BenQ DC C50 User manual

English
DC C50
User’s Manual
Welcome

English
Copyright
Copyright (c) 2003 by BenQ Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system or translated
into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without prior written per-
mission from BenQ Corporation.
Brands and product names are trademarks or registered trademarks of their respective
companies.
Disclaimer
BenQ makes no warranty of any kind with regard to this material, including, but not lim-
ited to, the implied warranties of merchantability and fitness for a particular purpose.
BenQ assumes no responsibility for any error that may appear in this document. BenQ
makes no commitment to update nor to keep current the information contained in this
document.
Taking care of your camera
• Do not use your camera over the following environmental range: temperature: O°C to
40°C, relative humidity: 45% ~ 85%.
• Do not use or store your camera in environments listed below:
Direct sunlight.
High humidity and dusty places.
Next to the air conditioner, electric heater or the other heat sources.
In a closed car that is directly under the sun.
Avoid shaky places.
• If your camera becomes wet, wipe it with dry cloth as soon as possible.
• Salt of seawater may cause severe camera damage.
• Do not use organic solvents, such as alcohol, etc., to clean your camera.
• If the lens or viewfinder is dirty, please use the lens brush or soft cloth to clean the lens.
Do not touch the lens with your fingers.
• To prevent electrical shock, do not attempt to disassemble or repair your camera by
yourself.
• Water may cause a fire or electric shock. Therefore, please store your camera in a dry
place.
• Do not use your camera outdoors when it is raining or snowing.
• Do not use your camera in the water.
• If the foreign substance or water gets in your camera, please tum the power off immedi-
ately and disconnect the batteries and the transformer. Remove the foreign substance or
water, and send it to the maintenance center.
• Transfer the data to the computer as soon as possible to avoid losing your image data.

BenQ DC 5330 Table of Contents
Table of Contents
Table of Contents
I
English
1. Touring your DC C50 ...................................1
1.1. Checking package contents ................................. 1
1.2. Parts of the DC C50 and their names .................1
1.2.1. Front View ..................................................................... 1
1.2.2. Rear View ....................................................................... 2
1.2.3. Mode Dial ...................................................................... 3
1.2.4. Viewfinder LED Indicator ............................................ 3
2. Preparing your DC C50 for using .................4
2.1. Loading the battery ............................................. 4
2.2. Using an AC Power Adapter: ............................. 4
2.3. How to charge the Battery: ................................ 5
2.4. Loadig an SD Memory Card: ............................. 5
2.5. Attaching the Strap: ............................................ 6
3. Using the DC C50 ..........................................7
Working Mode ........................................................... 7
3.1. Auto Capture Mode ............................................. 7
3.1.1. Compose the pictures .................................................... 7
3.1.2. Using the Optical Zoom ................................................ 9
3.1.3. Using the Digital Zoom ................................................. 9
3.1.4. Using the Self-timer ...................................................... 10
3.1.5. Using the Flash .............................................................. 11
3.1.6. Changing the Focus ....................................................... 12
3.1.7. Changing the Exposure Compensation ....................... 13
3.1.8. Capture Mode Setup ..................................................... 14
3.1.8.1. Picture Setting .....................................................................15
3.1.8.2. Function Setting ..................................................................17
3.1.8.3. AE/AWB Setting ..................................................................19
3.2. Program Mode .................................................... 21
3.3. Shutter Speed-priority Mode .............................. 21

