BenQ SP0005 User manual

SP0005 / SP0008 / SP0016
5/8/16-Port
Fast Ethernet Switch
User’s Guide

FCC Warning
This equipment has been tested and found to comply with the limits for Class
A & Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this user's guide, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
CE Mark Warning
This device complies with requirements of EN50081-1 and EN50082-1 under
the scope of EMC Directive EEC.
Trademarks
Copyright ©2002 Benq Corporation.
Contents subject to change without prior notice. Benq is a registered trade-
mark of Benq Corporation. All other trademarks belong to their respective
proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means
or used to make any derivative such as translation, transformation, or adapta-
tion without permission from Benq Corporation.

i
1. Introduction .............................................................................. 1
1.1. Product Overview .............................................................................. 1
1.2. Features & Specifications ................................................................... 2
1.2.1 Features ..................................................................................................... 2
1.2.2. Technical Specifications ......................................................................... 2
1.2.3. Physical Specifications ............................................................................ 3
1.3. Product outlook and terminology ................................................... 4
1.3.1. SP0005 ....................................................................................................... 4
1.3.2. SP0008 ....................................................................................................... 5
1.3.3. SP0016 ....................................................................................................... 6
1.3.4. Terminology ............................................................................................. 6
1.4. Package contents ................................................................................. 7
2. Installation ................................................................................. 8
2.1. Operating Environment ..................................................................... 8
2.2. Connecting to network devices ...................................................... 8
2.3. Connecting the power ....................................................................... 8
3. Trouble Shooting ..................................................................... 9

ii
1. 緒論 ..........................................................................................10
1.1. 產品簡介 ........................................ 10
1.2. 特性 &規格 ......................................................................................... 11
1.2.1 產品特性 ..................................................................................................11
1.2.2. 技術規格 .................................................................................................11
1.2.3. 外觀規格 .................................................................................................12
1.3. 產品外觀及術語 ................................................................................ 13
1.3.1. SP0005 ......................................................................................................13
1.3.2. SP0008 ......................................................................................................14
1.3.3. SP0016 ......................................................................................................15
1.3.4. 術語 ..........................................................................................................15
1.4. 產品包裝 ........................................ 16
2. 安裝 ...........................................................................................17
2.1. 工作環境 .............................................................................................. 17
2.2. 網絡連接 .............................................................................................. 17
2.3. 連接電源 ......................................... 17
3. 故障排除 ..................................................................................18

1. Introduction - 1
1. Introduction
1.1. Product Overview
This SP0005/SP0008/SP0016 high performance Fast Ethernet switch provides
five/eight/sixteen Fast Ethernet ports to segment network traffic, extend Fast
Ethernet connection distance, and convert data packets between different
transmission speeds. This Fast Ethernet Switch provides shielded RJ-45 ports
both with 10Base-T and 100Base-TX Auto-negotiation capability and MDI/
MDI-X auto crossover. All ports in this switch support Full-Duplex and Half-
Duplex operation modes. The Fast Ethernet Switch is typically used to seg-
ment network traffic that can improve the network performance by increas-
ing the total bandwidth as illustrated in Figure 1-1.
This Fast Ethernet Switch utilizes stored-and-forward switching architecture
that filters and forwards data after the complete data packet is received and
examined to be free of errors. With one set of status LEDs for each individ-
ual port, the switch operation status can be easily monitored. Their slim and
compact design allows direct placing on the desktop or conveniently
mounted on the wall or the side of a desk to accommodate cabling consider-
ation.
Figure 1-1
ADSL/Cable modem
Linux OS
Mac OS
Server
Windows Me/XP/NT
Windows 98/95/2000

1. Introduction - 2
1.2. Features & Specifications
1.2.1 Features
• Compliant with IEEE 802.3 10Base-T Ethernet and 802.3u 100Base-TX Fast
Ethernet Standards.
• Provides 5/8/16 ports for 10Base-T/100Base-TX, standard RJ-45 connectors.
• All RJ-45 ports supports 10Base-T/100Base-TX and Full-Duplex/Half-Duplex
Auto-negotiation function.
• Supports MDI/MDI-X auto crossover.
• Supports store-and-forward switching mechanism.
• Plug-and-Play
• Performs non-blocking full wire speed rate.
• Supports up to 4K/2K/8K (5/8/16 ports) MAC addresses table / hashing
algorithm on address learning.
• Supports Aging function and 802.3x flow control for full Duplex and
collision-based backpressure function for half duplex operation.
• 128K/128K/512K (5/8/16 ports) Bytes buffer memory.
• Automatic address learning, address aging and address migration.
• Simple and economical way to bridge 10Base-T network and 100Base-TX
network.
• Front panel status LEDs
• Desktop size.
• Wall mountable.
1.2.2. Technical Specifications
Ethernet Standards IEEE 802.3 10Base-T, 802.3u 100Base-TX
LED report
Power Steady Power On
Off Power Off
100 M
(Green)
Steady (LNK) A valid network connection established
Flashing (ACT) Transmitting or receiving data
10 M
(Yellow)
Steady (LNK) A valid network connection established
Flashing (ACT) Transmitting or receiving data
Cable 10Base-T: 2-pair UTP Cat. 3,4,5, up to 100m (328 ft)
100Base-TX: 2-pair UTP Cat. 5, up to 100m (328 ft)
Switching Method Store-and-forward
Forwarding Rate 14,880pps for 10Mbps; 148,800pps for 100Mbps

