BenQ PX9210 User manual

PX9210 / PU9220 / PU9220+
Digital Projector
Installation Guide

English
2
Table of Contents
Product information ............................................................................. 3
Lens information ................................................................................... 3
Notice (when edge blending) ............................................................... 3
Product information ............................................................................. 4
Lens shift range ..................................................................................... 6
Projector dimensions............................................................................ 8
Clearance around the exhaust vent .................................................... 9
Lens dimensions .................................................................................... 10
Ceiling mount dimensions.................................................................... 12
IO panel.................................................................................................. 13
RS232 command ................................................................................... 14
2015/ 8/ 3

English
3
Product information
Type: DLP™ Technology
Dimensions (W x H x D): 431 x 167 x 320.5 mm
Weight: 8.5 kg (18.7 lbs)
Specications PX9210 PU9220/PU9220+
DMD size 0.7˝ 0.67˝
Native resolution XGA (1024 x 768) WUXGA (1920 x 1200)
Aspect ratio 4:3 16:10
Brightness 6000 Lumens 5000 Lumens
Lamp Wattage 370W
Power consumption(Max) 480W
Lens information
Model Name Lens Type BenQ Part Number Optical Spec Screen Size
LS2ST3 Wide x 5J.JDH37.001 F=2.5, f=11.5mm 80˝~180˝
LS2ST1 Wide zoom 5J.JDH37.011 F=2.05~2.27, f=16.64~19.5 mm 80˝~350˝
LS2SD Standard 5J.JDH37.021 F=2.46~2.56, f=22.8~28.5mm 80˝~210˝
LS2LT1 Semi Long 5J.JDH37.031 F=2.5~3.1, f=28.5~42.75mm 80˝~480˝
LS2LT2 Long zoom 1 5J.JDH37.041 F=2.2~2.5, f=44.5~74.19mm 80˝~300˝
Notice (when edge blending)
• To avoid the image shaking or some pixels in the display may be misaligned, do not use the projector in the
following location:
• In a building close to a construction site.
• In a room where an air conditioner unit is working and it vibrates.
• In a place where the temperature changes dramatically that may cause thermal contraction.
• Before making any adjustment, leave the projector lit for at least 45 minutes after its lamp is turned on. This allows
the internal temperature of the projector to stabilize.

English
4
Product information
PX9210 Formulas:
Denitions:
W = Image Width
H = Image Height (size)
C = Throw distance
4:3 Screen Formulas:
W = H x 4/3
H = W x 3/4
Diagonal = W x 5/4
PX9210
Part Number 5J.JDH37.001 5J.JDH37.011 5J.JDH37.021 5J.JDH37.031
Throw Ratio
LS2ST3
(Wide Fix Lens)
LS2ST1
(Wide Zoom Lens)
LS2SD
(Standard Lens)
LS2LT1
(Semi Long Lens)
0.8 1.14-1.35 1.6-2.0 2.0-3.0
Diagonal Width Height (B) N/A Wide Tele Wide Tele Wide Tele
(inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m)
80 2.03 64 1.63 48 1.22 51 1.3 73 1.85 86 2.18 102 2.6 128 3.25 128 3.25 192 4.88
100 2.54 80 2.03 60 1.52 64 1.63 91 2.32 107 2.72 128 3.25 160 4.06 160 4.06 240 6.1
120 3.05 96 2.44 72 1.83 77 1.95 109 2.78 129 3.27 154 3.9 192 4.88 192 4.88 288 7.32
150 3.81 120 3.05 90 2.29 96 2.44 137 3.47 161 4.08 192 4.88 240 6.1 240 6.1 360 9.14
200 5.08 160 4.06 120 3.05 - - 182 4.63 214 5.45 256 6.5 320 8.13 320 8.13 480 12.19
300 7.62 240 6.1 180 4.57 - - 274 6.95 322 8.17 - - - - 480 12.19 720 18.29
400 10.16 320 8.13 240 6.1 - - - - - - - - - - 640 16.26 960 24.38
500 12.7 400 10.16 300 7.62 - - - - - - - - - - - - - -
Part Number 5J.JDH37.041
Throw Ratio
LS2LT2
(Long Zoom Lens)
3.11-5.18
Diagonal Width Height (B) Wide Tele
(inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m)
80 2.03 64 1.63 48 1.22 199 5.06 332 8.42
100 2.54 80 2.03 60 1.52 249 6.32 414 10.53
120 3.05 96 2.44 72 1.83 299 7.58 497 12.63
150 3.81 120 3.05 90 2.29 373 9.48 622 15.79
200 5.08 160 4.06 120 3.05 498 12.64 829 21.05
300 7.62 240 6.1 180 4.57 746 18.96 1243 31.58
400 10.16 320 8.13 240 6.1 - - - -
500 12.7 400 10.16 300 7.62 - - - -

