BenQ WI 1000H8060 User manual

1
English
Table of Contents
Important safety instructions .............................................................................................. 2
Product information ............................................................................................................. 4
Shipping contents ....................................................................................................................................... 4
Specifications ............................................................................................................................................... 4
Projector dimensions ................................................................................................................................ 5
Terminals ...................................................................................................................................................... 5
Remote control........................................................................................................................................... 6
Installation ............................................................................................................................. 7
Projection dimensions ............................................................................................................................... 7
Shifting the projection lens....................................................................................................................... 8
Ceiling mount installation diagram ......................................................................................................... 9
Using the cable tie set ............................................................................................................................. 10
RS232 command ................................................................................................................. 11
RS232 pin assignment ..............................................................................................................................11

2
English
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information technology
equipment. However, to ensure safe use of this product, it is important that you follow the instructions
mentioned in the user manual / installation guide and marked on the product.
1. Please read the user manual / installation guide before you operate your projector. Save
it for future reference.
2. Do not look straight at the projector lens during operation. The intense light beam may
damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter (if any) or remove the lens cap (if any) when the
projector light source is on.
5. The light source becomes extremely hot during operation.
6. In some countries, the line voltage is NOT stable. This projector is designed to operate safely
within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10
volts occur. In areas where the mains voltage may fluctuate or cut out, it is
recommended that you connect your projector through a power stabilizer, surge
protector or uninterruptible power supply (UPS).
7. Do not block the projection lens with any objects when the projector is under operation as this
could cause the objects to become heated and deformed or even cause a fire. To temporarily turn
off the light source, use the blank function.
8. Do not operate light sources beyond the rated light source life.
9. Never replace the lamp assembly or any electronic components unless the projector is unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining
serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may
cause death if you should come into contact with live parts.
Under no circumstances should you ever undo or remove any other covers. Refer servicing only to
suitably qualified professional service personnel.
12. Do not block the ventilation holes.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.
13. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to
back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.
14. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing
injury or resulting in damage to the projector.
15. Do not step on the projector or place any objects upon it. Besides probable physical damage to the
projector, doing so may result in accidents and possible injury.
16. When the projector is under operation, you may sense some heated air and odor from its
ventilation grill. It is a normal phenomenon and not a product defect.

3
English
17. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail.
If the projector does become wet, disconnect it from the power supply's power outlet and call
BenQ to have the projector serviced.
18. This product is capable of displaying inverted images for ceiling mount installation.
19. This apparatus must be earthed.
20. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the
projector.
- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the
projector's life span and darken the image.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
Cooling notice
Risk Group 2
1. According to the classification of photobiological safety of light
sources and light source systems, this product is Risk Group 2,
IEC 62471-5:2015.
2. Possibly hazardous optical radiation emitted from this product.
3. Do not stare at operating light source. May be harmful to the
eyes.
4. As with any bright source, do not stare into the direct beam.
Ventilation Caution for installation
Avoid using the projector in a
poorly ventilated or confined
space.
For proper ventilation of the projector, make sure to leave some
space around the projector as shown in the illustration below:
• Table • Table
• Ceiling • Stacking
POWER
TEMP
LAMP
Air inlet Air outlet
50 cm
above
70 cm
above
50 cm
above 50 cm
above
30 cm
above
50 cm
above
Minimum 100 mm

4
English
Product information
Shipping contents
Optional accessories
Specifications
Projector Remote control with
batteries Cable tie set x 3
Installation guide User manual CD Warranty card* Power cord
• The supplied accessories will be suitable for your region, and may differ from those illustrated.
• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
1. Spare lamp kit
2. Ceiling mount kit
3. RS232 cable
4. Anamorphic lens
5. BenQ DGD5 3D Glasses
Display system 1-CHIP DMD
Resolution 3840 x 2160 with XPR
2716 x 1528 without XPR
Light source 240 W lamp
Brightness 2200 Lumens
Power consumption 384 W (Max); < 0.5 W (Standby)
Weight 14.8 Kg (32.6 lbs)

