BenQ SH Series Operating instructions

English
SH/VH/VB Series LCD Display
TV Tuner Box and Remote Control
Installation and Operation Guide

English
Disclaimer
This company makes no representations or warranties, either expressed or
implied, with respect to the contents of this document. This company reserves
the right to revise this publication and to make changes from time to time in
the contents thereof without obligation to notify any person of such revision
or changes.
Copyright
All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any
language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written permission of this company.
This guide is written for the SH, VH and VB series LCD displays. The
descriptions of functions are common to all these series displays unless
indicated by (SH series), (VH series) or (VB series) in this guide, which
means that the function or term is only available on the specific series
displays.

Table of Contents i
English
Package contents ..................................................... 1
Installing the TV tuner box ..................................... 1
Important safety precautions ........................................... 1
Installing the TV tuner box .............................................. 1
Activate the remote control .................................... 4
Installing batteries ............................................................ 4
Battery safety notice .......................................................... 4
Getting to know the remote control ....................... 5
Using the remote control ........................................ 8
Power on, off and standby ............................................... 8
Turning the display on .........................................................8
Putting the display to standby .............................................8
Turning the display off (SH series) .....................................8
Switching inputs ............................................................... 8
Viewing traditional (analog) or digital TV ..................... 9
Adjusting sound settings .................................................. 9
Adjusting the volume ...........................................................9
Mute setting ..........................................................................9
MTS (TV Sound selection) ..................................................9
Turning on/off the Surround sound effect .........................9
Selecting a preset EQ mode ..................................................9
Changing channels ........................................................... 10
Selecting a channel directly ..................................................10
Changing channels sequentially ..........................................10
Returning to the previous viewed channel ..........................10
Selecting favorite channels ...................................................10
Selecting a picture mode .................................................. 10
Using the PIP (Picture-In-Picture) function (SH/VH
series) ................................................................................. 11
Adjusting aspect ratio ....................................................... 12
Using the sleep timer ........................................................ 13
Adjusting backlight ........................................................... 13
Using the freeze function ................................................. 13
Displaying information .................................................... 13
Table of Contents

Table of Contentsii
English
On-Screen Display (OSD) menu ............................ 14
OSD structure ....................................................................14
Navigating the OSD menu ................................................16
Operations in the OSD menu ..............................................16
Audio menu .......................................................................17
Setting up Personal EQ Mode ............................................. 18
Picture menu (SH/VH series) ..........................................19
Picture menu (VB series) ..................................................20
Adjusting the contrast ..........................................................21
Adjusting the brightness ......................................................22
Setting up Personal Picture mode ....................................... 22
Senseye menu (SH series) .................................................23
Senseye menu (VB series) .................................................24
Feature menu (VH series) ................................................25
Window menu (SH/VH series) ........................................26
TV menu ............................................................................27
Searching and storing TV channels .....................................27
Setting up favorite channels ................................................27
Setup menu (SH/VH series) .............................................28
Setup menu (VB series) ....................................................29

Package contents 1
English
Package contents
Check the package to see if all the following items are included. If any item is
missing or damaged, contact your place of purchase immediately and notify
them of the discrepancy.
Installing the TV tuner box
Important safety precautions
Before installing the TV tuner box, pay attention to the following to ensure
the safety of installation:
• Wear suitable insulation gloves to prevent any possibilities of injuries.
• Be sure to turn the display power off and disconnect the power cord from the
power outlet. Turn the power of the devices off and remove all connected
signal cables if the display is connected to other devices.
• Make sure that there is sufficient space around the display for performing the
installation. If not, it is suggested that you move the display to a suitable place
to perform installation, and then move it back to its original location when
installation is completed.
Installing the TV tuner box
Screw × 1
TV tuner box × 1 Installation and operation guide × 1
1. Locate the TV tuner box slot on the left side
of the display (as shown in the illustration).
TV tuner box
slot

Installing the TV tuner box2
English
2. Remove the screw that secures the metal box
in the TV tuner box slot using a suitable
screwdriver.
3. Use the screwdriver to remove the metal box
from the slot and keep it in a safe place (for
example, places inaccessible to small
children).
4. Remove the protective film on the TV tuner
box and then insert it into the slot. Pay
attention to the direction of the TV tuner
box when inserting.
5. Push the TV tuner box all the way into the
slot.

