Belling platinum db2 Assembly Instructions

1
platinum db2 gas cooker
Installation & User’s instructions
platinum db2 - Natural Gas
Note: This appliance is supplied for use with the category of gas
specified and cannot be converted to any other gas.

2
Contents
Page
Product Specification ……………………………………………………. 3
Introduction Your Belling Cooker…………………………….. 4
Getting Help……………………………………… 4
Installation Instructions ……………………………………………………. 5-9
For Your Own Safety Never…………………………………………….. 10
Always…………………………………………… 11
Know Your Cooker ……………………………………………………. 12
Know Your Control Panel ……………………………………………………. 13
Timer Instructions …………………………………………………….. 14-18
Automatic Cooking (Large Oven) ……………………………………………………… 19
Rules to follow when cooking automatically
Using the Hob Description of Hotplates…………………………. 20
Use of Hotplates………………………………….. 20
Control Setting Guide…………………………….. 20
Cooking Chart…………………………………….. 20
Choosing Your Utensils …….. ………………….. 21
Energy Saving Tips….. ………………………….. 21
Safety Requirements for Deep Fat Frying….….. 22
Grilling (Closed Door) Caution…………………………………………….. 23
Using the Grill.…………………………………….. 23
The Ovens To Use the Ovens……………………………….. 24
Cold Start Cooking……………………………….. 24
Preparation & Roasting of Large Poultry……….. 24
Storage & Re-heating of Food Cook – Chill Dishes……………………………….. 25
Oven Cooking Chart ……………………..……………………………….. 26-27
Temperature Conversion Chart ……………………..……………………………….. 28
Care & Cleaning Control Panel / Oven Doors..……………………. 29
Ovens & Grill.……………………………………... 29-30
Pan Supports/Burner Caps/Burner Bodies…….. 30
Belling Cookclean Panels……………………….. 30
Replacing the oven lamp………………………… 31
Is There Something Wrong With Your Cooker ……………………..……………………………….. 32
Cooking Results Unsatisfactory ……………………..……………………………….. 33
Service ……………………..……………………………….. 34

3
Product Specification
Platinum db2
Gas Type I2H
Gas Supply Pressure 20mbar for G20
Electrical Supply 230V – 240V
Electrical Supply Frequency 50Hz
Total Heat Input (Gas) 16.1 kW
Total Heat Input (Electric) 2.6 kW
Large Gas Oven Wattage (Timed) 2.6 kW
Injector Bray 960/180
Small Gas Oven Wattage 2.4 kW
Injector 115
Grill Wattage (Electric) 2.39 kW - 2.6 kW
Front Left Hotplate (Rapide) 3.0 kW
Injector 115
Rear Left Hotplate (Semi-Rapide) 1.75 kW
Injector 96
Centre Hotplate (Wok - Triple Ring) 3.5 kW
Injector 135
Rear Right Hotplate (Auxiliary) 1.0 kW
Injector 71
Front Right Hotplate (Semi-Rapide) 1.75 kW
Injector 96
Grilling Area 780 cm2
Large Oven Capacity 55 Litres
Small Oven Capacity 32 Litres
Nominal External Dimensions H 900mm
(Excluding handles) W 1000mm
D 600mm
Countries of Destination GB & IE

4
Introduction
Your Belling Cooker Thank you for purchasing a new Belling db2 cooker. Its stylish, practical design
will enhance your kitchen and make cooking a pleasure. It features a large gas
oven, a small gas oven, a separate electric “closed-door” grill, a storage
compartment, 5 gas burners and a utensil holder. There is also an electronic
clock/timer featuring a minute minder and automatic cooking facilities (large oven
only).
Even if you have used an electric or gas cooker before, it is important that
you read these instructions thoroughly before starting to cook, paying particular
attention to the installation and safety instructions.
Getting Help If you have any problems with installing, operating, or cooking with your Belling
cooker, please check through these instructions thoroughly to make sure that
you have not missed anything. If you still need help, then please contact
(including a daytime telephone number if possible):-
Consumer Relations Department,
Belling Appliances Limited,
Talbot Road,
Mexborough, South Yorkshire,
S64 8AJ.
BELLING HELPLINE Tel: [phone]
Please quote the cooker model and serial number with all inquiries. This can be
found on the chassis behind the drop down storage compartment panel.
WARNING! For your own safety, make sure that these instructions on
installation, use and maintenance are followed.
We advise you to keep these instructions in a safe place for future reference.
If you sell or transfer ownership of this product, please pass on these instructions
to the new owner.

