Bender RCMA426H User manual

Manual
RCMA426H
Residual current monitor
for monitoring AC, DC and pulsed DC currents
in earthed and resistance earthed systems
Software version D309 V1.0x
RCMA426_D00065_00_M_XXEN/05.2014

©Bender GmbH & Co. KG
All rights reserved.
Reprinting only with permission
of the publisher.
Subject to change!
Bender GmbH & Co. KG
P.O. Box 1161 • 35301 Gruenberg • Germany
Londorfer Str. 65 • 35305 Gruenberg • Germany
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Web: http://www.bender.de

Table of Contents
3
RCMA426_D00065_00_M_XXEN/05.2014
1. Effective use of this manual ........................................................................... 5
1.1 Notes for the user ............................................................................................. 5
1.2 Intended use ...................................................................................................... 5
2. Safety instructions ........................................................................................... 7
2.1 General safety instructions ........................................................................... 7
2.2 Work activities on electrical installations ................................................ 7
3. Function ............................................................................................................. 9
3.1 Device features ................................................................................................. 9
3.2 Function ............................................................................................................... 9
3.2.1 Transformer monitoring ............................................................................. 10
3.2.2 Quick query of the rated residual operating current ....................... 10
3.2.3 Self test, automatic ....................................................................................... 11
3.2.4 Self test, manual ............................................................................................ 11
3.2.5 Functional faults ............................................................................................ 11
3.2.6 Password protection (on, OFF) ................................................................. 11
3.2.7 Factory setting FAC ...................................................................................... 12
3.2.8 Erasable history memory HiS .................................................................... 12
4. Installation and connection ......................................................................... 13
4.1 Dimension diagrams .................................................................................... 13
4.2 Factory setting ............................................................................................... 15
4.3 Commissioning .............................................................................................. 15
5. Operation and configuration ....................................................................... 17
5.1 Getting to know the user interface ......................................................... 17
5.2 Understanding information on the standard display ...................... 18
5.3 Getting to know buttons and button functions ................................ 19
5.4 Starting a manual self test ......................................................................... 20

Table of Contents
4RCMA426_D00065_00_M_XXEN/05.2014
5.5 Erasing the fault memory ........................................................................... 20
5.6 Calling up and exiting the menu ............................................................. 20
5.7 Making settings in the menu .................................................................... 21
5.7.1 Selecting menus ............................................................................................ 21
5.7.2 Querying the software version with the InF menu ........................... 22
5.7.3 Making settings in the SEt menu ............................................................. 22
5.7.4 Querying and erasing the fault memory in the HIS menu ............. 24
6. Technical data ................................................................................................ 27
6.1 Data RCMA426H-D-2 in table form ......................................................... 27
6.2 Error codes ....................................................................................................... 30
6.3 Recommended contactors ........................................................................ 31
6.4 Response times of the RCMA426H system plus contactor in ac-
cordance with UL943 ................................................................................... 32
6.5 Ordering information ................................................................................... 33
6.6 Standards, approvals and certifications ................................................ 33
INDEX .................................................................................................................... 35

5
RCMA426_D00065_00_M_XXEN/05.2014
1. Effective use of this manual
1.1 Notes for the user
This manual is intended for experts in electrical engineering and
electronics!
In order to make it easier for you to find specific text passages or references in
this manual and for reasons of comprehensibility, important information is
emphasised by symbols. The meaning of these symbols is explained below:
1.2 Intended use
The AC/DC sensitive residual current monitor RCMA426H with its measuring
current transformer WN-35BS is used to monitor earthed and resistive-
earthed systems (TN and TT systems) in which DC and AC fault currents may
occur. These systems involve loads with six-pulse bridge rectifiers or half-
wave rectifiers with smoothing, e.g. converters and chargers.
In the event of a rated residual operating current IΔnof 6 mA, the device will
switch an alarm relay and the associated contactor in accordance with the op-
erating time specified in UL943.
The warning symbol indicates a potential dangerous
situation that may result in bodily injury and/or damage
to property.
Observe the associated safety instructions.
Information intended to assist the user to make optimum
use of the product are marked with the Info symbol.