1. Introduction - 3
1.2.3. Physical Specifications
AC Input 50-60Hz, External power adapter
Operating Temperature 0°C

~ 50°C (32°F ~ 122°F )
Storage Temperature -20°C ~ 70°C (-4°F ~ 158°F )
Humidity 10% ~ 90% non-condensing
Emission Compliance
FCC part 15 Class B, CE Mark, VCCI Class B, C-TICK
for SP0005 & SP0008
FCC Class A, CE Mark, VCCI Class A, C-TICK
for SP0016
Safety UL/CSA
Dimension
162mm x 103mm x 32mm (SP0005)
162mm x 103mm x 32mm (SP0008)
301mm x 125mm x 32mm (SP0016)
Net Weight 250g (SP0005); 250g (SP0008); 540g (SP0016)

1. Introduction - 4
1.3. Product outlook and terminology
1.3.1. SP0005
Top View
Front View
Rear View
WIDTH * DEPTH * HEIGHT = 162*103*32 mm

1. Introduction - 5
1.3.2. SP0008
Top View
Front View
Rear View
WIDTH * DEPTH * HEIGHT = 162*103*32 mm

1. Introduction - 6
1.3.3. SP0016
1.3.4. Terminology
PWR:
This Green LED lights when the power adapter is mounted
LINK/ACT 10/100:
The Yellow LED lights when there is a valid 10-Base data linked on the port.
And Green LED lights for 100-Base data linked. LED lights blinking when
either 10-Base or 100-Base data is transmitted.
Top View
Front View
Rear View
WIDTH * DEPTH * HEIGHT = 301*125*32 mm

1. Introduction - 7
1.4. Package contents
The package should contain the following items:
SP0005/SP0008/SP0016 x 1
AC power adapter x 1
This User’s Guide
IF any item is found missing or damaged, please contact your local Benq
reseller for replacement.

2. Installation - 8
2. Installation
2.1. Operating Environment
This switch must be installed and operated within the limits of specified
operating temperature and humidity (see previous section under Specifica-
tions).
• Do not place objects on top of the unit.
• Do not obstruct any vents at the sides of the unit.
• Do not position the unit near any heating source such as heater, radiator,
or direct exposure to sun.
• Prevent entering of water and moisture into the unit.
• If necessary, use dehumidifier to reduce humidity.
• Always avoid dust and dirt.
• Allow some space between the product and the surroundings to facilitate
dissipation of heat generated inside the switch.
2.2. Connecting to network devices
The RJ-45 ports on the switch are designed as MDI/MDI-X auto crossover
ports which allow using straight-through cables to connect any port on this
switch to network device.
Connect one end of the network cable to the RJ-45 port on the rear panel,
and then connect the other end of the network cable to the RJ-45 port on
the network device. Follow the same procedure to connect all the RJ-45
ports of the switch. The UTP network cables must comply with EIA/TIA 568
specifications and Category 5 standard for 100Mbps data transmission and
Category 3, 4, 5 for 10Mbps connection. Maximum length, using UTP cable,
between the switch and connected device is 100 meters (328ft). Once the
network cable is connected to both ends and the attached network device is
powered on, the green LINK/ACT 10/100 LED should be lit (for 100-Base
data linked by auto-negotiation).
2.3. Connecting the power
Connect the output end of the power adapter to the power connector on
the rear panel of the unit. Connect the power adapter to the power outlet.
The green Power LED on the front panel should be lit.

3. Trouble Shooting - 9
3. Trouble Shooting
The SP0005/SP0008/SP0016 can be easily monitored by its LED indicators.
Please follow the troubleshooting steps below to solve any problem you may
encounter during installation or implementation of the SP0005/SP0008/
SP0016.
1. Power LED is not lit
Check if the power cord is properly connected to the external power
adapter and the power outlet. Make sure the DC power jack is firmly
plugged into the power socket of the switch.
2. 100M Link/Activity(Green) is not lit when connect to 100
Mbps device
• Check the power switch of the network device attached to the switch;
make sure it is turned ON.
• Check the network cable; make sure it is properly connected to the switch
and the network device.
• Check the network cable; make sure the UTP cables comply with EIA/TIA
568 and Category 5 specification.
Please perform the following tests
• Please check whether the RJ-45 cable is functional. Replace with another
working cable and see whether the condition can be improved.
• Use another port on the SP0005/SP0008/SP0016. If a link can be established
this way, the first port is faulty. Please contact your local Benq dealer for
assistant.
• Make sure that all devices are connected to the network.
• Please ensure that the network adapter cards installed in the workstation
or other devices to the switch are in well working condition.
[!] Contact your dealer if problem persists.