5
Installation Instructions
This appliance has been tested and certified by BG Technology and carries the
C.E. Mark.
The installation must be in accordance with the current I.E.E. Wiring Regulations.
Gas safety (Installation & Use Regulations.)
This appliance must be installed in accordance with BS6172.
In your own interest and that of safety, it is LAW that all Gas Appliances are
installed by competent persons in accordance with Gas Safety Regulations.
Failure to install appliances correctly could lead to PROSECUTION.
Use only a CORGI registered installer.
This appliance must be installed in accordance with the rules in force, and used
only in well-ventilated areas.
The use of a gas-cooking appliance results in the production of heat and moisture
in the room in which it is installed. Ensure that the kitchen is well ventilated, keep
natural ventilation holes open or install a mechanical ventilation device
(mechanical extractor hood).
Prolonged intensive use of the appliance may call for additional ventilation, for
example opening of a window, or more effective ventilation (where present).
Location The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not
in a room containing a bath or shower.
Provision for ventilation The room containing the cooker should have an air supply in accordance with
BS5440: Pt.2
All rooms require an opening window or equivalent, while some rooms require a
permanent vent in addition to the opening window. The cooker should not be
installed in a bed-sitting room of less than 21m3, and furthermore should not be
installed in any room of volume less than 5m3. If it is installed in a room of volume
between 5m3and 10m3an air vent of effective area 50cm2is required., unless the
room has a door that opens directly to the outside, in which case no air vent is
required. If the room exceeds 11m3no air vent is required
If there are other fuel burning appliances in the same room BS5440:Pt.2 should be
consulted to determine the requisite air vent requirements.

6
Installation Instructions
Unpacking After unpacking your cooker, make sure that you remove all the packing from the
grill compartment and ovens, and any stickers from the oven doors and the hob.
Examine your cooker for any damage. If there is any damage to your cooker or
anything is missing, please contact your supplier for advice.
Siting/Moving the Cooker Your cooker is heavy, so be careful when moving or positioning it. Do not try to
move the cooker by pulling on the doors or handles or control panel. The Belling
platinum db2 is designed to 'slot-in' between 600mm deep cabinets, spaced at
least 1000mm apart. It can also be used freestanding, with a cabinet to one side,
in a corner setting or with its back to a wall. However it must not be situated with
either side closer than 50mm to a combustible wall or cupboard that is higher than
the cooker. The wall behind the cooker and 450mm above and across the width of
the cooker, should be of an incombustible material or easy clean surface such as
ceramic tiles. Please note, when positioning your cooker against a wall, ensure
there is sufficient clearance for the screw heads on the back panel.
This appliance is designed not to project in front of standard 600mm worktops
(excluding handles). To achieve the best fit the cooker must be pushed against the
wall. If the wall mounted adaptor backplate (Fig.1) is to be fitted behind the
appliance then the suitable area for this fitting is shown as the area in (Fig.2).
Fig. 1 Fig. 2
ADAPTER BACKPLATE
ELBOW
ELBOW BAYONET
SOCKET
15mm COPPER
PIPE
MAINS INLET ON
APPLIANCE

7
Installation Instructions
Any overhanging surface or cooker hood should be at least 760mm (30") above
the cooker hob. We do not recommend positioning the cooker below wall
cupboards, as the heat and steam from the cooker may cause damage to the
cupboard and its contents.
Excess steam from the oven, vents out at the top back edge of the cooker, so
make sure that the walls behind and near the cooker are resistant to heat, steam
and condensation.
Your cooker must stand on a flat surface so that when it is in position the hob is
level. The cooker is fitted with rear wheels and will slide into position easily.
Movement of your cooker is most easily achieved by lifting the front, as follows.
Open the oven doors sufficiently to allow a comfortable grip on the underside front
edge of the oven roofs, avoiding grill elements or oven furniture.
Adjust the cooker at the rear to the required height, using the 2 jacking screws
situated behind the rear access cover and secure with the locknuts. Position the
cooker and adjust the height at the front with the 2 jacking screws situated at the
front underside. Check that the cooker is level by using a spirit level (adjusting the
jacking screws if necessary). It is important that the cooker is stable and level for
the overall cooking performance.
Stability Chain The cooker should be fitted with a stability device such as a proprietary stability
chain as shown in Figure 3 and firmly secured to the fabric of the building.
Whatever the position, remember to leave enough room for the cooker to be
pulled out for cleaning and service.
Connect to Gas Supply Connection to the appliance should be made with an approved appliance flexible
connection to BS669. A length of 1200mm is recommended.
The temperature at the rear of the appliance, which is likely to come into contact
with the flexible hose, does not exceed 70°C.
A Rp 1/2elbow is fitted to the cooker.
If the position of the wall connection is within 250mm of the oven inlet, the loop of
hose will give maximum movement to the cooker.
Fig.3