5
English
Projector dimensions
470.7 mm (W) x 224.9 mm (H) x 564.7 mm (D)
Te r m i n a l s
• LAN (10/100M)
For connection to a RJ45 Cat5/Cat6
Ethernet cable to control the projector
through a network.
• IR IN
For use with an IR extender cable to
ensure better signal reception from the
remote control.
• PC
15-pin VGA port for connection to a RGB
source or PC.
• HDMI 1 (Version 2.0) and its cable tie hole
Connection to an HDMI (4K) source.
Connection to a cable tile set.
• HDMI 2 (Version 1.4a) and its cable tie hole
Connection to an HDMI source.
Connection to a cable tile set.
• USB MINI-B
For firmware upgrade only.
• 12V TRIGGER 1/2
Triggers external devices such as an electric screen
or light control, etc.
• RS232
Standard 9-pin D-sub interface for connection to a
PC control system and projector maintenance.
POWER
TEMP
LAMP
470.7
564.7 224.9
Unit: mm

6
English
Remote control
* This button is not available for this model.
On Off
AUTO
ASPECT
SOURCE
Up
Left
OK
BACK
3D
CONTRAST
PIC MODE
COLOR TEMP
GAMMA
SHARP
TEST PATTERN
DEFAULT
Right
Down
MENU
CINEMAMASTER
INVERT
DYNAMIC IRIS
LIGHT MODE
COLOR MANAGE
ECO BLANK
KEY LIGHT
No function*
HDR
BRIGHT
No function*

7
English
Installation
Projection dimensions
• The screen aspect ratio is 16:9 and the
projected picture is in a 16:9 aspect ratio
Screen size Distance from screen (mm) Lowest/
Highest lens position
(mm)
Diagonal
W (mm) H (mm)
Min length
Average
Max length
Inch mm (max.
zoom)
(min.
zoom)
80 2032 1771 996 2400 3000 3600 149
90 2286 1992 1121 2700 3375 4050 168
100 2540 2214 1245 3000 3750 4500 187
110 2794 2435 1370 3300 4125 4950 205
120 3048 2657 1494 3600 4500 5400 224
130 3302 2878 1619 3900 4875 5850 243
140 3556 3099 1743 4200 5250 6300 262
150 3810 3321 1868 4500 5625 6750 280
160 4064 3542 1992 4800 6000 7200 299
170 4318 3763 2117 5100 6375 7650 318
180 4572 3985 2241 5400 6750 8100 336
190 4826 4206 2366 5700 7125 8550 355
200 5080 4428 2491 6000 7500 9000 374
210 5334 4649 2615 6300 7875 9450 392
220 5588 4870 2740 6600 8250 9900 411
230 5842 5092 2864 6900 8625 10350 430
240 6096 5313 2989 7200 9000 10800 448
250 6350 5535 3113 7500 9375 11250 467
260 6604 5756 3238 7800 9750 11700 486
270 6858 5977 3362 8100 10125 12150 504
280 7112 6199 3487 8400 10500 12600 523
290 7366 6420 3611 8700 10875 13050 542
300 7620 6641 3736 9000 11250 13500 560
• To optimize your projection quality, we suggest doing the projection by following the values in the non-gray cells.
The values in the gray cells are for reference only.
• All measurements are approximate and may vary from the actual sizes.
BenQ recommends that if you intend to permanently install the projector, you should physically test the
projection size and distance using the actual projector in situ before you permanently install it, so as to make
allowance for this projector's optical characteristics. This will help you determine the exact mounting position so
that it best suits your installation location.
• Ceiling installation must be done by a qualified professional. Contact your dealer for more information. It is not
recommended you install the projector yourself.
• Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.
• Do not use the projector in an environment where extreme temperature occurs. The projector must be used at
temperatures between 32 degrees Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees
Celsius).
• Screen damage will occur if the projector is exposed to moisture, dust or smoke.
• Do not cover the vents on the projector. Proper ventilation is required to dissipate heat. Damage to the projector
will occur if the vents are covered.
LAN PC -
RS232
12V
TRIGGHER
IRIN
1
2
HDMI2 - USBMINIB
HDMI1
HDCP2.2
H
WProjection distance
Center of lens
Screen
16:9 Screen diagonal

