Berkley Jensen 235412 User manual

1/ 31
8’ x 8’
HARDTOP GAZEBO
ARTICLE# 235412
ASSEMBLY INSTRUCTION
Note: The gazebo needs to be installed in cooperation with four people.
The following tools are not included and needed for assembly:
If you have comments or questions, please contact BJ’s Wholesale Club at 1-800-934-1204.
If you have any issues with the product, do not return the product back to the store.
For any questions, replacement parts or issues about our product, call Sunjoy
Customer Service 1(866) 578 6569. For further assistance, please email us at
[email protected].
Pistol Drill Tape Measure Hammer Screwdriver Ladder 5 people

2/ 31
Warning! To reduce the risk of serious injury, read the following safety instructions before assembling
and using the gazebo.
Caution! Always keep children under close supervision while they are using or around this product.
Never leave children unattended.
This product is intended for outdoor use only.
The product should be assembled on a flat stable surface.
Do not assemble the gazebo on unstable surfaces.
Ensure the location and clearance of your gazebo is acceptable.
The gazebo must be anchored with stakes into the ground for added safety. It is recommended that
it should not be permanently attached to a concrete floor or platform.
Arrange the necessary manpower when assembling or moving the product.
Some parts may contain sharp edges. Wear protective gloves and glasses if necessary.
Keep children and pets away while setting up the gazebo.
Check all nuts and bolts periodically for tightness. When required, tighten them again.
Repairing and replacing parts should be done by a qualified technician.
The gazebo is intended for decorative and shade purposes only, and is not designed to withstand
harsh weather, including high winds, rain and snow.
If the product is not being used for long periods of time (e.g. winter), it should be stored in a clean,
dry environment.
Do not put a Liquid Propane or Wood Burning fire pit or fireplace inside the product.
Do not climb or place heavy objects onto the gazebo roof.
Retain the original packaging to store and protect the gazebo during the winter months.
Do not use or enter the gazebo if the following conditions exists：
1. Visible movement of supports, roofing panels or a sagging roof.
2. Unusual noise from the gazebo.
3. Deformed roof panels.
4. Damaged or missing bolts/fasteners.
Please check your HOA, Local, and State Governments prior to purchasing and assembling
gazebos. These local organizations may require permits and specific requirements for installation.
Maintain your instruction manual for future reference
Warranty: Please retain you receipt for proof of purchase.
I
mportant Safety Instructions

3/ 31
EXPLODED DRAWING

4/ 31
Parts List
Label Part Number Description Qty Part Image
08 P000200227 Post 4
10 P005000200 Arc Support 1 4
11 P005000201 Arc Support 2 4
25 P000400957 Outer Left Beam 4
26 P000400958 Outer Right Beam 4
27 P000400959 Inner Long Beam 4
21 P000400960
Inner Short Beam
1 (Long) 4
06 P000400512
Inner Short Beam
2 (Short) 4
09 P006100087 Base Cover 16
C5 P000100224 Base 4
H2 P000500930 Slanting Beam
Connector 4
I2
P000500931
Middle Beam
Connector 4
P2 P000601155
Big Roof Slanting
Beam 4
B6 P000601156
Big Roof Middle
Beam 4
A1 P000500929
Big Roof Frame
Connector 2
B2 P000500928
Big Roof Frame
Short Tube 2
W7 P000601157
Big Roof Long
Small Beam 8

5/ 31
W6 P000601158
Big Roof Short
Small Beam 8
S3a P005700338
Mosquito Netting
Pipe 1 4
S3b P005700339
Mosquito Netting
Pipe 2 4
I5
P000700511
Big Roof Up
Cover Panel 4
I6
P000700510
Big Roof Lower
Left Cover Panel 4
I7
P000700509
Big Roof Lower
Right Cover
Panel
4
N4 P000800210
Big Roof Slanting
Beam Cover 4
O4 P000800211
Big Roof Middle
Beam Cover 4
D P000500927
Small Roof
Connector 1
C1 P000601154
Small Roof
Slanting Beam 4
F1 P000700508
Small Roof
Panel 4
H1 P000800209
Small Roof
Slanting Beam
Cover
4
I
P000900080 Small Roof Top
Cover 1
P P005800001 Hook 1

6/ 31
Hardware Pack
Label Part Number Description Qty Add Part Image
AA H010010276 Bolt M10*205 8 1
BB H050030001 Flat Washer
M6 161 9
CC H030050037 Screw M5*35 104 6
DD H040010004 Nut M6 12 1
EE H030050036 Screw M5*25 64 4
FF H010020011 Bolt M6*15 112 6
GG H010020016 Bolt M6* 45 16 1
HH H010030083 Bolt M8*35 16 1
II H030030010 Bolt M8*35 16 1
JJ H010020009 Bolt M6*55 12 1
KK H010030084 Bolt M8*25 24 2
LL H040050020 Non-slip Nuts
M10 8 1
MM H050030002 Flat Washer
M8 56 3

7/ 31
NN H050030003 Flat Washer
M10 24 2
OO H030010031 Screw
M10*80 8 1
PP H070010003 Stake Φ8*180 8 0
QQ H010020013 Bolt M6*35 8 1
RR H090990002 M3 Drill 2 0
SS H040090005 Nut M8*20 16 1
VV H040090004 Nut M8*8 24 2
WW H040040001 M6 Nut 1 1
Z1 H090010017 Wrench M6 2 0
Z2 H090030005 Allen Key M8 1 0
Z4 H090010015 Wrench M10 2 0

8/ 31
1
4X
16X
4X

9/ 31
4X
4X
16X
16X
16X
4X
16X
4X
2

10 / 31
8X
8X
4X
4X
8X
4X
3

11 / 31
4
40X

12 / 31
16X
4X
10
5
Locating hole

13 / 31
4X
12X
4X
4X
6

14 / 31
4X
4X
32X
12X
4X
4X
7

15 / 31
d1=d2
16X
16X
32X
4X
4X
Rt
∠
90
Assembly Tip on Step 8:
Please measure to make sure the length of d1 is equal to d2
before moving to next step to ensure a square frame and best
results. Keep the beam at right angles to the post, the post
at right angles to the ground, and keep the beam horizontal.
8

16 / 31
9
2X
2X
4X
4X

17 / 31
10
4X
16X
16X

18 / 31
11
4X
8X
8X
24X
8X

19 / 31
12
4X
1X
1X
4X
8X
4X

20 / 31
13
4X
4X
1X