Effective use of this manual
6RCMA426_D00065_00_M_XXEN/05.2014

7
RCMA426_D00065_00_M_XXEN/05.2014
2. Safety instructions
2.1 General safety instructions
In addition to these operating instructions, the "Important safety instructions
for Bender products“, which are also included in the scope of supply, are an in-
tegral part of the device documentation.
2.2 Work activities on electrical installations
 Only skilled persons are permitted to carry out the work necessary to
install, commission and run a device or system.
 Compliance with applicable regulations governing work on electrical
installations, and with the regulations derived from and associated
with them, is mandatory. EN 50110 is of particular importance in this
regard.
 If the device is being used in a location outside the Federal Republic of
Germany, the applicable local standards and regulations must be com-
plied with. European standard EN 50110 can be used as a guide.
Failure to carry out work on electrical installations prop-
erly and correctly can put life and limb at risk!

Safety instructions
8RCMA426_D00065_00_M_XXEN/05.2014

9
RCMA426_D00065_00_M_XXEN/05.2014
3. Function
3.1 Device features
 AC/DC sensitive residual current monitor with external 35 mm
measuring current transformer
 Can be used in conjunction with a contactor
 Rated residual operating current IΔn= 6 mA acc. to UL943
 Operating time acc. to UL943
 r.m.s. value measurement, frequency range 0…150 Hz
 Measured value display via multi-functional LC display
 Alarm signalling via LEDs (TPD, ERR) and K2 changeover contact
 Password protection to prevent unauthorised changes being made to
device settings
 Permanent fault memory
 N/C operation of alarm relay
 Device test when the power supply voltage Usis connected
 Automatic self test every 24 h
 CT connection monitoring
 Internal test circuit acc. to UL943 without additional external
components
 Internal test and reset button
 N-PE conductor monitoring on the load side
3.2 Function
The RCMA426H runs a device test when the power supply voltage is connect-
ed. During the start-up phase, the TRP LED lights up, the alarm LED ERR flashes
and the alarm relay switches to the alarm setting.
Once the device test has been completed successfully, the ERR alarm LED will
stop flashing, the TPD LED will go out and the alarm relay will return to the
normal setting.

Function
10 RCMA426_D00065_00_M_XXEN/05.2014
The device will check the circuit for the presence of residual currents even dur-
ing the self test.
An internal measuring current transformer is used for residual current meas-
urement. The actual measured value is indicated on the LC display. If the rated
residual operating current of 6 mA is exceeded, the alarm relay K2 will change
to the alarm state and the TRP alarm LED will light up.
Once the alarm relay has switched, the residual current must fall to less than
the rated residual operating current.
If it does not, error code E.04 will appear on the display and the ERR alarm LED
will flash. This means that the connected contactor has not shut down the
faulty circuit.
If the residual current falls below the release value, the error will continue to
be signalled due to the permanently activated fault memory. The alarm relay
K2 will not switch back to the initial state and the TRP alarm LED will not go
out until the reset button R is pressed or the power supply voltage is interrupt-
ed.
Parameters are assigned to the device via the LC display and the control but-
tons on the front panel; this function can be password-protected.
3.2.1 Transformer monitoring
The connections to the measuring current transformer are checked periodi-
cally every 10 s for short and open circuits. In the event of an error, the alarm
relay K2 will switch, the red TPD alarm LED will light up and the yellow ERR
alarm LED will flash (error codes E.01 or E.03). Once the error has been elimi-
nated, the alarm LEDs and the alarm relay will remain in the alarm state. Press-
ing the reset button R, the K2 will switch back to its initial state and the alarm
LEDs will go out.
3.2.2 Quick query of the rated residual operating current
When the display is in standard mode, the rated residual operating current IΔn
= 6 mA can be queried by pressing the Up or Down button
(< 1.5 s). Switching to menu mode is not necessary. Quick query mode can be
exited by pressing Enter (< 1.5 s).