8
English
Shifting the projection lens
The horizontal position The vertical position
The projection range
POWER
TEMP
LAMP
27%27%
1 screen width
LAN PC -
RS 232
12V
TRIGGHER
IRIN
1
2
HDMI2 - USBMINI B
HDMI1
HDCP2.2
65%
65%
1screenheight

9
English
Ceiling mount installation diagram
290
337
372.8
547.8 530.8
553.39
564.49
275.79
Ceiling mount screw: M6
(Max L = 25 mm; Min L = 20 mm)
Unit: mm

10
English
Using the cable tie set
The cable tie set helps prevent a cable plug from falling out of the connecting port. It contains the
following parts.
To use the cable tie set:
1. Firmly plug a cable to a correct port on the
projector. Insert the cable tie head to the
cable tie hole right above the connecting port.
Note that the cable tie cannot be removed
from the hole once it is inserted.
3. Insert the end of the cable tie to the cable tie
ratchet as illustrated.
4. Close the cable tie ratchet by pressing its tab.
2. Take the cable tie ratchet. Slightly open the
ratchet to surround the connecting cable.
5. Move the cable tie ratchet along with the
cable tie to the end of the cable plug.
The cable tie installation is done.
Cable tie
Cable tie ratchet
Cable tie head
1
3
4
2
5

11
English
RS232 command
RS232 pin assignment
No. Serial No. Serial
1NC 6NC
2RX 7RTSZ
3TX 8CTSZ
4NC 9NC
5GND
Function Ty p e Operation ASCII
Power
Write Power On <CR>*pow=on#<CR>
Write Power Off <CR>*pow=off#<CR>
Read Power status <CR>*pow=?#<CR>
Source Selection
Write COMPUTER/YpbPr <CR>*sour=RGB#<CR>
Write HDMI <CR>*sour=hdmi#<CR>
Write HDMI 2 <CR>*sour=hdmi2#<CR>
Read Current source <CR>*sour=?#<CR>
Picture Mode
Write Bright <CR>*appmod=bright#<CR>
Write Cinema <CR>*appmod=cine#<CR>
Write Standard/Vivid <CR>*appmod=std#<CR>
Write THX <CR>*appmod=thx#<CR>
Write Silence <CR>*appmod=silence#<CR>
Write User1 <CR>*appmod=user1#<CR>
Write User2 <CR>*appmod=user2#<CR>
Write ISF Night <CR>*appmod=isfnight#<CR>
Write ISF Day <CR>*appmod=isfday#<CR>
Write 3D <CR>*appmod=threed#<CR>
Read Picture Mode <CR>*appmod=?#<CR>
Picture Settings
Write Contrast + <CR>*con=+#<CR>
Write Contrast - <CR>*con=-#<CR>
Read Contrast value <CR>*con=?#<CR>
Write Brightness + <CR>*bri=+#<CR>
Write Brightness - <CR>*bri=-#<CR>
Read Brightness value <CR>*bri=?#<CR>
Write Color + <CR>*color=+#<CR>
Write Color - <CR>*color=-#<CR>
Read Color value <CR>*color=?#<CR>
Write Tint + <CR>*tint=+#<CR>
Write Tint - <CR>*tint=-#<CR>
Read Tint value <CR>*tint=?#<CR>
Write Sharpness + <CR>*sharp=+#<CR>
Write Sharpness - <CR>*sharp=-#<CR>
Read Sharpness value <CR>*sharp=?#<CR>
Write Flesh Tone + <CR>*fleshtone=+#<CR>
Write Flesh Tone - <CR>*fleshtone=-#<CR>
Read Flesh Tone value <CR>*fleshtone=?#<CR>
Write Color Temperature-Warm <CR>*ct=warm#<CR>
Write Color Temperature-Normal <CR>*ct=normal#<CR>
Write Color Temperature-Cool <CR>*ct=cool#<CR>
Write Color Temperature-Lamp native <CR>*ct=native#<CR>
Read Color Temperature status <CR>*ct=?#<CR>
Write Aspect 4:3 <CR>*asp=4:3#<CR>
Write Aspect 16:9 <CR>*asp=16:9#<CR>
Write Aspect Auto <CR>*asp=AUTO#<CR>
12345
6789

