Broyhill Biltmore SC-K-454PGSND User manual

1
PATIO FUTON SWING
BILTMORE
ASSEMBLY INSTRUCTION
ITEM#: SC-K-454PGSND
SKU#: 810453870
Need help? We are here for you!
Please contact 1-800-457-4652 or contact us at
www.numarkcustomerservice.com for assistance

WARNINGS
CLEANING AND MAINTENANCE
2
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM CANOPY FABRIC
The canopy is made with flame-resistant fabric which meets CPAI-84 specifications. It is not
fireproof. The canopy fabric will burn if left in continuous contact with flame source. The application
of any foreign substance to the canopy fabric may render the flame-resistant properties ineffective.
* Determine you have adequate space for assembly (1.83m or 6ft.) from any obstruction, including
buildings, tree limbs, and electrical wires.
* Assembly by four adults is recommended
* Keep children away during assembly. This item contains small parts which can be swallowed by
children. Children should always be under adult supervision while using this product.
* Always inspect the swing during each use for any obstructions.
* Remove the canopy in heavy wind conditions to avoid tipping over and damage to the swing.
* Do not discard any of the packaging until you have checked that you have all the parts and fittings.
* Retain the assembly instructions for future reference.
* The manufacturer will not accept responsibility for unauthorized repairs or modifications to
this product.
* Weight limit is 750lbs.
* This product is for residential use only, not for commercial use.
CAUTION:BEFORE YOU BEGIN ASSEMBLY
* Annually:
* Check all nuts and bolts for tightness each season and more often if used frequently.
* Oil all metal moving parts with a general purpose lubricating oil to ensure proper performance
and safety.
* To clean, wash frame and fabric with mild soap and water; rinse thoroughly. Dry frame completely
and allow the fabric to drip dry away from direct sunlight.
* Do not use bleach, acid, or other solvents on the fabric or frame parts.
* To prolong the life of your swing we recommend storage in a dry area when not in use or during
austere weather conditions.

Sa (8 + 1 spare )
M6 x 12L Bolt
Sb (12 + 1 spare )
M6 x 18L Bolt
Sl (2)
Hook
Sk (2)
Plastic Washer
Sc (2)
M6 x 55L Bolt
Sd (16 + 1 spare )
M8 x 15L Bolt
Se (16 + 1 spare )
M8 x 20L Bolt
Sj (2)
Nut
Si (42)
Large Metal Washer
Sf (8 + 1 spare)
M8 x 45L Bolt
Sh (14)
Sp (1)
Hex Wrench
Sn (1)
Open Hex Wrench
So (1)
Allen Wrench
Small Metal Washer
Sg (2)
M8 x 77L Bolt
Sm (16)
Lawn Stake
Sr (14)
Small Locker Washer
Ss (40)
Large Locker Washer
Pre-Assembly
Planning Assembly
To prevent damage, place all parts on a soft, non-abrasive surface during assembly.
• Identify all parts
• Read through all instructions before beginning assembly
Hardware Included
Note: Hardware not shown to Actual size.
Please contact 1-800-457-4652 or contact us at www.numarkcustomerservice.com for assistance
3

A Leg Post 4
B Side Panel
C Top Crossbar
D Top Crossbar
E Top Crossbar
F1 Inside Canopy Crossbar
F2 Outside Canopy Crossbar
G Leg Support Bar
H Left Arm
I Right Arm
J Rear and Front Connector Bar
K Seat and Back
L Long Hanging Bar
M Short Hanging Bar
N Canopy
O Canopy Side Bar
P Cushion
Q Post Base
R Base Plate
ITEM DESCRIPTION QUANTITY
2
2
2
2
3
2
1
1
1
2
1
4
2
1
2
1
4
4
A
B
C
D
E
G
H
I J
K
L
M
N
O
P
Q
R
Sl
Sm
F1 F2
Pre-Assembly (continued)
Package Contents
4
1
Sa x 8
M6 x 12L Bolt
Note: The side with sunk hole on the base plate should be towards outside and keep the base plate and bolts level.
Securely tighten all bolts. Repeat procedure for the other remaining three leg posts.
A
A
Q
R
Sa Sa
Assembly Note: The Broyhill Logo located on one of the
Base Plates should be positioned on the front
left post as you face the swing.
Attaching the Leg Post to the Post Plate and Base Plate