English
5
PU9220/PU9220+ Formulas:
Denitions:
W = Image Width
H = Image Height (size)
C = Throw distance
16:10 Screen Formulas:
W = H x 16/10
H = W x 10/16
Screen Diagonal = W x 18.868/16
PU9220/PU9220+
Part Number 5J.JDH37.001 5J.JDH37.011 5J.JDH37.021 5J.JDH37.031
Throw Ratio
LS2ST3
(Wide Fix Lens)
LS2ST1
(Wide Zoom Lens)
LS2SD
(Standard Lens)
LS2LT1
(Semi Long Lens)
0.77ST 1.1~1.3 1.54~1.93 1.93~2.9
Diagonal Width Height (B) N/A Wide Tele Wide Tele Wide Tele
(inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m)
80 2.03 68 1.72 42 1.08 52 1.33 75 1.9 88 2.24 104 2.65 131 3.33 131 3.33 197 5
100 2.54 85 2.15 53 1.35 65 1.66 93 2.37 110 2.8 131 3.32 164 4.16 164 4.16 246 6.25
120 3.05 102 2.58 64 1.62 78 1.99 112 2.84 132 3.36 157 3.98 196 4.99 196 4.99 295 7.5
150 3.81 127 3.23 79 2.02 98 2.49 140 3.55 165 4.2 196 4.98 245 6.24 245 6.24 369 9.37
200 5.08 170 4.31 106 2.69 - - 187 4.74 220 5.6 261 6.63 327 8.31 327 8.31 492 12.49
300 7.62 254 6.46 159 4.04 - - 280 7.11 331 8.4 - - - - 491 12.47 738 18.74
400 10.16 339 8.62 212 5.38 - - - - - - - - - - 655 16.63 984 24.99
500 12.7 424 10.77 265 6.73 - - - - - - - - - - - - - -
Part Number 5J.JDH37.041
Throw Ratio
LS2LT2
(Long Zoom Lens)
3~5
Diagonal Width Height (B) Wide Tele
(inch) (m) (inch) (m) (inch) (m) (inch) (m) (inch) (m)
80 2.03 68 1.72 42 1.08 204 5.17 339 8.62
100 2.54 85 2.15 53 1.35 254 6.46 424 10.77
120 3.05 102 2.58 64 1.62 305 7.75 509 12.92
150 3.81 127 3.23 79 2.02 382 9.69 636 16.15
200 5.08 170 4.31 106 2.69 509 12.92 848 21.54
300 7.62 254 6.46 159 4.04 763 19.39 1272 32.31
400 10.16 339 8.62 212 5.38 - - - -
500 12.7 424 10.77 265 6.73 - - - -
Note:
• Ceiling installation must be done by a qualied professional. Contact your dealer for more information. It is not
recommended you install the projector yourself.
• Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.
• Do not use the projector in an environment where extreme temperature occurs.The projector must be used at
temperatures between 41 degrees Fahrenheit (5 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius).
• Screen damage will occur if the projector is exposed to moisture, dust or smoke.
• Do not cover the vents on the projector. Proper ventilation is required to dissipate heat. Damage to the projector
will occur if the vents are covered.