12
English
Function Ty p e Operation ASCII
Picture Settings
(Continued)
Write Aspect Real <CR>*asp=REAL#<CR>
Write Aspect Anamorphic <CR>*asp=ANAM#<CR>
Write Aspect Anamorphic 2.4:1 <CR>*asp=ANAM2.4:1#<CR>
Write Aspect Anamorphic 16:9 <CR>*asp=ANAM16:9#<CR>
Read Aspect status <CR>*asp=?#<CR>
Write Overscan Adjustment + <CR>*overscan=+#<CR>
Write Overscan Adjustment - <CR>*overscan=-#<CR>
Read Overscan Adjustment value <CR>*overscan=?#<CR>
Write Auto <CR>*auto#<CR>
Write Noise Reduction + <CR>*NR=+#<CR>
Write Noise Reduction - <CR>*NR=-#<CR>
Read Noise Reduction vaule <CR>*NR=?#<CR>
Write Red Gain + <CR>*RGain=+#<CR>
Write Red Gain - <CR>*RGain=-#<CR>
Read Red Gain value <CR>*RGain=?#<CR>
Write Green Gain + <CR>*GGain=+#<CR>
Write Green Gain - <CR>*GGain=-#<CR>
Read Green Gain value <CR>*GGain=?#<CR>
Write Blue Gain + <CR>*BGain=+#<CR>
Write Blue Gain - <CR>*BGain=-#<CR>
Read Blue Gain value <CR>*BGain=?#<CR>
Write Red Offset + <CR>*ROffset=+#<CR>
Write Red Offset - <CR>*ROffset=-#<CR>
Read Red Offset value <CR>*ROffset=?#<CR>
Write Green Offset + <CR>*GOffset=+#<CR>
Write Green Offset - <CR>*GOffset=-#<CR>
Read Green Offset value <CR>*GOffset=?#<CR>
Write Blue Offset + <CR>*BOffset=+#<CR>
Write Blue Offset - <CR>*BOffset=-#<CR>
Read Blue Offset value <CR>*BOffset=?#<CR>
Write Gamma Selection-1.8 <CR>*gamma=1.8#<CR>
Write Gamma Selection-2.0 <CR>*gamma=2.0#<CR>
Write Gamma Selection-2.1 <CR>*gamma=2.1#<CR>
Write Gamma Selection-2.2 <CR>*gamma=2.2#<CR>
Write Gamma Selection-2.3 <CR>*gamma=2.3#<CR>
Write Gamma Selection-2.4 <CR>*gamma=2.4#<CR>
Write Gamma Selection-2.6 <CR>*gamma=2.6#<CR>
Write Gamma Selection-2.8 <CR>*gamma=2.8#<CR>
Write Gamma Selection-BenQ <CR>*gamma=benq#<CR>
Read Gamma Selection status <CR>*gamma=?#<CR>
Write Brilliant color on <CR>*BC=on#<CR>
Write Brilliant color off <CR>*BC=off#<CR>
Read Brilliant color status <CR>*BC=?#<CR>
Write HDMI Format -Auto <CR>*HDMI=auto#<CR>
Write HDMI Format -PC Signal <CR>*HDMI=pc#<CR>
Write HDMI Format -Video Signal <CR>*HDMI=video#<CR>
Read HDMI Format status <CR>*HDMI=?#<CR>
Write CEC on <CR>*cec=on#<CR>
Write CEC off <CR>*cec=off#<CR>
Read CEC status <CR>*cec=?#<CR>

