Larson Electronics PTB-1-75FT User manual

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 8
Remote Controlled Pan Tilt Base Rotates and Tilts with Mounting
Plate
75FT Input Cable
Instruction Manual
Thank you for your purchase of the Larson Electronics PTB-1-75FT.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE PTB-1-75FT MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING. RISK
OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOTINSTALLED PROPERLY. RISK
OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
The PTB-1-75FT industrial grade pan tilt base is designed to provide wireless and hard wired remote control of lights and
equipment. This remote control unit allows operators to rotate through from 0° to 355°, tilt from -60° to +30°, and mount
equipment weighing up to 100lbs.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor
areas where weatherproofing may be required. Universal voltage driver permits operation at 12V or 24V DC.

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 8
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Low Voltage DC
Connect power to power supply outputting low voltage between 9-42Volts DC.
This variable voltage allows greater versatility without affecting light output. Ensure
deutsch connectors are properly connected (If applicable)
DETACHABLE CORDS
•Cord is attached via a weatherproof 2-pin Deutsch connector.
•The cord is detachable by depressing the tab on the top of the connectors. This enables the
operator to remove and store the light while leaving the cord connected to the power source.
•Additional or replacement cords can be ordered from our website. Contact us or visit LarsonElectronics.com for more
information.
INSTALLATION NOTES
•Read this user’s manual thoroughly and retain it for future reference.
•Use a damp cloth to clean the unit.
•Never attach anything to this unit that could lead to danger.
•Do not install this unit to a surface that could become unstable such as a stand, tripod, shelf or table.
•Install the unit in an open area away from heat sources.
•Always use the voltage listed on the unit.
•Keep objects and cables away while the unit is in operation.
•Do not electrically overload this unit to prevent a risk of fire.
•Contact an electrician for installation if you are not familiar with electrical wiring.
How to Mount the Pan/Tilt Base
1. Determine the location you want tomount the base to.
2. Attach the pan/tilt base to your surface using the four corner thru-
holes at the base of the unit. Use the provided bolts to mount the base.
Be sure the unit will move freely and won’t contact the wall, ceiling
or pole during operation.
3. Bolt your device to the mounting plate on top of the unit and secure it tightly.
If necessary, usethe included 8x10” mounting plate.
Optional: Connect your device to one of the individual +/-leads on the base.
Seal off the additional wire if not used.

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 8
4. Attach and run the power cables. Take the 25’ cable
w/inline remote and securely attach the female connection
to the base.
5. Attach the hardwired remote to the other end of the cable
by screwing the female end of the remote assembly to the
male end of the wire harness.
6. If your unit will be hardwired, keep the flying leads
attached to the remote and hardwire the unit. Use the pin
tab to remove the flying leads and attach the cigarette
plug adapter if needed.
7. Find a location to mount the base for the hardwired
remote. Use the two screws provided.
8. Apply power to the unit to ensure proper function.

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
4of 8
Remote Control
•ON/OFF – Power’s the unit on or off.
•UP DOWNLEFTRIGHT - Moves the pan/tilt base in the corresponding
direction.
LOCK Remote Functionality
Press the LEFT +RIGHT buttons on the
hardwired remote simultaneously or press the
/button on the wireless remote.
A BLUE backlight on the hardwired remote
indicates the remote functionality is LOCKED. A
RED backlight indicates the remote functionality
is UNLOCKED and both the wired and
hardwired remotes will function.

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
5of 8
HANDHELD WIRELESS REMOTE PROGRAMMING PROCESS:
1. Switch off DC power.
2. Make sure there is NO other transmitter operating at the same time.
3. Switch on DC power, within 5 seconds press the remote's up and down button
once at the same time.
4. Searchlight will flash to acknowledge the remote, connection has been made.
5. To program the second remote (up to 4 remotes may be used with the
searchlight, programming a fifth will replace the first), within five seconds, pres
the second remote's up and down button after the first remote is acknowledged
or repeat step 1.

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
6of 8
Specifications
Materials Aluminum die-casting/Aluminum Plate
Color Black
Rotating angle Pan 0˚to 355˚±5˚, Tilt -60˚to +30˚±5˚
Rotating speed Pan 6.2˚/sec ± 0.6˚, Tilt 3.1˚/sec ± 0.6˚
Loading weight 66 lbs. at 70mm from Tilt table surface to center gravity
Power Consumption Pan: 6W, Tilt: 15W
Operating Temperature -25°C to + 50˚C
Weight 24 lbs.
Dimensions 12" L x 10" H x 8" W
Rating IP54

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
7of 8
Command Protocols
No Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7
1Command FFh Receiver ID 00h 04h DATA1 DATA2 CHECKSUM
Description
2Command FFh Receiver ID 00h 02h DATA1 DATA2 CHECKSUM
Description
3Command FFh Receiver ID 00h 08h DATA1 DATA2 CHECKSUM
Description
4Command FFh Receiver ID 00h 10h DATA1 DATA2 CHECKSUM
Description
5Command FFh Receiver ID 00h 20h 00h 00h CHECKSUM
Description
6Command FFh Receiver ID 00h 40h 00h 00h CHECKSUM
Description
7Command FFh Receiver ID 01h 00h 00h 00h CHECKSUM
Description
8Command FFh Receiver ID 00h 80h 00h 00h CHECKSUM
Description
9Command FFh Receiver ID 00h 00h 00h 00h CHECKSUM
Description
10 Command FFh Receiver ID 00h 03h 00h PRESET ID CHECKSUM
Description
11 Command FFh Receiver ID 00h 05h 00h PRESET ID CHECKSUM
Description
12 Command FFh Receiver ID 00h 07h 00h PRESET ID CHECKSUM
Description
13 Command FFh Receiver ID 00h 0Fh 00h 00h CHECKSUM
Description
14 Command FFh Receiver ID 00h 09h 00h 01~02h CHECKSUM
Description
15 Command FFh Receiver ID 00h 0Bh 00h 01~02h CHECKSUM
Description
Command
PAN LEFT
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
PAN RIGHT
TILT DOWN
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
DATA1:PAN SPEED(00~3Fh),DATA2:TILTSPEED(00~3Fh)
TILT UP
AUX OFF
AUX ON
ZOOM TELE
ZOOM WIDE
FOCUS NEAR
SETPRESET
PRESET ID=00~7Fh
FOCUS FAR
P/T/Z/F STOP
GOTO PRESET
PRESET ID=00~7Fh
CLEAR
PRESET PRESETID=00~7Fh
REMOTE
RESET

PTB-1-75FT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
8of 8
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is notnecessary toopen the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The PTB-1-75FT is designed to provide years of reliable performance. Should the need for replacement parts arise,
please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.