English
6
Lens shift range
Lens shift adjustable range
The adjustable range for lens shift is tabulated below and subject to the conditions listed.
Note:
The drawings below apply to the standard lens only.
XGA
Desk-Front Projection
Vertical Shift
Normal projection position
Max 0.1V
1V
1V
0.05H
Shift to Left Shift to Right
0.05H
Max
0.5V
Height of projected image
Height of projected image
Width of projected image
1H
Vertical Shift
Ceiling Mount-Front Projection
Vertical Shift
Max 0.5V

English
7
WUXGA
Desk-Front Projection
Vertical Shift
Normal projection position
Max 0.15V
1V
1V
0.05H
Shift to Left Shift to Right
0.05H
Max
0.55V
Height of projected image
Height of projected image
Width of projected image
1H
Vertical Shift
Ceiling Mount-Front Projection
Vertical Shift
Max 0.55V
Ceiling Mount Installation
Screen Top
H
CX
0.1H
No Offset from Mount Pipe
X = Distance from lens to mount center
C = Distance from lens to screen
Only for Lenses:
LS2ST3: X = 176.3
LS2ST1: X = 255.8
LS2SD: X = 190.9
LS2LT1: X = 205.5
LS2LT2: X = 235.5
Shift Range
Screen Center

English
8
Projector dimensions
431.9
220.0
110.0
321.0 55.5
216.0
174.5
83.0
56.0
82.5
221.0
316.9
AIR INLET
AIR EXHAUST
AIR EXHAUST
M4X12L
260.0
54.0192.0
283.0

English
9
Clearance around the exhaust vent
For proper ventilation of the projector, make sure to leave some space around the projector as
shown in the illustration below:
Min. 500mm Min. 500mm
Min. 500mm
Min. 500mm
Min. 300mm

English
10
Lens dimensions
Optional Lens (Wide Fix: LS2ST3)
LS2ST3,Wide Fix lens
316.9 334.4
Optional Lens (Wide Zoom: LS2ST1)
LS2ST1,Wide Zoom lens
316.9 413.9
Optional Lens (Standard: LS2SD)
LS2SD, Standard lens
316.9 349.0

English
11
Optional Lens (Semi Long Throw: LS2LT1)
LS2LT1, Semi Long Throw lens
316.9 363.6
Optional Lens (Long Throw 1: LS2LT2)
LS2LT2, Long Throw 1 lens
316.9 393.6

English
12
Ceiling mount dimensions
324
324
12
12
12
35
12 12
150150
12
12
12
162 162
162 162
Ceiling Mount (Part Number: 5J.JCY10.001)
±20°
Note:
• Mark A: PW9500/PX9600
• Mark B: PU9730/PX9710/PW9620
• Mark C: PX9210/PU9220

English
13
IO panel
• HDMI
Connection to HDMI source.
• DVI-D
Connection to DVI source.
• DisplayPort
Connection to device or PC featuring DisplayPort.
• LAN
Connection to network (via router/access point).
• USB (Type A)
Support 5V/1.5A output.
• 3D Sync Out
Connection to 3D IR sync signal transmitter.
• Computer-1/Computer-2
15-pin VGA port for connection to RGB, component HD source, or PC.
• Audio In-1/Audio In-2/Audio In-3/Audio In-4
Connection to an audio input source via an audio or audio L/R cable.
• Monitor Out
Connection to other display equipment for concurrent playback display.
• Audio Out
Connection to a speaker or headset.
• Computer-3 (R/Pr, G/Y, B/Pb, H,V)
Connection to RGB or YPbPr/YCbCr output signal with BNC type input terminal.
• Component/S-Video/Video
Connection to a video source.
• USB (Type B)
Connection to a PC using a USB cable.
• RS-232
Standard 9-pin D-sub interface for connection to PC control system and projector maintenance.
• TRIGGER
3.5mm mini earphone jack, employs 350mA display relay to provide 12(+/-1.5)V output and
short circuit protection.
• Wired Remote
Connection to input Niles or Xantech compatible IR repeater system.

