BELL lighting 08900 User manual

Important Information
We recommend that luminaires are installed by
a qualified electrician ensuring the installation
complies with current IEE wiring regulations
BS7671:2018 & local building control.
• BELL will not accept responsibility for any claims
arising from a poor installation.
• The light source of this luminaire is not replaceable:
when the light source reaches end of life, the
whole luminaire must be replaced.
• Always switch o mains supply before installing.
Product Dimensions (mm)
Product Data
TUV Isolated Driver
Seoul Semiconductor LED
Read these instructions before installation and retain for future reference
This equipment should be installed by a competent electrician
Read these instructions before installation and retain for future reference
This equipment should be installed by a competent electrician
Technical Helpline [phone] British Electric Lamps Ltd, Unit A Foxbridge Way
Normanton Ind Est, Normanton, West Yorkshire. WF6 1TN
T: [phone] F: [phone] E: [email protected]
www.belllighting.co.uk
Installation Instructions: High Bay (08900/1/2/3/16/17)
Installation Instructions
Loop hanging installation
Physical Dimensions(mm/inch)
150W/200W
120W
100W
1. 2.
1.
2.
∅250x 173mm
(∅9.84" x 6.81")
∅250 x 191mm
(∅9.84 x 7.52")
∅280 x 203mm
(∅11.02 x 7.99")
Technical Parameters
Product Specifications
Input Voltage
Power Frequency
Outlook Dimensions
Luminaire Net Weight
Working Temperature
Storing Temperature
AC200-240V
50 / 60Hz
o o o o
-30 C to +50 C (-22 F to +113 F)
o o o o
-40 C to +70 C (-40 F to +158 F)
We appreciate your purchase!
Please read the instruction manual before installation and keep it for future reference.
Reminder
Application
Warning
With unique high-purity die-cast aluminum heat sink, high-brightness SMD chip, high-effciency constant
current and constant voltage power driver, the LED high bay is designed for factories, workshops,
warehouses, highwaytollstations,gasstations,supermarkets,exhibitionhalls, stadiums and similar
applications.
1. To avoid damage, falling, electric shock or fire, please do not modify the lamp or replace accessories without
confirming with the supplier first.
2. Please authorize only qualified personnel to install the lamp and ensure they follow the instruction manual.
Any improper installation might cause falling, electric shock, fire, or other injury, damage or hazard.
3. Please disconnect power before installation or any maintenance of the lamp.
4. Please disconnect power if it begins to smoke or emit odors, since fire or electric shock may occur. Ask
qualified person to inspect and maintain the luminaire.
5. Please do not dismantle the lamp without the supplier’s authorization.
6. Please do not touch the power supply when the lamp is operating.
7. The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire
shall be destroyed.
8. Terminal block not included. The electrical fitting must be installed by a licensed electrician.
9. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent
or a similar qualified person.
10. Only to be installed outside arms reach.
11. For use in environments where an accumulation of non-conductive dust on the luminaire may be expected.
12.Mounting heights of lights not higher than 30m.
Caution risk of electric shock
100W 120W 150W 200W
2.15±0.2kg
(4.74±0.44Lbs)
2.9±0.2kg
(6.39±0.44Lbs)
2.6±0.2kg
(5.73±0.44Lbs)
∅250(9.84")
52(2.05")
173(6.81")
∅25(0.98")
∅250(9.84")
52(2.05")
191(7.52")
∅30(1.18")
∅280(11.02")
64(2.52")
203(7.99")
∅30(1.18")
Installation Instructions
Loop hanging installation
Physical Dimensions(mm/inch)
150W/200W
120W
100W
1. 2.
1.
2.
∅250x 173mm
(∅9.84" x 6.81")
∅250 x 191mm
(∅9.84 x 7.52")
∅280 x 203mm
(∅11.02 x 7.99")
Technical Parameters
Product Specifications
Input Voltage
Power Frequency
Outlook Dimensions
Luminaire Net Weight
Working Temperature
Storing Temperature
AC200-240V
50 / 60Hz
o o o o
-30 C to +50 C (-22 F to +113 F)
o o o o
-40 C to +70 C (-40 F to +158 F)
We appreciate your purchase!
Please read the instruction manual before installation and keep it for future reference.
Reminder
Application
Warning
With unique high-purity die-cast aluminum heat sink, high-brightness SMD chip, high-effciency constant
current and constant voltage power driver, the LED high bay is designed for factories, workshops,
warehouses, highwaytollstations,gasstations,supermarkets,exhibitionhalls, stadiums and similar
applications.
1. To avoid damage, falling, electric shock or fire, please do not modify the lamp or replace accessories without
confirming with the supplier first.