8
Installation Instructions
Connecting to Electrical For your own safety, we recommend that your cooker is installed by a suitably
Supply qualified person.
The cooker should be installed in accordance with the latest edition of the
IEE Regulations.
WARNING: THIS APPLIANCE MUST BE EARTHED!
The cooker must be connected to the correct electrical supply as stated on the
rating plate, through a suitable 20 amp fused spur outlet (13Amp fuse )
incorporating a double pole switch having a contact separation of at least 3mm in
all poles, adjacent to (but not above) the cooker.
We also recommend that a minimum 1.5mm²P.V.C. Insulated twin and earth
cable is used to connect the fuse spur outlet.
The power supply cable should conform to BS6004
IMPORTANT:
For access to the mains terminal block and for supply cable connection, it is
necessary to remove the access cover situated at the bottom of the back panel.
The live and neutral positions are marked with the letters L and N respectively,
molded into the terminal block. The earth terminal is marked by the earth
symbol.
Secure the mains cable using the cable clamp.
Connect the mains cable as follows:-
Live to terminal L.
Neutral to terminal N
Earth to the earth stud.
Ensure clamping nuts are tightened sufficiently. Allow sufficient cable length for
the cooker to be pulled out for cleaning, but do not let it hang closer than 50mm
(2”) to the floor. The cable can be looped if necessary, but make sure that it is
not kinked or trapped when the cooker is in position.
The large oven, grill and clock will not operate unless the mains control unit is live
and switched on.

9
Installation Instructions
Check for Gas Soundness
Gas pressure should be checked on a semi-rapid hob burner.
Remove the injector and fit the pressure test nipple supplied.
Light the other four burners and both ovens, then note the pressure.
This should be as stated on the rating label.
Note: Replace the injector after checking.
Retain the test nipple in a safe place for future use.
Check the operation of the cooker
Check that the five hotplate electrodes spark correctly. The hotplate burners
should be checked for a steady flame (when turned down to the smallest flame
setting marked on the control panel).
Check that the large oven sparks correctly by turning the control knob to mark 9.
The burner should ignite within five seconds at low rate and increase to full rate
within sixty seconds. Leave the oven full on with the door closed for ten minutes
and then check that the flame reduces when the control knob is turned to the ‘E’
setting.
Check that the small oven sparks correctly by turning the control knob to mark 9.
The burner should ignite within five seconds at low rate and increase to full rate
within sixty seconds. Leave the oven full on with the door closed for ten minutes
and then check that the flame reduces when the control knob is turned to the ‘E’
setting.
Before you cook for the first time, we recommend that you turn on each element
and hotplate in turn to burn off any odors remaining from manufacture. Simply
operate each hotplate and the grill on maximum for a few minutes and each oven
for about 30 minutes.
User
Instruct the user in the operation of the appliance and hand over the instructions.

10
For Your Own Safety
When used properly your Belling Cooker is completely safe, but as with any
cooker there are some precautions you must take in its use.
NEVER
•Never allow anyone except an authorized Belling Service Agent to service or repair
your cooker.
•Never remove any part of the cooker other than those intended in normal use, or
attempt to modify the cooker in any way.
•Never use the cooker for commercial catering. It is designed for domestic use.
•Never allow young children to operate or play with the cooker.
•Never use a chip pan or deep fat fryer more than 1/3full of oil, or use a lid while
frying and do not leave a fryer unattended while cooking.
•Never line the shelves, floor, or sides of the ovens or grill with aluminum foil as
overheating and damage may result.
•Never place anything which might catch fire, such as towels or tea towels, near to
the burners or over the flue outlet even when the cooker is not in use.
•Never use an asbestos mat, trivet or rack of any kind under pans on any hotplate.
•Never store anything which might catch fire in the oven, grill compartment or
storage compartment.
•Never allow aluminum foil or plastic to touch any hotplate when it is hot.
•Never store flammable liquids, aerosols, etc. in adjacent cabinetry.
•Never dry clothes or place other items over or near to the hotplate or oven or grill
doors.
•Never use large preserving pans or fish kettles across two hotplates as this will
damage the hob.
•Never use cooker as a room heater.
•Never wear garments with long flowing sleeves whilst cooking.
•Never leave burners lit when not in use.