Installing the TV tuner box 3
English
6. Use the supplied screw and a suitable
screwdriver to secure the TV tuner box on
the display.
7. Connect the cable TV or aerial antenna cable
to the TV cable connector on the TV tuner
box. Follow the instructions of "Searching
and storing TV channels" on page 27 to scan
and store the TV channels available in your
area.

Activate the remote control4
English
Activate the remote control
Installing batteries
Battery safety notice
The use of the wrong type of batteries may cause chemical leaks and/or
explosion. Please note the following:
• Always ensure that the batteries are inserted with the positive and negative
terminals in the correct direction as shown in the battery compartment.
• Different types of batteries have different characteristics. Do not mix
different types.
• Do not mix old and new batteries. Mixing old and new batteries will shorten
battery life and/or cause chemical leaks from the old batteries.
• When batteries fail to function, replace them immediately.
• Chemicals which leak from batteries may cause skin irritation. If any
chemical matter seeps out of the batteries, wipe it up immediately using a dry
cloth.
• Due to varying storage conditions, the battery life for the batteries included
with your display may be shortened. Replace them within 3 months or as
soon as you can after initial use.
1. Turn the remote control to reveal its back side,
and open the lid of the battery compartment.
2. Insert the batteries (supplied) ensuring that
the positive and negative marked battery
terminals match the (+) and (-) marks in the
battery compartment. Note that these batteries
are provided for your convenience so that you
can operate the display straight away. You
should replace them as soon as possible.
3. Refit the lid of the battery compartment as
shown.

Getting to know the remote control 5
English
Getting to know the remote control
1. Power/standby
Press this button to power the display on or put it to
standby mode. See "Power on, off and standby" on
page 8.
2. 訊號來源 (Input)
Press this button to select a different input source. See
"Switching inputs" on page 8.
3. 電視 /數位電視 (TV/DTV)
Press this button to switch directly to the (traditional)
analog TV mode to view TV or CATV channels, or to
the digital TV mode and view digital TV channels (A
separate DTV tuner is required to use this function).
See "Viewing traditional (analog) or digital TV" on
page 9.
4. 定時關機 (Sleep Timer)
Press this button to set the automatic shut-off timer.
See "Using the sleep timer" on page 13.
5. 畫面靜止 (Freeze)
Press this button to freeze the image on the screen.
Press the button again to resume viewing in real time.
See "Using the freeze function" on page 13.
6. 畫面比例 (Aspect)
Press this button to adjust the screen image aspect
ratio. See "Adjusting aspect ratio" on page 12.
7. 背光亮度 (Backlight)
Press this button to select your desired screen
backlight level. See "Adjusting backlight" on page 13.
8. Senseye
Press this button to display the Senseye menu. See
"Senseye menu (SH series)" on page 23 and "Senseye
menu (VB series)" on page 24.
9. 影像模式 (Picture Mode)
Press this button to select a desired preset picture
mode. See "Selecting a picture mode" on page 10.
10. 子母畫面 (Picture In Picture)(SH/VH
series)
Press this button to simultaneously view signals from
two different sources on-screen. See "Using the PIP
(Picture-In-Picture) function (SH/VH series)" on
page 11.
11. 雙語 (MTS)
Press this button to toggle between available sound
reception modes. See "MTS (TV Sound selection)" on
page 9.

Getting to know the remote control6
English
12. 音場效果 (EQ Mode)
Press this button to select from preset EQ modes. See
"Selecting a preset EQ mode" on page 9.
13. Channel selection
Press these buttons to select the channel you wish to
view. See "Selecting a channel directly" on page 10.
14. 返回 (Recall)
Press this button to toggle between the current and
the previous channel you were viewing. See
"Returning to the previous viewed channel" on page
10.
15. 節目導覽 (EPG)
In DTV mode, press this button to display the
Electronic Program Guide (A separate DTV tuner is
required to use this function).
16. 喜愛頻道 (Favorite)
Press this button to jump to one of the favorite
channels you have stored. See "Selecting favorite
channels" on page 10.
17. 資訊顯示 (Information)
Press this button to display the input source
information. See "Displaying information" on page
13.
18. //+/- and OK buttons
When the OSD menu is not visible:
• Pressor to sequentially change channels.
• Press + or - to adjust speaker volume.
• In digital TV mode, press the OK button to display
or hide the channel list (A separate DTV tuner is
required to use this function).
When the OSD menu displays on-screen:
• Pressor to select settings.
• Press + or -to adjust settings.
• Press the OK button to execute selections, or to enter
a submenu you have selected.
See "Navigating the OSD menu" on page 16.
19. 目錄 (Menu)
Press this button to display the OSD menu for
commands and settings. Press it again to close. See
"Navigating the OSD menu" on page 16.
20. 回上頁 (Back)
When operating in the OSD menu, press this button
to return to the previous menu level. See "Navigating
the OSD menu" on page 16.

