3
4
5
6
7
8
section
Installation
Connecting the servers:
3.7 Connect all servers to the Console and secondary KVM switches.
Refer to the “Connecting Servers to the Console” section on page 11
for instructions.
3.8 Make sure that the power cable is connected to the Console and that the
Console is powered on.
3.9 Power up the secondary KVM switches sequentially, beginning with BANK 01,
by connecting each unit’s power supply. Each KVM switch should display its
corresponding BANK address number as it is powered up.
Note: If the KVM switches do not enumerate correctly, recycle the power on
the Console to detect newly added secondary KVM switches. If the KVM
switches still do not enumerate correctly, check that all KVM switches
have the correct BANK address assigned to them and that all daisy-chain
cables are connected properly.
3.10 Verify that the Console has detected all secondary KVM switches by
scrolling through the BANKs using the On-Screen Display (OSD)
(refer to the “OSD-Menu Keyboard Commands” section on page 22).