Function
11
RCMA426_D00065_00_M_XXEN/05.2014
3.2.3 Self test, automatic
The device runs a self test every 24 h. Any internal malfunctions detected are
shown on the display as error codes. The automatic self test is carried out
without internal fault current. The alarm relay is not switched during the 24-h
test.
3.2.4 Self test, manual
The device runs a self test when the test button is pressed (> 1.5 s). Any inter-
nal malfunctions detected are shown on the display as error codes.
Whilst the test button T is pressed, all display elements available for this de-
vice are shown. When the button is released, the tES test symbol appears and
the manual self test commences.
During the manual self test, an internal test current of approx. 7 mA is evalu-
ated. Consequently, the TPD alarm LED lights up and the alarm relay switches.
Once the alarm relay has switched, the residual current must fall to less than
the rated residual operating current. If it does not, error code E.04 will appear
on the display to indicate that the connected contactor has not shut down the
load circuit.
If the self test has been successfully and the reset button R is pressed, the
alarm LEDs will go out and the relay will switch to its initial state.
If the self test has not been successfully, the TPD alarm LED will light, the ERR
alarm LED will flash, the alarm relay will switch to the alarm state and an error
code will be displayed.
3.2.5 Functional faults
In the event of an internal malfunction, the TPD alarm LED will light and the
ERR alarm LED will flash. An error code will appear on the display. Refer to
page 30 for details about error codes.
3.2.6 Password protection (on, OFF)
If password protection has been activated (on), settings can only be made
subject to the correct password being entered (0…999).

Function
12 RCMA426_D00065_00_M_XXEN/05.2014
3.2.7 Factory setting FAC
Activating the factory setting will reset all modified settings, with the excep-
tion of the device address, to the default upon delivery.
3.2.8 Erasable history memory HiS
The first alarm value to occur is written to this memory. The memory can be
erased via the menu HiS.

13
RCMA426_D00065_00_M_XXEN/05.2014
4. Installation and connection
4.1 Dimension diagrams
RCMA426H dimension diagram and drawing for screw fixing
The front plate cover is easy to open at the lower part marked by an arrow.
Dimensions in mm
Make sure that the installation area has been de-energised and
ensure compliance with the regulations for working on electri-
cal installations.
36 mm
90 mm
27,6
19,6
9,7
23 mm
18
1
2
3
Zubehör/
Accessory
100 mm
116 mm

Installation and connection
14 RCMA426_D00065_00_M_XXEN/05.2014
1. Mounting on a DIN rail:
Snap the mounting clip at the rear of the device onto the DIN rail so
that it sits securely.
Screw fixing:
Using a tool, position the rear mounting clips (a second mounting clip
is required, see the ordering information) so that it protrudes over the
enclosure. Fix the device in place with two M4 screws.
2. Wiring
The device must be wired as illustrated in the wiring diagram (exam-
ple).
Fig. 4.1: Wiring diagram
T1 T2
K1
K1
< U
3,15 A 3,15 A
T1 A2A1
T2
21 2422
T T/R R TT/R R
CT

Installation and connection
15
RCMA426_D00065_00_M_XXEN/05.2014
Key to wiring diagram
4.2 Factory setting
4.3 Commissioning
Checks must be carried out prior to commissioning to ensure that the residual
current monitor, and the associated contactors and peripherals have been
connected correctly.
Terminal Connections
A1, A2 Connection to the power supply
T1, T2 Test connections for internal monitoring circuit
T, T/R, R Connections for external test and reset button
21, 22, 24 Alarm relay K2: Connection to contactor or load switch
CT Internal measuring current transformer: D = 13 mm
K1 Recommended contactors are listed in the table on page 31
Rated residual operating
current, fixed value:
Hysteresis, fixed value:
Fault memory M:
Mode of operation K2:
Password:
6 mA
15 %
permanently activated
permanent
N/C operation (n.c.)
0, deactivated (Off)
Incorrect connections can lead to personal injury and
damage to equipment or property!