BenQ DC 5330 Table of Contents
Table of Contents
Table of Contents II
English
3.4. Aperture-priority Mode ...................................... 22
3.5. Full Manual Mode ...............................................22
3.6. Portrait Mode ......................................................23
3.7. Sports Mode ........................................................23
3.8. Night Scene Mode ..............................................23
3.9. Video Mode .........................................................24
3.10.!Playing Back Images.......................................... 25
3.10.1. Playing Back Photographed Images ........................... 25
3.10.2. Voice Record ................................................................ 26
3.10.3. Playing Back Movies .................................................... 26
3.10.4. Thumbnail Display ...................................................... 27
3.10.5. Zoom Playback ............................................................ 27
3.10.6. Slideshow Display ........................................................ 28
3.10.7. Playback Mode Setup .................................................. 28
3.10.7.1. DPOF (Digital Print Order Format) ................................28
3.10.7.2. Protect ................................................................................29
3.10.7.3. LCD Brightness ..................................................................30
3.10.8. Erasing Images.............................................................. 30
3.11.!SET-UP MODE ................................................32
3.11.1. Basic Setting ................................................................ 32
3.11.2. Custom Setting ........................................................... 34
4. PC dependent features ..................................36
4.1. Installing digital camera software ....................... 36
4.2. The Software of this Installation CD ..................37
4.3. Downloading the Image(s) .................................38
5. Troubleshooting (Error Message Table) ......39
6. Specifications .................................................41
7. Service information .......................................42

BenQ DC 5530 User’s Manual
Touring your DC C50
1
English
TOURING YOUR DC C50
1.1. Checking package contents
The package should include the following items:
1.2. Parts of the DC C50 and their names
1.2.1. Front View
•DC C50 digital camera
•Lithium-ion Battery (rechargable)
•SD Memory Card
•AC power adapter
•Camera pouch
•Hand Strap
•BW cable
•USB cable
•User's manual
•DC C50 software CD-ROM
1.!Self-timer/AF support LED
2.!Optical viewfinder
3.!Built-in flash
4.!Shutter button
5.!Lens/lens cover
6.!POWER.Power button
7.!MIC.Microphone
8.!Mode dial
9.!DC IN 5V terminal
10.!USB/A/V OUT terminal

BenQ DC 5530 User’s Manual
Touring your DC C50 2
English
1.2.2. Rear View
1.!Diopter adjustment dial
2.!Viewfinder
3.!Viewfinder LED
4.!/ Zoom button
5.!Speaker
6. .Menu button
7. .Display button
8.!Strap attachment
9.!Command dial
10.!.Delete button
11.!Tripod socket
12.!Battery/ SD Memory Card cover
13. !LCD monitor
Rear Buttont:
1.!.Arrow button (up)
!.Focus button/macro
2.!.Arrow button (left)
!! .Exp./back light
3.!SET.Set button
4.!.Arrow button (right)
!! .Flash button
5.!.Arrow button (down)
!! .Self-timer button/interval

BenQ DC 5530 User’s Manual
Touring your DC C50
3
English
1.2.3. Mode Dial
1.2.4. Viewfinder LED Indicator
Color State Description
Photography Mode Setup Mode
Charge Mode
PC Mode Battery
Green On AE or AF is locked with the
Shutter button held half
down.
In standby mode. In communication to
PC. (SD Memory Card
is inserted.)
Under charging
Red On Writinr to SD Memory Card
in progress.
Accessing of
SD Memory
Card in progress.
In connecting to PC.
(SD Memory Card is
inserted.)
Error
Flashing When the image is not in
focus.
------ ------ Interval timer
standing by
Orange On Processing images
Charging of flash
in progress
------ Disconnection (SD
Memory Card is
inserted.)
No battery
Flashing Hardware malfunction SD Memory Card is
not inserted.
------
Mode Dial
1.!;!Auto mode
2.!P;!Program mode
3.!TV ;!TV (Shutter Speed priority)
4.!AV;!AV (Aperture priority)
5.!M;!Manual mode
6.!;!Portrait mode
7.!;!Sports mode
8.!;!Night scene mode
9.!;!Movie mode
10.! ;!Tfu.vq!mode
11.!PC;!PC mode
12.!;!Playback mode