Getting to know the remote control 7
English
21. Red button
In DTV mode, press this button to execute the
function as indicated by the red color in the menu (A
separate DTV tuner is required to use this function).
22. Green button
In DTV mode, press this button to execute the
function as indicated by the green color in the menu
(A separate DTV tuner is required to use this
function).
23. Yellow button
In DTV mode, press this button to execute the
function as indicated by the yellow color in the menu
(A separate DTV tuner is required to use this
function).
24. Blue button
In DTV mode, press this button to execute the
function as indicated by the blue color in the menu
(A separate DTV tuner is required to use this
function).
25. 環繞音效 (Surround)
Press this button to turn on or off the Surround
sound effect. See "Turning on/off the Surround sound
effect" on page 9.
26. 音量 (Volume)
Press these buttons to raise or lower the volume level.
See "Adjusting the volume" on page 9.
27. 頻道 (Channel)
• Press these buttons to sequentially change channels.
See "Changing channels sequentially" on page 10.
• In DTV EPG, press these buttons to go to the
previous or next page (A separate DTV tuner is
required to use this function).
28. 靜音 (Mute)
Press this button to mute the sound output. Press it
again to restore the sound output. See "Mute setting"
on page 9.

Using the remote control8
English
Using the remote control
• Do not cover the sensor window on the front of the display (below the power
indicator lamp), or place objects in front of it which will block the direct line-
of-sight between the remote control and the sensor window.
• Do not let the remote control become wet, or place it in humid environments
(like bathrooms.)
• If the remote control sensor window on the display is in direct sunlight or
strong light, the remote control may not operate properly. In this situation,
change the light source or readjust the angle of your display, or operate the
remote control from a location closer to the remote control sensor window.
Power on, off and standby
Turning the display on
After plugging the display's power cable into a wall outlet and turning on the
main power switch, the display will enter standby mode automatically, and the
power indicator will light up red. Press Power/standby on the remote
control. The display will turn on and the power indicator will change to green.
Putting the display to standby
When the display power is ON (the power indicator lights up green), press
Power/standby on the remote control, and the display will return to
standby mode. The power indicator will turn red.
The display still consumes about 1W (VH series)/1.5W (SH/VB series) of power in
standby mode.
Turning the display off (SH series)
You can turn the display power off by flipping the main power switch on the
display to the off (O) position. The power indicator will be off.
Switching inputs
1. Turn on the display. Turn on the connected device and play the video.
2. Press 訊號來源 (Input) on the remote control to display the current selected
input. Press the button repeatedly until your desired input is displayed.
The sequence is as follows:
• Point and aim the top front of the
remote control directly at the display
when pressing the buttons.
• The remote control must be held at an
angle within 30 degrees of the display's
remote control sensor window to
function correctly. The distance
between the remote control and the
sensors should not exceed 6 meters.
6 meters
30 degrees
VB series AT V AV 1 AV2 ( o r AV 2 - S ) H D M I ( o r DV I )
DTV PC ATV...
VH series AV1 AV2 AV3 (or AV3-S) AV4 (or AV4-S)
HDMI (or DVI) PC AV1...
SH series AV1 AV2 AV3 (or AV3-S) HDMI1(or DVI)
HDMI2 (or DVI) PC AV1...