2. Please authorize only qualified personnel to install the lamp and ensure they follow the instruction manual.
Any improper installation might cause falling, electric shock, fire, or other injury, damage or hazard.
3. Please disconnect power before installation or any maintenance of the lamp.
4. Please disconnect power if it begins to smoke or emit odors, since fire or electric shock may occur. Ask
qualified person to inspect and maintain the luminaire.
5. Please do not dismantle the lamp without the supplier’s authorization.
6. Please do not touch the power supply when the lamp is operating.
7. The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire
shall be destroyed.
8. Terminal block not included. The electrical fitting must be installed by a licensed electrician.
9. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent
or a similar qualified person.
10. Only to be installed outside arms reach.
11. For use in environments where an accumulation of non-conductive dust on the luminaire may be expected.
12.Mounting heights of lights not higher than 30m.
Caution risk of electric shock
100W 120W 150W 200W
2.15±0.2kg
(4.74±0.44Lbs)
2.9±0.2kg
(6.39±0.44Lbs)
2.6±0.2kg
(5.73±0.44Lbs)
∅250(9.84")
52(2.05")
173(6.81")
∅25(0.98")
∅250(9.84")
52(2.05")
191(7.52")
∅30(1.18")
∅280(11.02")
64(2.52")
203(7.99")
∅30(1.18")
Installation Instructions
Loop hanging installation
Physical Dimensions(mm/inch)
150W/200W
120W
100W
1. 2.
1.
2.
∅250x 173mm
(∅9.84" x 6.81")
∅250 x 191mm
(∅9.84 x 7.52")
∅280 x 203mm
(∅11.02 x 7.99")
Technical Parameters
Product Specifications
Input Voltage
Power Frequency
Outlook Dimensions
Luminaire Net Weight
Working Temperature
Storing Temperature
AC200-240V
50 / 60Hz
o o o o
-30 C to +50 C (-22 F to +113 F)
o o o o
-40 C to +70 C (-40 F to +158 F)
We appreciate your purchase!
Please read the instruction manual before installation and keep it for future reference.
Reminder
Application
Warning
With unique high-purity die-cast aluminum heat sink, high-brightness SMD chip, high-effciency constant
current and constant voltage power driver, the LED high bay is designed for factories, workshops,
warehouses, highwaytollstations,gasstations,supermarkets,exhibitionhalls, stadiums and similar
applications.
1. To avoid damage, falling, electric shock or fire, please do not modify the lamp or replace accessories without
confirming with the supplier first.
2. Please authorize only qualified personnel to install the lamp and ensure they follow the instruction manual.
Any improper installation might cause falling, electric shock, fire, or other injury, damage or hazard.
3. Please disconnect power before installation or any maintenance of the lamp.
4. Please disconnect power if it begins to smoke or emit odors, since fire or electric shock may occur. Ask
qualified person to inspect and maintain the luminaire.
5. Please do not dismantle the lamp without the supplier’s authorization.
6. Please do not touch the power supply when the lamp is operating.
7. The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire
shall be destroyed.
8. Terminal block not included. The electrical fitting must be installed by a licensed electrician.
9. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent
or a similar qualified person.
10. Only to be installed outside arms reach.
11. For use in environments where an accumulation of non-conductive dust on the luminaire may be expected.
12.Mounting heights of lights not higher than 30m.
Caution risk of electric shock
100W 120W 150W 200W
2.15±0.2kg
(4.74±0.44Lbs)
2.9±0.2kg
(6.39±0.44Lbs)
2.6±0.2kg
(5.73±0.44Lbs)
∅250(9.84")
52(2.05")
173(6.81")
∅25(0.98")
∅250(9.84")
52(2.05")
191(7.52")
∅30(1.18")
∅280(11.02")
64(2.52")
203(7.99")
∅30(1.18")
This product may contain substances that can be hazardous
to the environment if not disposed of properly. Electrical and
electronic equipment should never be disposed of with general
household waste but must be separated for its correct treatment
and recovery. Where possible recycle your packaging.
Warranty
Troubleshooting
?
Problem Possible Cause Solutions
LEDs stop working
LEDs flash on and off
The power line is improperly connected.
The power plug is loose.
The LED driver malfunctions.
The LED chip is damaged.
The output of the driver is abnormal.
The LED chip breaks down.
Reconnect the power cable.
Firmly plug the power in.
Replace with new driver.
Replace with new LEDs.
Replace with new driver.
Replace with new LED chip.
5 years warranty for original purchaser of LEDproduct that is identified on seller's invoice
reflecting its original purchase (the "Product").
