
Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
The power supply is Double Insulated and does not
require connection to an Earth circuit.
The LED units are Safety Extra Low Voltage and
must not be earthed.
Please read these instructions carefully before
commencing any work.
Thisunitmustbefittedbyacompetentandqualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
ThissystemoperatesatSafetyExtraLowVoltageviaa
transformer.Neverconnectthelightfittingsdirectlyto
the mains without using a transformer.
Ensurethatthesuppliedtransformerisused.
Themainsplugmustbesituatedindoors(e.g.house,
garage,shed)inordertoprotectitfromtheelements.
Donotexceedthetransformerload.Transformersmay
requireaminimumloadtooperate.
Always disconnect the transformer from the mains
when installing or maintaining this system.
Thissystemcontainsnon-replaceablepartsand
cannotbeserviced.Ifdamageoccursthepartshould
bescrapped.
Thisproductcannotbedimmed.
Wasteelectricalproductsandbatteriesshouldnot
bedisposedofwithhouseholdwaste.Pleaserecycle
where facilities exist. Check with your local authority
orretailerforrecyclingadvice.
Specification
TheKitshouldcontain:
•BSplugandin-linetransformerwith8.2mcable
• 4xLEDLightswith3mcable
• 4wayconnectorbox
Layout
• Planthedesiredlayoutofthesefittingscarefully,
ensuring the cables will reach the distances between
the transformer and each light fitting.
• Avoidlocatinganycablesinpositionsthatwould
causeatriphazard.Positioncablesawayfromareas
wheretheymaybeatriskfrombeingcut,trappedor
damaged.
• Ensuretheconnectorsareaccessibleforfuture
maintenance.
• Themainsplughasnospecialprotectionagainst
moisture and must be situated indoors.
• ThelightunitsareratedatIP44.Avoidpositioning
headunitsandconnectorsinverywetareas.
•All4headsmustbeconnectedtotheconnectorbox
toensureacompleteloopconnectionsothatthe
lights remain switched on.
• Only use this product in conjunction with the
In-line Transformer and Connector Box supplied.
Do not attempt to modify any component supplied.
• FirstlylayoutalltheLEDLightsunitsandcablein
theirdesiredlocationtoensuretheSupplyCable
from each unit will reach the Connector Box.
TheConnectorBoxmayneedtoberelocatedto
accommodatetheLightUnitpositions.DONOT
DRILLANYSURFACEUNTILYOUARECONFIDENT
ALLCABLEWILLCONNECT.
• TheDiagrambelowshowsthebasiclayoutofthe
kit,againensurecabledonotpresentahazard
whilst determining installation.
• Drilla30mmholeinthefixingsurface,passthe
supplycablethroughandinserttheDeckLightunit.
Bring the cable to the Connector Box and insert
firmly.Repeatthiswiththeremainingunits.
• TheConnectorBoxshouldbefirmlyfixedtoa
surfaceabovegroundlevel.
• ConnecttheConnectorBoxsupplycableintothe
in-lineTransformer,plugintothemainsandswitch
on to test.
Installation
3m
3m 3m 3m 3m
0.2m 5m
30mm diameter
mounting hole
35mm diameter LED
mounting board thickness
must be at least 12mm
• ThisKitcontainsLEDsthatarenon-replaceable
Bulb Replacement
Care and Cleaning
• Werecommendcleaningwithasoftdrycloth.
• Donotusesolventsorabrasivecleanersasthese
could damage the finish.
• Toprolongthelifeandkeepyouroutdoorlightingin
goodcondition,itisrecommendedthatperiodically
it is cleaned using a soft cloth followed by the
applicationofalightcoatingofoil,suchasWD40.
• Donotcleantheunitswithapressurewasher.