2
Se x 16
M8 x 20L Bolt
Si x 16
Large Metal Washer
Do not tighten completely.
Repeat procedure for the other side and the other pair of leg posts.
Se
A
A
Ss
B
Si
Ss x 16
Large Locker Washer
5
3
Do not tighten completely.
Repeat procedure for the other pair of top crossbars.
Sb x 8
M6 x 18L Bolt
Sh x 8
Small Metal Washer
C
D
C
D
Sb
Sb
Sh
Sh
D
C
Sr
Sr
Sr x 8
Small Locker Washer
Sd x 16
M8 x 15L Bolt
4
A
D
C
A
D
C
AA
Sd
Sd
A
D
Ss
Ss
Si
Si
Ss x 16
Large Locker Washer
Si x 16
Large Metal Washer
Do not tighten completely.
Repeat procedure for the other three sides.
5
Note: The side with iron end should be towards down.
Do not tighten completely.
Repeat procedure for the other top crossbar.
Si x 8
Large Metal Washer
Sf x 8
M8 x 45L Bolt
E
C
C
E
D
D
Sf
Si
Ss
Ss x 8
Large Locker Washer
Attaching the Side Panel to the Leg Post
Assemble Top Crossbars
Attach Top Crossbar to Leg Post
Assemble Top Crossbars to Top Crossbars
Assembly

6
6
7
Sh x 4
Small Metal Washer
Sb x 4
M6 x 18L Bolt
Do not tighten completely.
Repeat procedure for the other side canopy crossbar.
F1
F1 F1
C
D
D
C
F1
C
F1
C
F2
C
F2
F2
C
D
C
D
F2
C
Sb
Sh
Sr
Sr x 4
Small Locker Washer
Assembly
Insert Inside Canopy Crossbar into Top Crossbar
Insert both ends of the inside canopy crossbar into top
crossbar at the same time.
Repeat procedure for the other two inside canopy crossbars.
Insert Outside Canopy Crossbar into Top Crossbar
8
Note: The side with “ inside ” label and “U ” shaped
bracket should be towards inside.
The side with the connected bracket out should be facing upwards.
TIGHTEN ALL BOLTS FOR STEPS 2, 3, 4, 5, 7,8.
Sc x 2
M6 x 55L Bolt
Sh x 2
Small Metal Washer
G
B
B
inside
Sc
Sh
B
Sr
Sr x 2
Small Locker Washer
FRONT
H
I
J
J
J
I
I
J
Attach Leg Support Bar to Side Panel
9Connect Left and Right Arms to Rear and Front Connector Bar

7
Assembly
10
Sk x 2
Plastic Washer
Sj x 2
Nut
Si x 2
Large Metal Washer
Sg x 2
M8 x 77L Bolt
Note: the side of the seat with “front” label should be in accordance with the side with label of the arm.
Repeat procedure for the other side. Securely tighten all bolts for this step.
K
FRONT
H
K
Sg
Sk Sj
Si
I
H
Attach Seat and Back to Left and Right Arm
11
Note: Hanging bars with top sticker should be on top.
Sl x 2
Hook
L
M
L
M
I
H
K
TOP
TOP
TOP
L
M
Sl
M
K
L
H
K
M
Attach Hanging Bars to Top Crossbar
E
SI
12
Sm x 16
Lawn Stake
Repeat procedure for the other side and other three leg posts.
A
R
Q
Sm
Attach Lawn Stakes to Post Base and Base Plate
13
Note: the canopy should be placed under the brackets.
P
N
F2
N
F2
N
Attach Canopy to Canopy Cross Bar

8
15
16
The support bar on the back of seat and back (K) should be inserted into the U-shaped brackets at the same
time by 2 people and firmly pressed into place keeping the bed steady. Replace cushions.
Printed in China
Remove the cushions. Remove the Hanging bar (M) from the pin bolt on the seat back(K).
Converting Swing to Canopy Bed
Assembly
Locking Canopy Bed in place
14
O
O
N
Insert Canopy Side Bar into Canopy and Attach Cushion (Swing is ready for use)
Note: The Broyhill Logo located on one of the
Base Plates should be positioned on the front
left post as you face the swing.
M
K
K
G
K
G
G
K
K
G
M
L
N