11
For Your Own Safety
•Never use the hotplates with the burner caps removed.
•Never use badly designed or misshapen pans which may be unstable.
•Never allow pan handles to stick out beyond the hotplate (where they can be
knocked) or over another burner.
IF YOU SMELL GAS turn off all gas controls on the hob, open windows and turn
off gas supply at the mains. Do not operate any electrical switches and contact
your local gas supplier immediately.
ALWAYS
•Always make sure you understand the controls prior to use.
•Always take care when touching any part of the cooker that may be hot. Use good
quality dry oven gloves when removing or replacing food or dishes.
•Always stand back when opening the oven door to allow any build-up of heat or
steam to disperse.
•Always keep the oven and grill doors closed when not in use to prevent accidents.
•Always make sure that the roof, side and back panels, and shelves are fitted
correctly before using the oven or grill.
•Always keep your cooker clean, as a build-up of grease or fat from cooking may
be a fire hazard.
•Always switch off at the mains supply before cleaning your cooker.
•Always supervise children and pets, particularly when grilling, as exposed parts of
the grill may become hot.
•Always place pans centrally over the hotplate burners and make sure that they are
stable.
•Always keep handles away from the edge of the hob and any other burners. For
added safety you should consider using a suitable hob guard.
•Always make sure that all the controls are switched off when you finish cooking.
•Always remember that your cooker may stay hot for a time even after you have
finished cooking.
•Always keep ventilation slots at the rear of the cooker clear of obstructions.

12
Know Your Cooker
Plint

13
electricgrill
5
6
E
1
3
42
2
1
/
1
5
4
6
23
8
7
1
2
/
9E
closed
door
23
5
14
7
6
9
8
platinum db2
stop
Know Your Control Panel
Electric Grill Control Small Gas Oven control Spark Ignition Switch
(5) Gas Hotplate Controls
Large Gas Oven control Electronic Digital Clock, Minute Minder
(Programmable Timing Option) and Large Gas Oven Timer
Control Knobs & Switches The hob and ovens control knobs can only be rotated anti-clockwise from
the off position.
The grill control knob can only be rotated clockwise from the off position.
The spark ignition switch is operated as follows.
Depress and hold in the push-button. This will provide a repetitive spark to
the burners.

14
Timer Instructions
The oven timer offers you the following features:
1. Time of day
2. Automatic cooking (Large oven only)
3. Minute minder
The large oven can be controlled by the automatic timer. When the timer has been
set, the small oven remains functional.
Hints on Automatic 1. Select foods which will take the same amount of time to cook and require
Cooking approximately the same temperature.
2. Set the oven timer so that the food has just finished or about to finish cooking
on your return to the oven. This will ensure the food has not cooled down and
does not require re-heating before serving.
3. Food should be as cold as possible when it goes into the oven, ideally straight
from the refrigerator. Frozen meat and poultry should be thawed thoroughly
before being placed into the oven.
4. We advise that warm food should never be placed in the oven if there is to be
a delay period. Stews prepared by frying the meat and vegetables should be
cooked as soon as possible.
5. We advise dishes containing left over cooked poultry or meat (eg. Shepherds
pie) should not be cooked automatically if there is to be a delay period.
6. Stews and joints should be cooked by the long slow method, so that the delay
start is kept to a minimum.
7. On warm days, to prevent harmful bacterial growth in certain foods (eg.
Poultry, joints etc.) the delay start should be kept to a minimum.
8. Wine or beer may ferment and cream may curdle during the delay period, so it
is best that these ingredients are added just before serving.
9. Foods that discolour should be protected by coating in fat or tossing in water
(to which lemon juice has just been added) prior to placing the food into the
oven.
10. Dishes containing liquid should not be overfilled. This will prevent boiling over.
11. Foods should be well sealed (but not airtight) in a container to prevent the loss
of liquid during cooling. Aluminium foil gives a good seal.
12. Ensure food is cooked thoroughly before serving.