BenQ DC 5530 User’s Manual
Preparing your DC C50 for using 4
English
PREPARING YOUR DC C50 FOR USING
2.1. Loading the battery
2.2. Using an AC Power Adapter:
Note
•!Use only the specified battery type (Lithium Ion).
•!If you are not going to use the battery for an extended period of time, remove it from
the camera to prevent leakage or corrosion.
•!Avoid using battery in extremely cold environments as low temperatures can shorten
the battery life and reduce the camera performance.
You can use a Lithium Ion battery to power on the camera. Battery power is convenient for
capturing images or video clips.
1.!Make sure the camera power is off.
2.!Open the battery/SD Memory Card cover.
3.!Insert the battery in the correct orientation shown.
•Tilt the battery lock lever toward the strap
attachment and then insert the battery following
the orientation of the arrow on the batteryís label.
•Insert the battery as far as it can go.
4.!Close the battery/SD Memory Card cover.
•To remove the battery:
Open the battery/SD Memory Card cover and
then release the battery lock lever. After the battery
is slightly ejected, pull out the battery slowly.
Battery lock lever
1.!Make sure the camera power is off.
2.!Connect one end of the AC power adapter to the
DC IN 5V terminal.
3.!Connect the other end of the AC power adapter to a
power outlet.
Note
•Make sure to use only the AC power adapter specified for the camera. Damage caused
by the use of an incorrect adapter is not covered under the warranty.
•!Using an AC power adapter while transferring images to your computer in order to
prevent unexpected automatic power off of the camera.

BenQ DC 5530 User’s Manual
Preparing your DC C50 for using
5
English
2.3. How to charge the Battery:
2.4. Loadig an SD Memory Card:
All images and video clips taken by the camera can be stored in an SD (Secure Digital)
Memory Card.!Even if the cameraís power is OFF, the images saved in the SD Memory Card
are not erased. An SD Memory Card can be repeated read and written.
1.!Make sure the camera power is off.
2.!Slide the battery/SD Memory Card cover into the direction of the [OPEN] arrow.
3.!Insert the battery, noting correct polarity (+ and -).
4.!Slide the battery lock lever to adjust the battery.
5.!Close the battery/SD Memory Card cover firmly.
6.!Connect one end of the AC power adapter to the DC IN 5V terminal.
7.!Connect the other end of the AC power adapter to a power outlet.
Charging start: Green indicator
Charging end: Indicator off
Stand by: Orange indicator
Replace a new battery: Red indicator
Note
•Make sure to use only the AC power adapter specified for the camera. Damage caused
by the use of an incorrect adapter is not covered under the warranty.
•When the charging is not started even if proceeding the operation above. Press power
button on at any mode after LCD indication appears, then turn the power off.
•Do not place the camera in hot temperature. Use it at room temperature.
1.!Make sure the camera is off.
2.!Slide the battery/SD Memory Card cover in the
direction of the [OPEN] arrow.
3.!Insert an SD Memory Card :
•The front side of the memory card(printed arrow)
should face towards the front side of the camera.
•If the card cannot be inserted, check the orientation.
4.!Close the battery/SD Memory Card cover.
•To remove the SD Memory Card, make sure!the
camera is off. Open the battery/SD Memory Card card cover.
Press lightly on the edge of the memory card and it will eject.

BenQ DC 5530 User’s Manual
Preparing your DC C50 for using 6
English
2.5. Attaching the Strap:
Note
•If the camera is powered-on without the card, the
#NO CARD#message appears on the LCD monitor.
•To prevent valuable data from being accidentally
erased from an SD Memory Card you can slide the
write-protected tab (on the side of the SD Memory
Card) to!#LOCK#.
•To save, edit or erase data on an SD Memory Card,
you must unlock the card.
•MMC Card can not be accepted to use.
•Please format an SD Memory Card by this camera before use.
To prevent accidental slippage during the use, always use the strap.
Attach the hand strap as follows:
1.!Thread the small loop of the hand strap through
the strap eyelet on the camera.
2.!Pull the large loop through the small loop until the
strap is firmly secured.
Write-protect tab Write-prote ction state