1. In order to make a warranty claim, you must notify seller in writing within sixty(60) days after your
discovery of the defect, provide proof of purchase such as the invoice and comply with seller's other
warranty requirements. Upon receiving that notice, to ascertain why fixtures stop working, evidences
would be needed for seller's QC Team to analyze. Seller may require you to promptly return the Product
to Seller when necessary, freight prepaid.
2. The determination ofwhether the Product is defective shall be made by Seller in its sole discretion with
consideration given to the overallperformance of the Product.
3. If seller determines the Product is defective, Seller will elect, in its sole discretion, repair the Product
or replace the Product. Seller reserves the right to utilize new, reconditioned, refurbished, repaired or
remanufactured products or parts in the warranty repair or replacement process. Such products and
parts will be comparable in function and performance to an original product or part, as determined by
Seller in its sole discretion, and warranted for the remainder of the original warranty period. However,
cost of labor and equipment to remove the defective product and install a repaired or a replacement
Product at the end-user facility are excluded. Supplier's aggregate liability with respect to a defective
product shall in any event be limited to the money paid to buyer for that defective product.
The following circumstances will not be warranted:
1. Damage caused by force majeure such as war, riots, sabotage, cyclones, earthquakes, tidal waves,
flooding, lighting strikes, explosions, fire, flood, etc.
2. Damage caused by user's improper delivery, defects caused by wrong operation, wrong treatment
and destruction of machinery.
3. Dismantling or modification or improper maintenance or repairing of the products without the
supplier's authorization.
4. Damage caused by buyer or installer using bad quality cable or other mismatching electronic parts.
5. This warranty is invalid if the product is not used for the purpose for which is originally designed. Any
disputes occurred shall be applied to the laws and regulations of P.R.C.
The seller has the sole right to interpret and amend the above articles.
Instruction Manual
LED High Bay Light
100W/120W/150W/200W
Version: 01
Wiring Diagram
L
N
GND
brown
blue
yellow/green
Dimmable
DIM-
black
white
green
DIM+
gray
purple
Installation:
1. Rotate the suspension loop until it is fixed on the High Bay, fasten the security bolt. To secure, suspend the
fitting using the suspension loop.
2. Connect mains supply as diagram below.
∅250x 173mm
(∅9.84" x 6.81")
Technical Parameters
Product Specifications
Input Voltage
Power Frequency
Outlook Dimensions
Luminaire Net Weight
Working Temperature
Storing Temperature
AC200-240V
50 / 60Hz
o o o o
-30 C to +50 C (-22 F to +113 F)
o o o o
-40 C to +70 C (-40 F to +158 F)
100W
2.15±0.2kg
(4.74±0.44Lbs)
∅280 x 203mm
(∅11.02 x 7.99")
150W 200W
2.9±0.2kg
(6.39±0.44Lbs)

Installation Instructions: High Bay (08900/1/2/3/16/17)
Settings
By selecting the combination on the DIP switch,
sensor data can be precisely set for each application.
Detection Area
Detection area can be
reduced by selecting
the combination of the
DIP switches for each
application.
Stand By Dimming Level
The low light dimming
level you would like to
have after the hold time
in the absence of people.
Daylight Sensor
The sensor can be set
to only allow the fitting
to illuminate below a
defined ambient light
level.
When set to disable
mode, the daylight
sensor will switch on the
fitting when motion is
detected regardless of
ambient light level.
Note: the daylight sensor
is active only when the
lamp is switched o.
Hold Time
Refers to the time period
the lamp remains at 100%
illumination after no
motion is detected.
Stand By Period
Refers to the time the
fitting remains at a
low light level before
it completely switches
o. When set to disable
mode the low light
level is maintained until
motion is detected
On 1
I On 100%
II - 50%
On 2 3 4
I On On On 5 Sec
II - On On 30 Sec
III On - On 60 Sec
IV - - On 3 Min
V On On - 20 Min
VI - - - 30 Min
On 1 2 3
I On On On 0
II - On On 1 Min
III On - On 3 Min
IV - - On 10 Min
V On On - 30 Min
VI - - - ∞
On 6 7 8 9
I On On On On 5 Lux
II - On On On 15 Lux
III On - On On 30 Lux
IV - - On On 50 Lux
V On On - On 100 Lux
VI On On On - 150 Lux
VII - - - - Disable
On 4 5
I On On 10%
II On - 20%
III - On 30%
IV - - 50%
Technical Helpline [phone] British Electric Lamps Ltd, Unit A Foxbridge Way
Normanton Ind Est, Normanton, West Yorkshire. WF6 1TN
T: [phone] F: [phone] E: [email protected]
www.belllighting.co.uk