15
Timer Instructions
To set the Time of Day Step 1 Make sure all the oven controls are turned off.
Step 2 Check that the electricity supply to the oven is switched on.
Step 3 When switched on the display will show 0.00 and
Auto flashing intermittently.
Step 4 Press and hold the and buttons together (the
display shows 12.00). At the same time press either the “+” or
“-“ button to set the correct time of day.
RELEASE AND THE TIME OF DAY IS NOW SET.
To set Timer to switch (This allows you to cook immediately for a chosen period of time OFF
Automatically before the oven switches OFF Automatically)
Step 1 Ensure the time of day is set correctly.
Step 2 Place food onto the correct shelf position in the oven.
Step 3 Turn the oven control to the required temperature (The oven
Cookpot Symbol should now be operating).
Step 4
Press and release the button. The display will read 0.00 with the
cookpot lit.
Within 2 seconds press and hold the “ +” or “ -“ button until the
required cooking period is set.
(Adjustment can be made by pressing the “ -“ button)
The timer display will revert to the time of day with the Auto symbol
Cookpot Symbol Disappears and Cookpot lit.
At the end of the cooking period the Auto symbol will flash and an
intermittent bleeping sound will be heard. This will continue for
approximately 2 minutes unless the timer is reset within this period
(See step 6).
The oven will no longer operate until the timer has been reset to
manual operation (See steps 5 & 6 on the next page).

16
Timer Instructions
To set Timer to switch OFF Step 5 Turn off the oven control
Automatically (Continued)
Step 6 Press the button to cancel the bleeping (If 2 minutes has
not elapsed)
Press button again to return to manual operation.
To set Timer to switch ON (This allows you to cook at a specified time for a chosen period
& OFF Automatically before the oven switches OFF Automatically
Step 1 Ensure the time of day is set correctly.
Step 2 Place food onto the correct shelf position in the oven.
Step 3 Press and release the “ “ button. The display will read
0.00 with the cookpot lit. Within 2 seconds press and hold the
“+” button until the required cooking period is set.
(Adjustment can be made by pressing the “ -“ button).
The timer display will revert to the time of day with the Auto
symbol and cookpot lit.
Step 4 Press and release the “ “ button. The display will read
the earliest possible end time with the cookpot and Auto
symbol lit.
Within 2 seconds press and hold the “ +” to set the time you
require the food to be ready, with only the Auto symbol lit.
(Adjustment can be made by pressing the “ -“ button).
Step 5 Turn the oven control to the required temperature.
(The oven will now switch on later at the designated time, cook
for the required period and switch off automatically at the stop
setting).
At the end of the cooking period the Auto symbol will flash and an
intermittent bleeping sound will be heard. This will continue for
approximately 2 minutes unless the timer is reset within this period (See
Step 7).
The oven will no longer operate until the timer has been reset to
manual operation (See steps 6 & 7 on the next page).

17
Timer Instructions
To set Timer to switch ON & Step 6 Turn off the oven control
OFF Automatically (Continued)
Step 7 Press the button to cancel the bleeping
(If 2 minutes has not elapsed)
Press button again to return to manual operation.
Other Notes On Timer 1. When cooking Automatically the cook period can be checked at
Operation any time simply by pressing the “ “ button.
2. When cooking Automatically the stop time can be checked at any
time simply by pressing the “ “ button. (This also can be
altered at any time by following Step 4 previously).
3. Having set a cooking period and stop time an electronic device
stores the information. The device within the timer will switch the
oven on at the required start time.
4. If a mistake is made and is not easily rectified, alter the cook period
to show 0.00 (As per step 3 above) then press the “ “
button (See step 7 above).
5. After an automatic sequence the bleeping sound can be switched
off by pressing any of the following three buttons.
However, the large oven cannot be operated until the timer has
been set to manual. Press the Button (See Step 7 above).
6. If at any time the display shows three flashing zeros 0.00. It is
likely that the electricity supply to the oven has been interrupted.
Reset the timer to the correct time of day. If there is any food in the
oven, make sure that it has been cooked thoroughly before serving.
7. To give yourself more time to set each function press and hold the
required function button and at the same time press “ +“ or “ -“
button.
Note: Between the hours of 10.00 p.m. and 6.00 a.m. the intensity of the
display reduces.