BenQ DC 5530 User’s Manual
Using the DC C50
7
English
USING THE DC C50
This section describes the ten modes included in this camera. An in-depth coverage of these
modes will be further described. Here are the ten main functions of this camera:
Working Mode
3.1. Auto Capture Mode![ ]
3.1.1. Compose the pictures
Your camera provides a single image capturing, continuous image capturing and auto
exposure bracketing capturing. It is equipped with both an optical viewfinder and a 1.5" full
color TFT LCD monitor to compose images. Taking images by using the optical viewfinder
will conserve more battery power. The LCD monitor can help you accurately compose the
pictures and examine all details. However, this may also consume you more battery power.
1.!Turn the camera on by pressing the POWER button.
2.!Set the mode dial to [ ].
3.!Compose your shot in the viewfinder.
•Turn the ìdiopter adjustment dialî until the image
appears clearly within the viewfinder.
4.!Press the shutter button down halfway, then press it
down fully.
•The viewfinder LED indicator lights red while the
camera!is processing a captured image.
Note
•Voice memo is starting to record at still image!capture
mode just after the photograph is taken in case of
activating this function. It provides 10seconds for
recording and only can be done once . To terminate
recording,press the shutter button down fully.
Diopter adjustment dial

BenQ DC 5530 User’s Manual
Using the DC C50 8
English
!Using the LCD monitor
LCD Monitor Display (Capture Mode)
The [ ] Display button can select display format. Whether in!#Still Image#or!
#Movie#mode, preview image with full OSD is displayed.
OSD (on-screen-display) full display OSD display OFF LCD monitor OFF
Note
•The image in the LCD monitor darkens in strong sunlight or bright light. This is not a
malfunction.
•Using the LCD monitor for an extended period of time will decrease the number of images
you can take. To increase the shots and conserve battery power, it is recommended to turn
the LCD monitor off and use the viewfinder instead.
2.!Compose the picture in the LCD monitor.
3.!Press the shutter button down halfway (the camera adjusts the exposure and the
focus), then press it down fully.
•The viewfinder LED indicator lights red while the camera is processing a captured
image.
Mode dial setting
Macro
Focus area
Backlight
conpensation
Slow shutter speed
Battery condition
Flash light status
Picture size
Picture quality
Self-timer
Possible number
of shots
Zoom state Voice icon

BenQ DC 5530 User’s Manual
Using the DC C50
9
English
3.1.2. Using the Optical Zoom
The lens moves during the zoom photography. Zoom photography allows you to take
telephoto and wide-angle shots. The subject appears closer by pressing the [ ]button and
appears farther away by pressing the [ ] button.
3.1.3. Using the Digital Zoom
By using the digital zoom, images can be enlarged so that the subject appears closer. However,
the more the image is enlarged, the grainer the image will become. The digital zoom function
is only available when you set the LCD monitor and the digital zoom to ON. To capture a
digitally zoomed image, perform the following steps:
1.!Set the mode dial to one of [ ], [ P], [ TV ],
[AV ], [ M], [ ], [ ], [ ] , [ ] and
power on the camera.
2.!If required,turn on the LCD monitor by pressing
the [ ]button.
3.!Compose the picture by using the [ ]/[ ]!
button.
•Pressing the [ ]button zooms in on the
subject, and enlarges the subject on the LCD
monitor.
•Pressing the [ ]button provides a wider angle
picture.The lens position moves according to the
zoom button setting.
4.!Press the shutter button down halfway, then press
it down fully.
1.!Set the mode dial to one of [ ], [ P], [ TV ], [ AV ],
[M], [ ], [ ], [ ] , [ ] and power on the camera.
2.!If required,turn on the LCD monitor by pressing the
[]button.
3.!To enable the digital zoom is as follows:
a.!Press the MENU button.
b.!Press the or !button to select F
F
unction page.
c.!Press the or !button to select D
D
igital Zoom, and
press the SET button.
d.!Press the or button again to select O
O
N, and press
the SET button.
e.!Press the MENU button.
f.!To activate the digital zoom, press the [ ] button
completely and hold it until the image on the L
L
CD monitor
expands.
4.Press the shutter button to capture a “zoomed” image.
Optical Zoom
Digital Zoom
Optical Zoom
Digital Zoom