13
English
Function Ty p e Operation ASCII
Operation Settings
Write Splash Screen-BenQ <CR>*splash=benq#<CR>
Write Splash Screen-Black <CR>*splash=black#<CR>
Write Splash Screen-Blue <CR>*splash=blue#<CR>
Write Splash Screen status <CR>*splash=?#<CR>
Write Background Color-Black <CR>*background=black#<CR>
Write Background Color-Blue <CR>*background=blue#<CR>
Write Background Color-Purple <CR>*background=purple#<CR>
Read Background Color status <CR>*background=?#<CR>
Write Projector Position-Front Table <CR>*pp=FT#<CR>
Write Projector Position-Rear Table <CR>*pp=RE#<CR>
Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR>
Write Projector Position-Front Ceiling <CR>*pp=FC#<CR>
Read Projector Position status <CR>*pp=?#<CR>
Write Quick auto search/Auto source search <CR>*QAS=on#<CR>
Write Quick auto search/Auto source search <CR>*QAS=off#<CR>
Read Quick auto search status/Auto source
search status <CR>*QAS=?#<CR>
Write Menu Display Time -Always On <CR>*menutime=on#<CR>
Write Menu Display Time -5 sec <CR>*menutime=5s#<CR>
Write Menu Display Time -10 sec <CR>*menutime=10s#<CR>
Write Menu Display Time -15 sec <CR>*menutime=15s#<CR>
Write Menu Display Time -20 sec <CR>*menutime=20s#<CR>
Write Menu Display Time -25 sec <CR>*menutime=25s#<CR>
Write Menu Display Time -30 sec <CR>*menutime=30s#<CR>
Read Menu Display Time status <CR>*menutime=?#<CR>
Write Menu Position-Center <CR>*menuposition=center#<CR>
Write Menu Position-Top-Left <CR>*menuposition=tl#<CR>
Write Menu Position - Top-Right <CR>*menuposition=tr#<CR>
Write Menu Position-Bottom-Right <CR>*menuposition=br#<CR>
Write Menu Position-Bottom-Left <CR>*menuposition=bl#<CR>
Read Menu Positions status <CR>*menuposition=?#<CR>
Write Reminder Message - On <CR>*reminder=on#<CR>
Write Reminder Message - Off <CR>*reminder=off#<CR>
Read Reminder Message status <CR>*reminder=?#<CR>
Write Direct Power On-on <CR>*directpower=on#<CR>
Write Direct Power On-off <CR>*directpower=off#<CR>
Read Direct Power On-status <CR>*directpower=?#<CR>
Write Standby Settings-Network on <CR>*standbynet=on#<CR>
Write Standby Settings-Network off <CR>*standbynet=off#<CR>
Read Standby Settings-Network status <CR>*standbynet=?#<CR>
Lamp Control
Read Lamp Hour <CR>*ltim=?#<CR>
Write Normal mode <CR>*lampm=lnor#<CR>
Write Eco mode <CR>*lampm=eco#<CR>
Write Smart Eco mode <CR>*lampm=seco#<CR>
Read Lamp Mode status <CR>*lampm=?#<CR>

14
English
Function Ty p e Operation ASCII
Miscellaneous
Read Model Name <CR>*modelname=?#<CR>
Write Blank On <CR>*blank=on#<CR>
Write Blank Off <CR>*blank=off#<CR>
Read Blank status <CR>*blank=?#<CR>
Write Menu On <CR>*menu=on#<CR>
Write Menu Off <CR>*menu=off#<CR>
Write Up <CR>*up#<CR>
Write Down <CR>*down#<CR>
Write Right <CR>*right#<CR>
Write Left <CR>*left#<CR>
Write Enter/OK <CR>*enter#<CR>
Write BACK <CR>*back#<CR>
Write 3D Auto <CR>*3d=auto#<CR>
Write 3D Sync Off <CR>*3d=off#<CR>
Write 3D Sync Frame Sequential <CR>*3d=fs#<CR>
Write 3D inverter disable <CR>*3d=da#<CR>
Write 3D inverter <CR>*3d=iv#<CR>
Read 3D Sync status <CR>*3d=?#<CR>
Write Language + <CR>*lang=+#<CR>
Write Language - <CR>*lang=-#<CR>
Read Language status <CR>*lang=?#<CR>
Write Auto Power off -disable <CR>*APOFF=DIS#<CR>
Write Auto Power off - 5 min <CR>*APOFF=5#<CR>
Write Auto Power off - 10 min <CR>*APOFF=10#<CR>
Write Auto Power off - 15 min <CR>*APOFF=15#<CR>
Write Auto Power off - 20 min <CR>*APOFF=20#<CR>
Write Auto Power off - 25 min <CR>*APOFF=25#<CR>
Write Auto Power off - 30 min <CR>*APOFF=30#<CR>
Read Auto Power off status <CR>*APOFF=?#<CR>
Write AMX Device Discovery-on <CR>*amxdd=on#<CR>
Write AMX Device Discovery-off <CR>*amxdd=off#<CR>
Read AMX Device Discovery status <CR>*amxdd=?#<CR>
Read MAC Address <CR>*macaddr=?#<CR>
Write Quick Cooling on <CR>*QCooling=on#<CR>
Write Quick Cooling off <CR>*QCooling=off#<CR>
Read Quick Cooling status <CR>*QCooling=?#<CR>
Write High Altitude mode on <CR>*Highaltitude=on#<CR>
Write High Altitude mode off <CR>*Highaltitude=off#<CR>
Read High Altitude mode status <CR>*Highaltitude=?#<CR>
Write Key Lock on <CR>*keylock=on#<CR>
Write Key Lock off <CR>*keylock=off#<CR>
Read Key Lock status <CR>*keylock=?#<CR>
Write LED indicator on <CR>*led=on#<CR>
Write LED indicator off <CR>*led=off#<CR>
Read LED indicator status <CR>*led=?#<CR>

