Beny Sports V-FIT-ST Herculean LFG2 User manual

AB3098-UK
Herculean LFG2 Home Gym

General Information
Quality
This exercise product has been designed and
manufactured to comply with the latest (BS EN 957)
British and European Safety Standards.
Questions
Should you encounter any difficulty with the assembly,
operation or use of your V-fit exercise product or if you
think that you may have parts missing, please DO NOT
return it to your retailer but contact us first for help and
advice, asking for CUSTOMER SUPPORT, by any of the
following means.
Queries
If you do have any queries, please ensure that you have
the following information ready for our Customer Support
Staff:
YOUR NAME
YOUR ADDRESS
YOUR PHONE NUMBER
PRODUCT MAKE OR BRAND
PRODUCT MODEL
PRODUCT SERIAL NUMBER
DATE OF PURCHASE
NAME OF RETAILER
PART NUMBERS REQUIRED
Guarantee
Beny Sports Co. UK Ltd. guarantee's its product range for
DOMESTIC USE ONLY for a period of 1 YEAR from the
original certified date of purchase. During this period we
have the right to: -
a). Provide parts for the purchaser to effect repair.
b). Repair the product, returned to our warehouse
(at the purchaser's cost).
c). Replace the product if it is deemed (by us) to be
economical to do so.
This guarantee does not cover wear and tear on
upholstery or consumables.
This guarantee does not cover abuse, defects caused by
storage or use outside those intended.
If you need to advise us of a defect with your product and
in order for us to service any requirement for replacement
parts or repairs, we will ask for proof of purchase. Failure
to do so will result in any claim for replacement parts or
repairs being refused.
This guarantee, (both given and implied) applies to the
original purchaser only, is not transferable and will be
invalidated if used outside of the above criteria.
This guarantee is valid only in the United Kingdom and Eire.
This does not affect your statutory rights as a consumer.
Customer Support
Page 4
Tel:- 0800 3 101 202 or
[phone]
Email:- [email protected]
Website: www.benysports.co.uk
CUSTOMER SUPPORT open from 9.00am to 5.00pm
from Monday to Friday
Beny Sports Co. UK Ltd.
Unit 8 Riparian Way,
The Crossings Business Park,
Cross Hills,
West Yorkshire.
BD20 7BW
Tel:- 0800 3 101 202 or
[phone]
Email:- [email protected]
Website: www.benysports.co.uk
CUSTOMER SUPPORT open from 9.00am to 5.00pm
from Monday to Friday
Beny Sports Co. UK Ltd.
Unit 8 Riparian Way,
The Crossings Business Park,
Cross Hills,
West Yorkshire.
BD20 7BW

Assembly
21
41
60
62 22
28
38
20 35
01
43 18
46
58
59
16
Stage A.
1). Lay the Rear Stabiliser (20) flat on the floor and lay the Base Frame U Bracket (22) onto the centre of the Rear Stabiliser,
making sure the loop is facing the rear of the gym. Place the 2 Weight Guide Tubes (21) into the 2 outer holes in the U Bracket.
2). Connect the Main Base (1) and the Rear Stabiliser together using 2 x M10 x 60mm Hex Bolts (28), 4 x M10 Flat Washers
(38) and 2 x M10 Nylon Locknuts (35).
3). Lay the Footplate (18) onto the front of the Main Base and lock in position with the Footplate Lock Pin (43).
4). Slide the 2 Rubber Bumpers (62) onto the Weight Guide Tubes followed by the 6 Weight Plates (60).
5). Take the Selector Shaft (16) and fit the Selector Shaft Bush (58) and Selector Shaft Pin (46) as per inset "A". Slide the Top
Plate (59) onto the Weight Guid Tubes and locate the Selector Shaft in position, setting the Top Plate onto the top Weight
Plate. Use the Weight Selector Pin (41) to select the desire weight.
Tip: To lock the weight stack simply place the Weight Selector Pin (41) into the welded bracket on the top of the Base
Frame U Bracket (22) which will lock the Selector Shaft (16).
Please note that as part of our production checking and for your convenience, all tube caps where necessary have been
fitted in the pre-packing stage.
Carefully unpack each component, checking against the parts list that
you have all the necessary parts to complete the assembly of your gym.
Please note that some of the parts may be pre-fitted to major
components, so please check carefully before contacting our
CUSTOMER SUPPORT team.
In any event, please do not return the product to your retailer before
contacting us first.
Tel:- 0800 3 101 202 or
[phone]
Email:- [email protected]
CUSTOMER SUPPORT is open from 9.00am to 5.00pm from Monday to Friday
e
Do NOT FULLY TIGHTEN any
Bolts, Nuts or Fittings at this
stage unless specifically
instructed to do so.
Note
X
Please ensure when finally tightening
all Bolts that the locking ring in the
Locknut is fully engaged as (2) below.
(2)
(1)
Beny Sports Co. UK Ltd.
Unit 8 Riparian Way,
The Crossings Business Park,
Cross Hills,
West Yorkshire.
BD20 7BW
Page 13

Beny Sports Co. UK Ltd.
Unit 8 Riparian Way,
The Crossings Business Park,
Cross Hills,
West Yorkshire
BD20 7BW
CUSTOMER SUPPORT
Open from 9.00am to 5.00pm from Monday to Friday
Tel: FREEPHONE (in the UK) 0800 3 101 202
or
[phone] (outside the UK)
E-mail: [email protected]
Website: www.benysports.co.uk
© Copyright BSCL - 2021