BenQ DC 5530 User’s Manual
Using the DC C50 10
English
3.1.4. Using the Self-timer
The [ ] self-timer button can select the capturing mode between!#OFF#(default) and
#Self timer (2 sec., 10 sec., 10+2 sec. or Interval)#.
[2 sec.] The camera automatically takes a picture after two seconds delay.
[10 sec.] The camera automatically takes a picture after ten seconds delay.
[10+2 sec.] The camera automatically takes a picture after ten seconds delay, and
takes again after two seconds.
In case of flash light capacitor is not charged up, the second take can be
done at two second after charged.
[Interval] The camera automatically takes a picture every preset time till media
full or battery empty.
To activate the self-timer by pressing the shutter button. After selecting this mode, self-timer
icon displays on L
L
CD monitor and then LED on the front panel blinks fast for the last 3
seconds. Using the self-timer allows you to get into the scene when taking group images.
Note
•The camera has 1X to 3X optical zoom and 1X to 4.0X electrical zoom function.
•Digital zoom function is terminated when user selects LCD off mode.
1.!Secure the camera to a tripod or place it on a stable surface.
3.!Set the mode dial to one of [ ], [ P], [ TV ], [ AV ],
[M], [ ], [ ], [ ] , [ ] and power on the camera.
3.!Press the [ ] button.
•When you toggle the self-timer button, the following are
displayed in the accordingly order:
Off 10 sec 2 sec 10+2 sec Interval
4.!Compose the picture.
5.!Press the shutter button down halfway, then press it down fully.
•The self-timer function is activated.The photograph is then taken after the preset time.
•When the photographs are taken using the LCD monitor, the count down is displayed.
Note
•After an image is taken using self-timer, the self-timer mode is turned off.
•The self-timer is not possible in the continuous capture mode.
•The self-timer is only available for 2 or 10 seconds delay at [ ] mode. The camera
automatically starts to recording after 2 or 10 seconds.

BenQ DC 5530 User’s Manual
Using the DC C50
11
English
3.1.5. Using the Flash
The flash is designed to function automatically when lighting conditions warrant the use of
flash. You can take an image using a suitable flash mode to your circumstances. If you change
the flash mode, the camera will retain that setting even if the camera is turned off.
The camera has FOUR flash modes: Auto, Red-Eye Reduction, Forced Flash and Flash Off.
The table below will help you to choose the appropriate flash mode:
Icon Flash Mode Description
[ ] Auto Flash The flash fires automatically according to the ambient lighting conditions.
[ ] Red-Eye
Reduction (With
auto-flash except
to [TV][AV],[M])
Select this mode for general photography. The flash emits a precursor-flash
before except the main flash fires. This causes the pupil in the human eyes to
contract, reducing the red-eye phenomenon. Select this mode when taking
images of people and animals in low-light conditions.
[ ] Forced Flash The flash will always fire regardless of the surrounding brightness. Select
this mode for recording images with high contrast (back lighting) and deep
shadows.
[ ] Flash Off The flash will not fire.
Select this mode when taking images in a place where flash photography is
prohibited, or when the distance to the subject is beyond the effective range
of the flash.
Note
•Auto flash can only be set at [ ] mode. It can not be set at [M], [P], [TV] and [AV] modes.
•In the [ ] Portrait mode, flash setting is fixed to Red-Eye Reduction mode automatically.
•In the [ ] Sports mode, flash setting is fixed to [ ].
•In the [ ] Night scene mode, flash setting is fixed to [ ] except [ ] Focus mode
2.!Set the mode dial to one of [ ], [ P], [ TV ], [ AV ],
[M]!and power on the camera.
3.!Press the [ ] buttonrepeatedly until your desired flash
mode appears.
•When you toggle the flash button at [ ] mode, the
available flash modes are displayed in the following order:
3.!Compose the picture and press the shutter button down halfway, then press it down fully.
Note
•After flash fires, it takes approximately 5 seconds to 10 seconds to be ready for the
next shot during solid orange indicator.
!!!!!!!!!![No display]!Auto \^!Red-Eye/Forced Flash
!!!!!!!!!!!
!!!!!!!!! \^!Suppressed Flash \^!Forced Flash