English
14
Caution:
Make sure the port is valid before inserting a wired remote controller. The remote controller may be damaged in
case of an invalid port, e.g. a wired remote controller is connected to trigger output.
RS232 command
RS232 pin assignment
12345
6789
PIN Signal
1 NC (Data carrier detect)
2 RX (Receive data)
3 TX (Transmit data)
4 NC (Data terminal ready)
5 GND (Signal ground)
6 NC (Data set ready)
7 RTSZ (Request to send)
8 CTSZ (Clear to send)
9 NC (Ring indicator)
Function Type Description ASCII
Power
Write Power On <CR>*pow=on#<CR>
Write Power off <CR>*pow=off#<CR>
Read Power Status <CR>*pow=?#<CR>
Source
Selection
Write COMPUTER/YPbPr <CR>*sour=RGB#<CR>
Write COMPUTER 2/YPbPr2 <CR>*sour=RGB2#<CR>
Write COMPUTER 3/YPbPr3 <CR>*sour=RGB3#<CR>
Write Component <CR>*sour=ypbr#<CR>
Write DVI-D <CR>*sour=dvid#<CR>
Write HDMI/MHL <CR>*sour=hdmi#<CR>
Write Composite <CR>*sour=vid#<CR>
Write S-Video <CR>*sour=svid#<CR>
Write DisplayPort <CR>*sour=dp#<CR>
Read Current source <CR>*sour=?#<CR>
Audio
Control
Write Mute On <CR>*mute=on#<CR>
Write Mute Off <CR>*mute=off#<CR>
Read Mute Status <CR>*mute=?#<CR>
Write Volume + <CR>*vol=+#<CR>
Write Volume - <CR>*vol=-#<CR>

English
15
Function Type Description ASCII
Audio source
select
Read Volume Status <CR>*vol=?#<CR>
Write Audio pass Through off <CR>*audiosour=off#<CR>
Write Audio-Computer1 <CR>*audiosour=RGB#<CR>
Write Audio-Computer2 <CR>*audiosour=RGB2#<CR>
Write Audio-Video/S-Video <CR>*audiosour=vid#<CR>
Audio source
select
Write Audio-Component <CR>*audiosour=ypbr#<CR>
Write Audio-HDMI <CR>*audiosour=hdmi#<CR>
Read Audio pass Status <CR>*audiosour=?#<CR>
Picture
Mode
Write Dynamic
<CR>*appmod=dynamic#<CR>
Write Presentation <CR>*appmod=preset#<CR>
Write sRGB <CR>*appmod=srgb#<CR>
Write Cinema <CR>*appmod=cine#<CR>
Write User1 <CR>*appmod=user1#<CR>
Write User2 <CR>*appmod=user2#<CR>
Read Picture Mode <CR>*appmod=?#<CR>

English
16
Function Type Description ASCII
Picture
Setting
Write Contrast + <CR>*con=+#<CR>
Write Contrast - <CR>*con=-#<CR>
Read Contrast value <CR>*con=?#<CR>
Write Brightness + <CR>*bri=+#<CR>
Write Brightness - <CR>*bri=-#<CR>
Read Brightness value <CR>*bri=?#<CR>
Write Color + <CR>*color=+#<CR>
Write Color - <CR>*color=-#<CR>
Read Color value <CR>*color=?#<CR>
Write Sharpness + <CR>*sharp=+#<CR>
Write Sharpness - <CR>*sharp=-#<CR>
Read Sharpness value <CR>*sharp=?#<CR>
Write Color Temperature-Warm <CR>*ct=warm#<CR>
Write Color Temperature-Normal <CR>*ct=normal#<CR>
Write Color Temperature-Cool <CR>*ct=cool#<CR>
Read Color Temperature Status <CR>*ct=?#<CR>
Write Aspect 4:3 <CR>*asp=4:3#<CR>
Write Aspect 16:9 <CR>*asp=16:9#<CR>
Write Aspect 16:10 <CR>*asp=16:10#<CR>
Write Aspect Auto <CR>*asp=AUTO#<CR>
Read Aspect Status <CR>*asp=?#<CR>
Write Digital Zoom In <CR>*zoomI#<CR>
Write Digital Zoom out <CR>*zoomO#<CR>
Write Auto <CR>*auto#<CR>
Write Brilliant color on <CR>*BC=on#<CR>
Write Brilliant color off <CR>*BC=off#<CR>
Read Brilliant color status <CR>*BC=?#<CR>

