SloanLED 701946-6WMLP1 User manual

WARNING: Check Polarity – All connections must be RED-TO-RED (+)
and BLACK-TO-BLACK (-). Reverse polarity connections may damage
LEDs and will void product warranty.
3. Fasteners: If desired, modules can be
secured to sides of sign box using #6 (M3)
pan head sheet metal screws or 1/8"
(3 mm) aluminum rivets.
4. Connections: Modules may be connected
in series or parallel. Modules should not be
looped to create a closed circuit. Cap all
unused, exposed wire ends.
2. Peel and stick: Using provided double stick
tape, mount PosterBOX Mini modules to
sides of sign box.
Layouts: Mount PosterBOX Mini modules
on return of both long sides of sign box. If
brighter output is desired, mount on all four
(4) sides. It's recommended to test LED
density in a sample cabinet to evaluate
brightness, uniformity, and color. If you have
questions or require assistance in testing,
please contact your SloanLED Customer
Service Representative.
1. Clean surface: Clean inside of sign box with
rubbing alcohol and allow to dry. Clean all
mounting surfaces with alcohol for proper
tape adhesion.
NOTE: For optimum internal reection in single-
sided sign boxes, mount modules 0.2"-0.4"
(5-10 mm) from rear wall. For double-sided
sign boxes, mount modules in center of return.
WARNING: Risk of electrical shock. New installation and LED Retrot Kit installation
requires knowledge of sign electrical systems. If not qualied, do not attempt installation.
Contact a qualied electrician. Follow all NEC and local codes. PosterBOX Mini is not
suitable for submersion or direct exposure to water for extended periods of time.
For New Installation, proceed with Step
1 below. For Retrot Installations, begin
with Retrot Instructions on page 2.
Tools: Required – Measuring tape, wire
strippers, drill, and screwdriver.
Supplies: Required – Wire nuts and IDC
connectors or butt splices with appropriate safety
agency markings. Optional – PLTC cable, cable
ties, #6 (M3) pan head sheet metal screws or
1/8" (3 mm) aluminum rivets and silicone.
Components list:
• SloanLED PosterBOX Mini modules,
model numbers 701946-(X)WMLP1
• SloanLED 12 V Class 2 output power supply
(refer to "12 VDC Power Supply Capacity
Chart" for appropriate model numbers
• Optional: UL approved 18 AWG (1 mm²),
or larger diameter supply wire
• UL approved wire connectors appropriate
for wire gauge used
• Optional for mounting: Electrical grade
silicone, cable ties, #6 (M3) pan head sheet
metal screws, or 1/8" (3 mm) aluminum rivets
PosterBOX Mini
Installation Guide for 701946-6WMLP1
PAGE 1 OF 2

5. Connect to power supply: See Power
Supply Installation Guide for more
information regarding power supply
installation. CAUTION! Have a licensed
electrician connect primary power.
Retrot Instructions for Existing Signs
WARNING: Risk of re or electric shock. Install this kit only in host signs that have
been identied in the installation instructions, and where the input rating of the
retrot kit does not exceed the input rating of the sign. Installation of this LED retrot
kit may involve drilling or punching of holes into the structure of the sign. Check for
enclosed wiring and components to avoid damage to wiring and electrical parts.
GENERAL PURPOSE
RETROFIT SIGN CONVERSION.
FOR USE ONLY IN ACCORDANCE
WITH KIT INSTRUCTIONS.
KIT IS COMPLETE ONLY WHEN ALL PARTS
REQUIRED BY THE INSTRUCTIONS ARE PRESENT.
CAUTION: Turn o󰀨 power to sign before inspecting or removing existing light source. Power must remain o󰀨 while installing LED product.
ATTENTION : Coupez l'alimentation générale du panneau avant d'intervenir ou de retirer la source lumineuse existante. L'alimentation générale
doit être coupée tout au long de l'installation du kit de remplacement en LED.
1. Identify sign to be retrot and ensure branch circuit supplying existing sign are within voltage range for LED power supply.
Refer to components list (page 1) and "12 VDC Power Supply Capacity Chart" (page 3).
2. Remove existing lighting equipment intended to be replaced, such as neon or uorescent, and all power supplies, transformers, or ballasts.
Remove existing neon and all stando󰀨s to leave an empty sign cabinet. NOTE: All materials removed must be disposed of in accordance with
applicable local, state, and federal laws.
3. If required by local, state, or national electrical code, install a new disconnect switch.
4. Determine suitability and structural integrity of existing sign after removal of existing lighting equipment. If retrot does not require the making
of any new holes, do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. If existing holes
are present in a wet or outdoor location sign, repair and seal any unused openings in the electrical enclosure.
Openings greater than 0.5" (12.7 mm) diameter require a metal patch secured by screws or rivets and caulked with non-hardening caulk.
Smaller openings may be sealed with non-hardening caulk.
5. Clean inside of sign using non-oil based cleaner. Follow all manufacturer’s instructions and ensure inside of sign is dry before proceeding with
installation. This is an important step for good adhesion of PosterBOX Mini module mounting tape.
6. To populate sign, refer to PosterBOX Mini density guidelines as well as power supply loading chart (page 1) to determine appropriate number of
modules and power supplies. A list of acceptable power supply models is shown in the "12 VDC Power Supply Capacity Chart" (page 3).
7. Follow all instructions on page 1 under "New Installations" to properly install LED modules.
8. Connect modules to power supply output as shown on page 1 under "New Installations"
9. Connect power supply input as outlined in power supply installation guide in accordance with local, state and national electrical codes by
qualied personnel. Refer to power supply install guide included with power supply for details.
10. If required, install disconnect switch in accordance with local, state and national electrical codes by qualied personnel.
PosterBOX Mini
Installation Guide for 701946-6WMLP1
PAGE 2 OF 2