Installation and connection
16 RCMA426_D00065_00_M_XXEN/05.2014

17
RCMA426_D00065_00_M_XXEN/05.2014
5. Operation and configuration
5.1 Getting to know the user interface
1 Green Power ON LED:
Lights up when the power supply volt-
age is connected and the device is run-
ning.
2 Red TPD alarm LED:
Lights up when the rated residual op-
erating current IΔn is exceeded.
3 Yellow ERR alarm LED:
Flashes in the event of system errors.
An error code will appear on the dis-
play, e.g. E.03
4DISPLAY:
Displays operating information.
5 ENTER (< 1.5 s) / MENU (> 1.5 s) button:
Press this button to apply entries and
changes and call up the menu.
6 DOWN (< 1.5 s) / RESET (> 1.5 s) button:
Press this button to reduce input val-
ues and navigate through the menu, as
well as to perform a reset.
7 UP (< 1.5 s) / TEST (> 1.5 s) button:
Press this button to increase input val-
ues and navigate through the menu, as
well as to run a manual self test.
Fig. 5.1: User interface

Operation and configuration
18 RCMA426_D00065_00_M_XXEN/05.2014
5.2 Understanding information on the standard display
The actual measured residual current is displayed by default.
Press the Up or Down button to display the factory-set rated residual operat-
ing current IΔn. Pressing the Enter button restores the measured value.
In standard operation, the display can be toggled to the fixed
rated residual operating current I
Δ nof 6 mA using the Up/Down
button.
1
2
3
4
5
Fig. 5.1: Standard
1 Measured value display in mA:
2 Current type display AC / DC
3 Password protection activat-
ed
4 Fault memory activated

Operation and configuration
19
RCMA426_D00065_00_M_XXEN/05.2014
5.3 Getting to know buttons and button functions
The table below lists the functions of the buttons when navigating through
the display, navigating through the menu and when making settings. From
"chapter 5.7 Making settings in the menu" in the menu onwards, just the rele-
vant button symbol is used to indicate that buttons have been pressed.
Button Button symbol Function
Up/
Test
 Call up next display
 Go to the next menu/submenu/cat-
egory item
 Activate parameter
 Change (increase) parameter value
 Press and hold down button for
more than 1.5 seconds: run manual
self test
Down/
Reset
 Call up next display
 Go to next menu/submenu
 Deactivate parameter
 Change (reduce) parameter value
 Press and hold down button for
more than 1.5 seconds: erase fault
memory
ENTER/
Menu
 Call up menu/submenu
 Apply modified parameter value
 Press and hold down button for
more than 1.5 seconds: Call up
menu/exit menu/go to next highest
submenu
T
R
MENU

Operation and configuration
20 RCMA426_D00065_00_M_XXEN/05.2014
5.4 Starting a manual self test
You can start a self test manually. During the test, any internal malfunctions
detected are shown on the display as error codes. The alarm relay will be
switched.
To start a self test manually:
 Press and hold down the test button T (UP) or external test button
for more than 1.5 seconds.
5.5 Erasing the fault memory
The device has an erasable fault memory.
To erase the fault memory:
 Press and hold down the reset button R (DOWN) or external reset but-
ton for more than 1.5 seconds.
5.6 Calling up and exiting the menu
To call up the menu:
 Press and hold down the MENU (ENTER) button for more than 1.5 sec-
onds.
To exit the menu again:
 Press and hold down the MENU (ENTER) button again for more than 1.5
seconds.
The text “tES“ appears on the display along with all
available display elements.
The areas of the display which can be configured flash! This is
indicated by an oval marker in the illustrations below. Press and
hold down the MENU button > 1.5 s to enter menu mode.