BenQ DC 5530 User’s Manual
Using the DC C50 12
English
3.1.6. Changing the Focus
1. Set the mode dial to one of [ ], [ P], [ TV ], [ AV ],
[M], [ ], [ ], [ ] , [ ] and power on the camera.
2. Toggle the [ ] Focus button.
The selected focus mode is displayed on the LCD monitor.
[no indication]: Normal Auto Focus (0.8m to infinity).
[ ]: Macro Auto Focus (0.09m to infinity/Wide,
0.3m to infinity/Tele).
[ ]: The camera will focus on the subjects in a
distance of infinity to take photos.
[3m]: The camera will focus on subjects in a
distance of 3m to take photos.
[1m]: The camera will focus on subjects in a
distance of 1m to take photos.
3. Compose the picture.
4. Press the shutter down halfway,then press it down fully.
Note
•When shooting a close-up in Macro mode, use the LCD monitor to compose your shot,
avoiding the off-center parallax phenomenon.
•There is not a distinct point (subject range) at which Normal mode is favored over
Macro mode; take in image in both optical modes and compare the results.
•After a Macro shot is taken DO NOT FORGET to reset the lens to the normal position.

BenQ DC 5530 User’s Manual
Using the DC C50
13
English
3.1.7. Changing the Exposure Compensation
This setting [ ] allows you to intentionally lighten or darken the entire image. Use this
setting when the optimum brightness (exposure) cannot be obtained, for example, when the
brightness between the subject and the background is not balanced or when the subject to
photograph occupies only an extremely small part of the screen.
The [ ] Exposure Compensation button can select “Normal capturing mode”,
“Backlight compensation capturing mode” and “Exposure compensation adjusting mode”
cycling.
1. Set the mode dial to one of [P], [TV], [AV] and power on the camera.
2. Toggle the [ ] button to select exposure compensation mode or backlight
compensation mode.
3. When exposure compensation mode is seleced, rotate the Command dial to adjust the
exposure, and press the [ ] button again to confirm.
•Rotate the Command dial to counter clockwise direction to decrease (darken) exposure,
and rotate the Command dial to clockwise direction to increase (brighten) exposure.
4. Compose the picture, press the shutter button down halfway, and press it down fully.
Effective Subjects and Set Values
Positive (+) Compensation
•Copying of printed text (black characters on white paper)
•Backlit portraits
•Very bright scenes (such as snowfields) and highly reflective subjects
•Shots made up predominantly of sky
Negative (-) Compensation
•Spotlit subjects, particularly against dark backgrounds
•Copying of printed text (white characters on black paper)
•Scenes with low reflectivity, such as shots of green or dark foliage
Backlight compensation Exposure compensation