English
17
Function Type Description ASCII
Operation
Settings
Write Projector Position-Front Table <CR>*pp=FT#<CR>
Write Projector Position-Rear Table <CR>*pp=RE#<CR>
Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR>
Write Projector Position-Front Ceiling <CR>*pp=FC#<CR>
Write Quick auto search - on <CR>*QAS=on#<CR>
Write Quick auto search - off <CR>*QAS=off#<CR>
Read Quick auto search status <CR>*QAS=?#<CR>
Read Projector Position Status <CR>*pp=?#<CR>
Write Direct Power On-on <CR>*directpower=on#<CR>
Write Direct Power On-off <CR>*directpower=off#<CR>
Read Direct Power On-Status <CR>*directpower=?#<CR>
Write Signal Power On-on <CR>*autopower=on#<CR>
Write Signal Power On-off <CR>*autopower=off#<CR>
Read Signal Power On-Status
<CR>*autopower=?#<CR>
Write Standby Settings-Network on <CR>*standbynet=on#<CR>
Write Standby Settings-Network off
<CR>*standbynet=off#<CR>
Read Standby Settings-Network Sta-
tus <CR>*standbynet=?#<CR>
Write Standby Settings-Monitor Out
on <CR>*standbymnt=on#<CR>
Write Standby Settings-Monitor Out
off <CR>*standbymnt=off#<CR>
Read Standby Settings-Monitor Out
Status <CR>*standbymnt=?#<CR>
Baud Rate
Write 2400 <CR>*baud=2400#<CR>
Write 4800 <CR>*baud=4800#<CR>
Write 9600 <CR>*baud=9600#<CR>
Write 14400 <CR>*baud=14400#<CR>
Write 19200 <CR>*baud=19200#<CR>
Write 38400 <CR>*baud=38400#<CR>
Write 57600 <CR>*baud=57600#<CR>
Write 115200 <CR>*baud=115200#<CR>
Read Current Baud Rate <CR>*baud=?#<CR>
Lamp
Control
Read Lamp Hour <CR>*ltim=?#<CR>
Write Normal mode <CR>*lampm=lnor#<CR>
Write Eco mode <CR>*lampm=eco#<CR>
Read Lamp Mode Status <CR>*lampm=?#<CR>

English
18
Function Type Description ASCII
Miscellaneous
Read Model Name <CR>*modelname=?#<CR>
Write Blank On <CR>*blank=on#<CR>
Write Blank Off <CR>*blank=off#<CR>
Read Blank Status <CR>*blank=?#<CR>
Write Freeze On <CR>*freeze=on#<CR>
Write Freeze Off <CR>*freeze=off#<CR>
Read Freeze Status <CR>*freeze=?#<CR>
Write Menu On <CR>*menu=on#<CR>
Write Menu Off <CR>*menu=off#<CR>
Write Up <CR>*up#<CR>
Write Down <CR>*down#<CR>
Write Right <CR>*right#<CR>
Write Left <CR>*left#<CR>
Write Enter <CR>*enter#<CR>
Write 3D Sync Off <CR>*3d=off#<CR>
Write 3D Auto <CR>*3d=auto#<CR>
Write 3D Sync Top Bottom <CR>*3d=tb#<CR>
Write 3D Sync Frame Sequential <CR>*3d=fs#<CR>
Write 3D Frame packing <CR>*3d=fp#<CR>
Write 3D Side by side <CR>*3d=sbs#<CR>
Write 3D inverter disable <CR>*3d=da#<CR>
Write 3D inverter <CR>*3d=iv#<CR>
Read 3D Sync Status <CR>*3d=?#<CR>
Write Remote Receiver-front+rear <CR>*rr=fr#<CR>
Write Remote Receiver-front <CR>*rr=f#<CR>
Write Remote Receiver-rear <CR>*rr=r#<CR>
Read Remote Receiver Status <CR>*rr=?#<CR>
Write Instant On-on <CR>*ins=on#<CR>
Write Instant On-off <CR>*ins=off#<CR>
Read Instant On Status <CR>*ins=?#<CR>

English
19