18
Timer Instructions
To Set the Minute Minder Step 1 Ensure the time of day is set correctly
Step 2 Press and release the “ “ button. Within 5 seconds
press and hold the “ +” button until the required time is set
(A bell symbol will light).
This can be adjusted by pressing the “ -“ button.
On releasing the buttons the timer will revert back to the time of day.
At the end of the set time a bleeping sound will be heard and the bell
symbol will flash.
This can be cancelled by pressing the “ “.
Note: If necessary the Minute Minder can be cancelled before the tone
sounds by pressing the “ “ button and then press the “ -“ button
until 0.00 appears in the display window.
Bell symbol

19
Automatic Cooking (Large Oven)
Rules to follow when When planning your meal, remember that the oven control setting
cooking automatically refers to the center of the oven - it is warmer above and cooler below.
1. Food should be as cold as possible when it goes into the oven, ideally
straight from the refrigerator.
2. Frozen meat and poultry should be thawed thoroughly before it is put into
the oven.
3. The automatic timer should not be used in hot weather because of the
possible growth of food poisoning organisms.
4. NEVER use the automatic timer to re-heat Cook-Chill dishes.
5. Never leave food in the oven to cool slowly after cooking.
Serve immediately or refrigerate.
6. Dishes containing left over cooked meat or poultry, for example shepherds
pie, dishes containing eggs, cooked rice or seafood should not be cooked
automatically if there is to be a delay period.
7. Warm food should never be placed in the oven if there is to be a delay
period. Stews prepared by frying the meat and vegetables should be cooked
as soon as possible or refrigerated until loading the oven.
8. Try to set the stop time for a period beyond your anticipated return.
9. DO NOT leave food for an automatic program in a warm oven, i.e. one that
has just been used manually.
10. It is advisable to cover dishes where possible either with a lid or foil to
prevent the transfer of odours. If the food is to be served golden brown, it
may be uncovered or have the lid removed for a quick browning before
serving.
11. Dishes containing liquid should not be filled too full to prevent boiling over.
12. To prevent discoloration of certain fruit and vegetables such as apples,
pears, turnips and parsnips, a little lemon juice should be added to
the cooking liquid.
13. Potatoes should be par-boiled or brushed with fat to prevent discoloration
during delay time.
14. Wine or beer may ferment and cream may curdle during the delay period,
so it is best to add these ingredients just before serving.

20
Using The Hob
Description of The hob is made of enamelled mild steel and fitted with five gas
Hotplate Burners hotplate burners.
The left front hotplate burner (Raped) is rated at 3.0kW.
The left rear and right front hotplate burners (Semie – Raped) are rated at
1.75kW.
The centre hotplate burner (Wok – Triple Ring) is rated at 3.5Kw.
The right rear hotplate burner (Auxiliary) is rated at 1.0kW.
Use of Hotplates Check that the electricity supply is switched on. Select the burner to be used.
Push in and turn the control knob anti-clockwise to the large flame symbol .
Press the ignition button until the burner lights. Turn the control knob to the
required setting.
A simmer position is achieved when the control knob is turned fully anti-
clockwise.
To turn off, turn the control knob fully clockwise to the ‘0’ symbol.
Under certain conditions a slight ‘popping’ noise can be heard from the
hotplates. This is perfectly normal and will not affect the performance of the
appliance.
Control Setting Guide There are four sizes of hotplate burners on the hob and all are easily
Hotplates adjusted to any rate of cooking required.
The chart given below is provided as a guide only and personal experience will
soon familiarise you with the correct burner and setting to use. This depends
on the size, thickness, material of saucepans and the quantity and type of
ingredients being cooked.
COOKING CHART Burner Control Knob Uses Type of Food
position
Simmering Stews of fish, poultry and meet.
Milk puddings – steamed puddings.
Soups - boiled joints of meat e.g.
Ham, mutton, beef, scrambled egg.
SMALL FLAME Apple sauce.
Steady Boiling Vegetables.
Boiling jam after the sugar has been
added.
Shallow Frying Burgers, pancakes, omelettes, bacon
Eggs and raw fish.
LARGE FLAME Fast Boiling Bringing vegetables to the boil,
stir frying battered fruits fish and
pasta.