Using the remote control 9
English
• These options will only appear when corresponding signals are connected to
the display. DTV will only appear when the optional DTV tuner is installed.
• If both Composite Video (AV) and S-Video signals are connected to the AV input
at the same time, only S-Video input will be displayed. If you wish to view the
Composite Video (AV) input in such case, remove the S-Video connection
temporarily.
• Be aware that the HDMI input signal must be HDCP-compliant to be displayed
properly. When switching to the HDMI inputs, the display needs approximately 3
seconds to detect the HDCP information from the signal source and no image
will be displayed during this period. This is not a malfunction.
• When displaying PC video, remember to switch the PC video output setting
from monitor display to external device. For more information, refer to the
documentations of your PC.
Viewing traditional (analog) or digital TV
You can press 電視 /數位電視 (TV/DTV) on the remote control to directly
switch to the traditional (analog) TV mode and view TV or CATV programs,
or press it once more to switch to the digital TV mode and view digital TV
programs.
The digital TV function requires a separate DTV tuner with available digital TV
signal connected.
Adjusting sound settings
Adjusting the volume
• Press 音量 (Volume) + or +on the remote control to increase volume. The
volume indicator will increase in length as volume rises.
• Press 音量 (Volume) - or - on the remote control to decrease volume. The
volume indicator will decrease in length as volume falls.
Mute setting
Press 靜音 (Mute) on the remote control to turn off the sound temporarily.
Press 靜音 (Mute) once more, or press 音量 (Volume) + or +to restore the
sound level.
MTS (TV Sound selection)
Press 雙語 (MTS) on the remote control to toggle TV sound among available
modes. (The modes available will depend on the TV or Video sound system
being received).
Turning on/off the Surround sound effect
You can press 環繞音效 (Surround) on the remote control to turn on or off
the display’s SRS TruSurround XT sound effect. The SRS TruSurround XT
sound technology makes it possible for the display to deliver true-to-life
sounds by simulating multi-channel audio output. It also helps to enhance
the clarity of verbal conversations.
Selecting a preset EQ mode
Press 音場效果 (EQ Mode) on the remote control to select a suitable EQ
(Equalizer) mode according to your preference.

Using the remote control10
English
Changing channels
Selecting a channel directly
• To select a single- or double-digit channel, press the corresponding channel
selection buttons on the remote control. For example, to select channel 8,
press 0and 8 on the remote control.
• To select a triple-digit channel, press 100+ on the remote control followed by
the rest of the digits. within 3 seconds For example, to select channel 120,
press 100+, and then press 2 and 0 on the remote control.
Changing channels sequentially
Press 頻道 (Channel) (or ) / 頻道 (Channel)(or) on the remote
control to sequentially cycle through your TV channels.
Returning to the previous viewed channel
You can press 返回 (Recall) on the remote control to quickly return to the
previous viewed channel.
Selecting favorite channels
Press 喜愛頻道 (Favorite) on the remote control to jump to your preset
favorite channel 1. Press the button again to jump to the next favorite
channel, and so on. You may select from up to 5 channels to set as your
favorites.
For more information about how to set up favorite channels, please refer to
"Setting up favorite channels" on page 27.
Selecting a picture mode
To select a picture mode, press 影像模式 (Picture Mode) on the remote
control. This enables you to select from the following settings:
See "Setting up Personal Picture mode" on page 22 for how to setup the
Personal Picture Mode.
Picture mode Description
Dynamic The contrast, brightness and color saturation are
enhanced for displaying vivid images in public areas.
Standard Suitable for viewing in environments with normal
lighting condition.
Cinema
In this mode, the contrast and levels of colors are
optimized in order to display more details in the bright
and dark areas of images.
Game (SH/VB
series)
Images are displayed with moderate brightness and
contrast, making it suitable for prolonged viewing.
Personal Your own customised picture mode.

Using the remote control 11
English
Using the PIP (Picture-In-Picture) function (SH/VH
series)
If the display is connected to either a TV antenna or Video image source, and
also to an active Graphic image source at the same time, you can display both
images on the screen simultaneously by using PIP (Picture-In-Picture) mode.
• PC or DVI must be selected as one of the input sources in PIP mode.
• In PIP mode, some of the remote control functions will be unavailable.
1. Press 訊號來源 (Input) on the remote control to select a Graphic image
source (PC or DVI) as the input source.
2. Press 子母畫面 (Picture In Picture) on the remote control to switch display
to PIP mode. Each press cycles the display through the following display
sequence:
• To change the input source for the sub picture, press 訊號來源 (Input).
The sub picture cannot display Component Video (AV1 and AV2) input signals.
• To change the position of the sub picture on the screen, press , , +or - on
the remote control.
• To select audio from the main or sub picture, see "PIP Audio" on page 26.
The table below shows the availability of the PIP function under different
Video and Graphic signal input combinations for the Main and Sub pictures.
In the table above:
• ○: The PIP function is available.
• – : The PIP function is unavailable and cannot be selected.
Full screen PIP mode Full screen
Main picture input
ATV DTV AV 1, AV 2
AV3
(AV3-S)/AV4
(AV4-S)
PC DVI HDMI
(VH series)
HDMI1,
HDMI2
(SH series)
Sub
picture
input
ATV －－ － － ○○ － －
DTV －－ － － ○○ － －
AV1, AV 2 －－ － － －－ － －
AV3
(AV3-S)/
AV4
(AV4-S)
－－ － － ○○ － －
PC －－ － － －－ － －
DVI －－ － － －－ － －
HDMI
(VH series) －－ － － －－ － －
HDMI1,
HDMI2
(SH series)
－－ － － －－ － －