Customer service and technical support
888.747.4LED (888.747.4533)
SloanLED.com • [email protected]
Europe: Customer service and technical support
[phone]
SloanLED.com • [email protected]
P/N 402335 Rev B 2018-11-07
PosterBOX Mini is covered by CN200680037992.9, EP0890059, EP06812715.8, JP08-535482, NL1030161C2, US12089720 and patents pending.
12 VDC Power Supply Capacity Chart for PosterBOX Mini
Input Output
Power supply Part number Retrot certied Nominal input voltage Input current Power output Output current Maximum modules
Self-Contained 20 W 701680 100-240 V 0.55 A 20 W 1.5 A 15
Compact 12/25 W* 410174 100-277 V 0.40 A 25 W 1.9 A 19
60C1 60 W 701507-60C1 100-277 V 0.80 A
60 W 4.5 A 45
60W1 60 W 701507-60W1 100-240 V 0.85 A
60W2 60 W 701507-60W2 100-277 V 0.80 A
MODW(E) 60 W 701507-MODW(E) 100-240 V 1.00 A
MOD277 60 W 701507-MOD277 277-347 V 0.50 A
120D1 120 W 701507-120D1 100-277 V 1.70 A 2 × 60 W 2 × 4.5 A 45 × 2
Power used per module in watts: 1.2 W
* For sign applications, only certied for use outside of U.S. and Canada.
NOTE: Each 12 V circuit must be limited to 5 A (60 W) or less. For North American installations, a power supply that meets NEC Class 2 specications is required.
Extension of Power Supply Leads
If longer lead wire from power supply to LED modules is needed, an extension can be used. Extension should be kept as short as possible, i.e., under
15 ft for 18 AWG UL Listed PLTC (4.6 m for 1 mm² PLTC) or under 50 ft for 14 AWG UL Listed PLTC (15.2 m for 2.5 mm² PLTC).
Troubleshooting
NOTE: A licensed electrician should perform all applicable steps.
Entire box or leg does not light after
complete installation.
Check connection from power supply lead to rst module. Make sure polarity of connections made at the power supply lead—between modules
and any jumper wire—is correct. All connections must be RED-to-RED and BLACK-to-BLACK.
Still does not light. Check output voltage of power supply using a multimeter. The output voltage should be 12.0 VDC ± 0.5 VDC. If there is no output voltage, have a
licensed electrician check input voltage. Make sure power supply is connected correctly and getting primary power. If power supply is connected
properly and getting primary power and there is still no output voltage, try a different power supply.
Still does not light. If power supply is getting primary power and modules don't light, there may be a short in secondary wiring. Check all connections and cap all loose
wires.
The beginning of a leg lights, but entire leg
does not light or lights intermittently.
The primary cause of a portion of a PosterBOX Mini leg not lighting or lighting intermittently is a bad connection or reverse polarity connection
between modules that light and modules that don’t light. Check this connection.
One module does not light, but all others
in leg light.
PosterBOX Mini is designed so if one module fails, it will not cause the entire sign or leg to go out. If one module does not light, but all others in the
leg do, replace this module with a new one.
E215393
PosterBOX Mini
Installation Guide for 701946-6WMLP1
PAGE 3 OF 2