BenQ DC 5530 User’s Manual
Using the DC C50 14
English
3.1.8. Capture Mode Setup
This menu is for setting the basic setting to be used for photography in the [ ], [ P],
[TV ], [ AV ], [ M], [ ], [ ], [ ] , [ ]photography modes.
Note
•While selecting “Backlight compensation capturing mode” , the EV value sets to +1.3 EV
automatically and setting of exposure compensation value is ignored.
•In “Exposure compensation”, the default value is “0.0EV”. The setting range is as follows:
-2.0 / -1.7 / -1.3 / -1.0 /- 0.7 / -0.3 / 0 (default) / +0.3 / +0.7/ +1.0 / +1.3 / +1.7 / +2.0
•Exposure Compensation cannot be set at [ ] mode.
•The ideal brightness sometimes cannot be obtained even if a large exposure value is set in
dark photographic conditions.
In this case, press the shutter button, and check the brightness in the preview image
(photographed still image).
1. Set the mode dial to one of [ ], [ P], [ TV ], [ AV ],
[M], [ ], [ ], [ ] , [ ] and power on the
camera.
2. Press the MENU button.
The menu screen is displayed.
3. Use the or !button to select the menu page.
4. Use the or !button to select the desired item
and press the SET button.
The options are displayed.
5. Use the or !button to select the desired setting
and press the SET button.
This saves the settings, and returns the display to
menu screen.
6. To exit the menu screen, press the MENU button.
The camera is now ready to take photographs.

BenQ DC 5530 User’s Manual
Using the DC C50
15
English
3.1.8.1. Picture Setting
The Picture Setting contains 5 items: Size, Quality, Sharpness, Contrast and Color.
The tables below show the approximate number of images that can be stored on Still
Image and Movie Image mode.
Still Image Mode
Quality mode
(Compression Rate)
Image Size 8MB 16MB 32MB 64MB 128MB 256MB 512MB
Fine (1/4) 5M(2560 x 1920) 2 6 13 27 55 105 222
3M(2048 x 1536) 4 10 22 46 93 177 374
1.2M(1280 x 960) 9 20 42 86 174 331 698
VGA(640 x 480) 31 69 145 298 602 1147 2417
Standard (1/8) 5M(2560 x 1920) 4 10 22 46 93 177 374
3M(2048 x 1536) 8 17 36 74 150 286 604
1.2M(1280 x 960) 15 34 72 149 301 572 1208
VGA(640 x 480) 48 100 210 430 870 155307 3491
Economy (1/16) 5M(2560 x 1920) 9 20 42 86 174 331 698
3M(2048 x 1536) 15 34 72 149 301 572 1208
1.2M(1280 x 960) 28 60 126 258 522 994 2094
VGA(640 x 480) 91 181 379 775 1566 2984 6284
Size
Set the desired image size.
[2560 x 1920]: 2560 x 1920 pixels
[2048 x 1536]: 2048 x 1536 pixels
[1280 x 960]: 1280 x 960 pixels
[640 x 480]: 640 x 480 pixels
Note
•In the [ ] mode, image size available in this setting is 320 x 240 pixels and
160 x 120 pixels.
Quality
Set the quality (compression ratio) sharpness at
which the image is to be recorded.
[Fine]: 1/4compression(still image)/1/10
compression(video clip)
[Standard]: 1/8 compression(still image)/1/14
compression(video clip)
[Economy]: 1/16 compression(still image)/1/19
compression(video clip)

BenQ DC 5530 User’s Manual
Using the DC C50 16
English
Movie Image Mode
Quality mode
(Compression Rate)
Image Size Photography time (sec.)(max.)
Fine (1/10) FULL (320 x 240) 30
HALF (160 x 120) 90
Standard (1/14) FULL (320 x 240) 45
HALF (160 x 120) 120
Economy (1/19) FULL (320 x 240) 60
HALF (160 x 120) 180
Note
•The above data shows the standard testing results. The actual capacity varies
according to the shooting conditions and settings.
Sharpness
Set the level of the image sharpness.
[Hard]: Hard effect
[Normal] : Normal sharpness (default)
[Soft]: Soft effect
Note
•This function is not available in the [ ] mode.
Contrast
Set the contrast of the image to be photographed.
[Hard]: Hard contrast
[Normal] : Automatic (standard)
setting(default)
[Soft]: Soft contrast
Color
Set the color of the images to be photographed.
[Standard]: Standard color (default)
[Vivid] : Vivid color
[Sepia]: Sepia
[Monochrome]: Black and white