Using the remote control12
English
Adjusting aspect ratio
The display can resize and reshape an image to suit your requirements. The
visual result will depend upon the setting your have chosen, and the original
aspect ratio of the input image. Press 畫面比例 (Aspect) on the remote
control to cycle through the aspect ratios. The table below shows the resulting
images in relation to the input image when different aspects are selected:
• Available aspect ratio options are dependent on the selected input signal type.
• When viewing 1080p input video signals, the aspect ratio is fixed as “16:9“ and
cannot be changed.
• When viewing PC, DVI and HDMI inputs, only “16:9“ and “4:3“ are available for
selection.
• To avoid possible "image retention“ or "screen burn-in“ on the LCD screen, it is
recommended that you change the aspect ratio from time to time, and prevent
the display from displaying a static image for a prolonged period of time.
Aspect
ratio
Aspect ratio of input video
Description and usage
4:3 16:9
16:9
Stretches a 4:3 image to 16:9 aspect
proportions. Recommended for use
when viewing video sources which are
already in 16:9 aspect such as digital
TV and most widescreen DVDs.
4:3 (Not
recommended)
Resizes the image to 4:3 aspect
proportions. Recommended for use
when viewing video sources which are
already in 4:3 aspect such as analog TV
and PC video input.
16:9 Adj.
(Adjust)
(Not
recommended)
Stretches a 4:3 image to 16:9 aspect
proportions and enlarges the resultant
image on the screen. You can press 
or on the remote control to pan the
enlarged image. Recommended for use
when viewing video sources which are
in 4:3 aspect such as analog TV input.
Letter
Box
(Not
recommended)
Resizes a 4:3 image to 16:9 aspect
proportions, and trims off the top and
bottom strips. Recommended for use
when viewing 4:3 aspect video
presenting compressed 16:9 aspect
images in a 4:3 aspect frame in a so-
called letterbox format (black strips
along the top and bottom).
Cinema (Not
recommended)
Stretches a 4:3 image to the width of a
16:9 aspect image proportions.
recommended for use in filling the
screen with a 4:3 aspect image.

Using the remote control 13
English
Using the sleep timer
The sleep timer is useful if you want the display to automatically to go into
standby mode after a set period of time.
1. Press 定時關機 (Sleep Timer) on the remote control to activate the sleep
timer function.
2. Press the button again to set the time interval.
For example, if you set the sleep timer to 30 minutes, the display will enter
standby mode after 30 minutes of time. You can check the remaining time
before expiration in the Sleep Timer item in the Setup menu (See "Sleep
Timer" on page 28). 1 minute before the expiration of the set time, a message
will display on-screen as a reminder. You can press any button on the remote
control to reset the sleep timer and the display will remain on. To turn off this
function, set the time to 0minute (SH/VH series) or Off (VB series).
Adjusting backlight
To adjust the intensity of your display's backlight system, press 背光亮度
(Backlight) on the remote control several times to select a suitable level (SH/
VH series), or press 背光亮度 (Backlight) on the remote control, and then
press +or - to make adjustment (VB series).
If Auto (SH/VH series) is selected, the ambient light sensor on the display will
be activated and the display’s backlight will be changed automatically
according to the ambient lighting condition.
Using the freeze function
Press 畫面靜止 (Freeze) on the remote control to freeze the image on the
screen. Press it again to restore normal viewing.
• This function does not control the input source which will continue normally,
but not be displayed whilst the image remains frozen. When the image freeze is
stopped, normal play will resume in real time. That is, the displayed image will
jump to the current time and any interim video is not displayed.
• In PIP mode, this function can only freeze the motion of the sub picture.
Do not leave the screen displaying a static image for an extended period of time
(days) as doing so may temporarily or permanently damage the screen resulting
in image traces which could remain visible long after the original image has been
removed.
Displaying information
Press 資訊顯示 (Information) on the remote control to display the input
signal information. The information displayed varies according to the input
source being selected.