15
繁體中文
目錄
重要安全說明 ........................................................................................................................ 16
產品資訊 ...............................................................................................................................18
包裝盒內容 ...............................................................................................................................................18
規格 .............................................................................................................................................................18
投影機尺寸 ...............................................................................................................................................19
端子 .............................................................................................................................................................19
遙控器 ........................................................................................................................................................ 20
安裝 ....................................................................................................................................... 21
投影尺寸 ....................................................................................................................................................21
投影鏡頭偏移........................................................................................................................................... 22
天花板安裝圖........................................................................................................................................... 23
使用訊號線束組 ...................................................................................................................................... 24
RS232 指令 ........................................................................................................................... 25
RS232 針腳分配 .......................................................................................................................................25

16
繁體中文
重要安全說明
本投影機經設計完成及測試通過，符合資訊科技設備的最新安全標準。然而，為確保您安全地
使用本產品，請務必遵循本使用手冊 /安裝指南的指示與產品本身所標示的指示。
1. 操作投影機之前，請先閱讀本使用手冊 /安裝指南。請妥善保存本手冊，以供日後參考。
2. 操作時請勿直視投影機鏡頭。強光可能會造成您的視力受損。
3. 有關維修問題，請洽詢合格的維修人員。
4. 投影機的光源亮起時，請務必打開或移除鏡頭蓋 （如果有的話）。
5. 操作期間光源會變得很燙。
6. 有些國家的電壓不穩定。本投影機所設計安全操作的電壓區間為 100 至240 伏特交流電，但
如果發生斷電或功率驟然起伏達 ±10 伏特就會發生故障。如果在主電壓可能會波動或中斷的
區域使用本投影機，建議您經由穩壓器、雷擊突波保護器或不斷電系統 (UPS) 連接電源。
7. 當投影機在運作中，請勿讓任何物品擋住投影的鏡頭，因為這樣可能會使得該物品遇熱變形
甚至造成火災。若要暫時關閉光源，請使用空白功能。
8. 請勿使用超過額定壽命的光源。
9. 投影機插頭如果尚未拔下，請勿更換燈泡或任何電子零件。
10. 請勿將投影機放置在不平穩的手推車、架子或桌子上。否則投影機可能會掉落，造成嚴重損
壞。
11. 請勿打開投影機的機殼。機身內含有危險的高電壓配件，萬一接觸人體時可能會造成電擊
死亡。
請勿在任何狀況下打開或移除其它部分的護蓋。有關維修問題，請洽詢合格專業的維修
人員。
12. 請勿阻塞通風口。
- 請勿將投影機放置於毯子、寢具或其它柔軟物品的表面上。
- 請勿用布或其它物品覆蓋投影機。
- 請勿將易燃物放在投影機附近。
如果通風口嚴重阻塞而使投影機內部過熱，可能會引起火災。
13. 操作時請將設備置於平坦、水平的表面。
- 如果左右傾斜超過 10 度、前後超過 15 度，請勿使用投影機。使用投影機時，如果將投影機擺放在不平坦的
位置上，可能會導致燈泡故障或損壞。
14. 請勿將投影機直立擺放。因投影機可能會不穩摔落，導致人身受傷或投影機損壞。
15. 請勿踩在投影機上，或在上面放置任何物品。這樣除可能導致投影機損壞外，還可能造成意
外及人身受傷。
16. 當使用投影機時，您也許會在通風口附近感覺到些微的熱風與氣味。此乃正常現象，並不是
產品有瑕疵。
17. 請勿將液體放在投影機附近或放在投影機上。液體如果濺到投影機內，可能導致投影機故
障。投影機如果不慎弄濕，請立即拔掉電源線，並聯絡 BenQ，安排投影機的維修事宜。
18. 投影機可安裝於天花板上，顯示反轉影像。
19. 本裝置必須接地。
20. 請勿將本投影機放置在下列任何環境中。
- 不通風或密閉場所。投影機離牆面至少要有 50 公分的距離，且周圍空氣要流通。
- 過熱場所。例如：車窗緊閉的車內。
- 潮濕、多塵或煙霧瀰漫的場所。因為可能會污染光學元件，縮短投影機的使用壽命，並使投影影像變暗。
- 靠近火災警報器的場所。