1. 緒論 - 10
1. 緒論
緒論緒論
緒論
1.1. 產品簡介
產品簡介產品簡介
產品簡介
SP0005/SP0008/SP0016 高性能快速以太網交換機具有 5/8/16 個快速以太
網端口，可將數據在不同速度的網絡之間進行交換並延長傳輸距離。每
端口均為具有 MDI/MDI-X 自適應及 10Base-T/100Base-TX 自適應的標準
RJ-45 接口。且均可自適應全雙工 /半雙工模式。主要用以增加網絡帶寬
來提高性能，如圖 1-1 所示。
SP0005/SP0008/SP0016 採用存儲─轉發機制，可對數據包進行校驗後，
再進行過濾及轉發，並且每個端口都具有獨立 LED 指示燈用以監視工作
狀態。緊湊的設計使得設備可以方便的放在桌面或者挂置於牆上及桌側
以方便電纜連接。
圖1-1
ADSL/Cable modem
Linux OS
Mac OS
Server
Windows Me/XP/NT
Windows 98/95/2000

1. 緒論 - 11
1.2. 特性
特性特性
特性 &規格
規格規格
規格
1.2.1 產品特性
產品特性產品特性
產品特性
• 遵從 IEEE 802.3 10Base-T 及802.3u 100Base-TX 快速以太網標準。
• 具有 5/8/16 個10Base-T/100Base-TX 標準 RJ-45 接口。
• 所有均支持 10Base-T/100Base-TX 及全雙工 /半雙工自適應。
• 支持 MDI/MDI-X 自適應。
• 存儲─轉發機制。
• 即插即用。
• 無阻塞全線速轉發。
• 具有最大 4K/2K/8K (5/8/16 ports) MAC 地址表 /地址散列運算自學習
功能。
• 支持 Aging 功能與 802.3x 全雙工流控制及半雙工背壓流控制。
• 128K/128K/512K (5/8/16 ports) 緩存。
• 地址自學習，自釋放及地址漫游功能。
• 10Base-T 及100Base-TX 網絡間簡單經濟的連接方式。
• 前面板狀態指示燈。
• 同桌面大小。
• 可壁挂設計。
1.2.2. 技術規格
技術規格技術規格
技術規格
以太網標準 IEEE 802.3 10Base-T, 802.3u 100Base-TX
LED 指示燈
設備 電源指示
100 M
(綠色 )
亮燈 連接狀態
閃爍 工作狀態
10 M
(黃色 )
亮燈 連接狀態
閃爍 工作狀態
電纜 10Base-T: 2 對3, 4, 5 類非屏蔽雙絞線
100Base-TX: 2 對5類雙絞線
交換機制 存儲─轉發
轉發速率 14,880pps for 10Mbps; 148,800pps for 100Mbps

1. 緒論 - 12
1.2.3. 外觀規格
電源 50-60Hz 外置電源適配器
工作溫度 0°C ~ 50°C (32°F ~122°F)
存放溫度 -20°C~ 70°C (-4°F ~ 158°F)
工作濕度 10% ~ 90% 非冷凝
輻射標準
FCC part 15 Class B, CE Mark, VCCI Class B, C-TICK
for SP0005 & SP0008
FCC Class A, CE Mark, VCCI Class A, C-TICK
for SP0016
安全標準 UL/CSA
外部尺寸
162mm x 103mm x 32mm (SP0005)
162mm x 103mm x 32mm (SP0008)
301mm x 125mm x 32mm (SP0016)
淨重 250g (SP0005); 250g (SP0008); 540g (SP0016)

1. 緒論 - 13
1.3. 產品外觀及術語
產品外觀及術語產品外觀及術語
產品外觀及術語
1.3.1. SP0005
上視圖
上視圖上視圖
上視圖
前視圖
前視圖前視圖
前視圖
後視圖
後視圖後視圖
後視圖
長* 寬* 高= 162*103*32 mm

1. 緒論 - 14
1.3.2. SP0008
上視圖
上視圖上視圖
上視圖
前視圖
前視圖前視圖
前視圖
後視圖
後視圖後視圖
後視圖
長* 寬* 高= 162*103*32 mm

1. 緒論 - 15
1.3.3. SP0016
1.3.4. 術語
術語術語
術語
PWR:
接通電源後，綠燈點亮。
連接 / 工作 10/100:
連接 10 兆網絡時，黃燈點亮。
連接 100 兆網絡時，綠燈點亮。
數據傳輸時，黃燈或綠燈均會閃爍。
上視圖
上視圖上視圖
上視圖
前視圖
前視圖前視圖
前視圖
後視圖
後視圖後視圖
後視圖
長* 寬* 高= 301*125*32 mm

1. 緒論 - 16
1.4. 產品包裝
產品包裝產品包裝
產品包裝
包裝中應包括如下部件：
SP0005/SP0008/SP0016 x 1
交流電源適配器 x 1
本用戶手冊
如有任何部件缺失或損壞，請與本地 Benq 經銷商聯繫調換。