On-Screen Display (OSD) menu14
English
On-Screen Display (OSD) menu
OSD structure
Input signal type
ATV DTV
AV1 (VB
series)
AV2/AV2-S
(VB series)
PC
DVI
(PC
mode)
DVI
(Video
mode)
HDMI
(VB/VH
series)
AV1, AV2
(SH/VH
series)
AV3/AV3-S
or AV4/
AV4-S (SH/
VH series)
HDMI1/
HDMI2
(SH
series)
Audio
• Volume
• Balance
• Sound Type
• Steady Sound
• Surround
• Speaker Out
• Advanced Audio Settings
Picture
(SH/VH
series)
• Picture Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color TEMP.
• NTSC Tint
• NTSC Setup
• Picture
Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color
TEMP.
• Picture
Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color
TEMP.
• NTSC Tint
• NTSC Setup
• Contrast
• Brightness
• Color
TEMP.
• Auto
• Frequency
• Phase
• H. Position
• V. Position
• Contrast
• Brightness
• Color TEMP.
• Picture
Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color
TEMP.
Picture
(VB
series)
• Picture Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color TEMP.
• Backlight
• NTSC Tint
• NTSC Setup
• Picture
Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color
TEMP.
• Backlight
• Picture
Mode
• Contrast
• Brightness
• Color
• Sharpness
• Color
TEMP.
• Backlight
• NTSC Tint
• NTSC Setup
• Contrast
• Brightness
• Color
TEMP.
• Backlight
• Auto Adjust
• Frequency
• Phase
• H. Position
• V. Position
• Contrast
• Brightness
• Color TEMP.
• Backlight
Senseye
(SH
series)
• Color Style
• Gamma Style
• ACE
• Noise Reduction
• Color Style
• Gamma Style
• ACE
Feature
(VH
series)
• Black Extension
• ACE
• Noise Reduction
• Aspect Ratio
• Aspect Ratio
Senseye
(VB
series)
• Black Extension
• ACE
• Noise Reduction
(Not available)
Window
(SH/VH
series)
(Not available)
• PIP
• Main Input
• Sub Input
• PIP Audio
(Not available)

On-Screen Display (OSD) menu 15
English
• The available menu items are dependent on the input source being selected.
Unavailable items will be greyed out or not displayed. For details see:
• Settings under different input sources can be adjusted independently. For
example, the Picture settings for the AV1 input will not affect the Picture
settings for the AV2 input.
Input signal type
ATV DTV
AV1 (VB
series)
AV2/AV2-S
(VB series)
PC
DVI
(PC
mode)
DVI
(Video
mode)
HDMI
(VB/VH
series)
AV1, AV2
(SH/VH
series)
AV3/AV3-S
or AV4/
AV4-S (SH/
VH series)
HDMI1/
HDMI2
(SH
series)
TV
• TV/CATV
• Channel +/-
• Favorite
Channels
• Auto
Program
• TV/Radio
• TV Guide
• Channel
List
• Channel
Editor
• Replace
Existing
Digital
Channels
• Add New
Digital
Channels
(Not available)
Setup
(SH/VH
series)
• Language
• Backlight
• Sleep Timer
• ECO
• HDMI/DVI Input (SH series)/DVI Input (VH series)
• Blue Screen (SH series)
• Reset All Settings
Setup
(VB
series)
• Language
• Sleep Timer
• ECO
• HDMI/DVI Input
• Blue Screen
• Reset All Settings
"Audio menu" on page 17
"Picture menu (SH/VH series)" on page 19
"Picture menu (VB series)" on page 20
"Senseye menu (SH series)" on page 23
"Senseye menu (VB series)" on page 24
"Feature menu (VH series)" on page 25
"Window menu (SH/VH series)" on page 26
"TV menu" on page 27
"Setup menu (SH/VH series)" on page 28
"Setup menu (VB series)" on page 29

On-Screen Display (OSD) menu16
English
Navigating the OSD menu
You can use the On-Screen Display (OSD) menu to adjust the settings on
your display. To display the OSD menu, press 目錄 (Menu) on the remote
control (the main OSD menu of the SH series display is shown below):
Operations in the OSD menu
• Press , , +or - to make selections or change settings.
• Press OK to confirm your selection or enter an submenu (if available).
• Press 回上頁 (Back) to return to the previous menu level.
• Press 目錄 (Menu) to close the OSD menu.
For example, to adjust picture sharpness:
Audio Window TV Setup
Senseye
Picture
1. Press MENU to display the OSD menu on-screen.
2. Press +or - to select Picture.
3. Press OK to enter the submenu.
4. Press or to select Sharpness.
5. Press +or - to make adjustment.
6. Press 回上頁 (Back) to return to the previous menu level, or
7. Press 目錄 (Menu) to close the OSD menu.