17
繁體中文
- 周圍溫度超過 40°C/104°F 的場所。
- 海拔超過 3000 公尺 （10000 英呎）的場所。
Hg - 燈泡內含水銀。請依據當地法規進行處理。詳細資訊，請參閱 www.lamprecycle.org。
冷卻注意事項
風險群組 2
1. 根據光源及光源系統的光生物安全分類，本產品屬於 IEC
62471-5:2015 的風險群組 2。
2. 本產品可能發出有害的光學輻射。
3. 請勿直視發光的光源，這樣可能對眼睛造成傷害。
4. 在有任何明亮的光源時，請勿直視光束。
通風 安裝注意
避免在不通風或密閉場所
使用。
為使投影機達到適當的通風效果，請務必如下圖所示使投影機
周圍保留一些空間：
• 桌面 • 桌面
• 天花板 • 堆疊
POWER
TEMP
LAMP
進氣口 出風口
50 公分
以上
70 公分
以上
50 公分
以上
50 公分
以上
30 公分
以上
50 公分
以上
至少 100 公釐

18
繁體中文
產品資訊
包裝盒內容
選購配件
規格
投影機 隨附電池的遙控器 訊號線束組 x 3
安裝指南 使用手冊光碟 保證書 *電源線
• 所提供的配件適用於購買所在地區，且可能會與手冊上的圖片有所不同。
• * 保證書僅於某些地區提供。詳情請詢問您的經銷商。
1. 備用燈泡組
2. 天花板吊掛工具組
3. RS232 訊號線
4. 歪像鏡頭
5. BenQ DGD5 3D 眼鏡
顯示系統 1-CHIP DMD
解析度 3840 x 2160 （使用 XPR）
2716 x 1528 （不使用 XPR）
光源 240 瓦燈泡
亮度 2200 流明
耗電量 384 瓦 （最大）；< 0.5 瓦 （待機）
重量 14.8 公斤 （32.6 磅）

19
繁體中文
投影機尺寸
470.7 公釐 （寬） x 224.9 公釐 （高） x 564.7 公釐 （深）
端子
• LAN (10/100M)
用來連接 RJ45 Cat5/Cat6 乙太網路訊號
線，以透過網路控制投影機。
• IR IN
專供紅外線增強線使用，確保更好的遙
控器訊號接收。
• PC
15 針VGA 埠，用於連接 RGB 或電腦。
• HDMI 1 （2.0 版）及其訊號線束孔
連接 HDMI (4K) 信號源。
連接訊號線束組。
• HDMI 2 （1.4a 版）及其訊號線束孔
連接 HDMI 信號源。
連接訊號線束組。
• USB MINI-B
僅適用於韌體升級。
• 12V TRIGGER 1/2
啟動外接裝置，例如電動布幕或光線控制等。
• RS232
標準 9 針D-sub 介面，用於連接電腦控制系統
及投影機維護使用。
POWER
TEMP
LAMP
470.7
564.7 224.9
單位：公釐