Rowlinson SS354B User manual

Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
•Drill all components where indicated.
Recommended tools for assembly
•Cross head screw driver
•Drill with 3mm diameter drill bit
x 2 Drill
No. Fixing Kit Qty.
17 Black T-hinge 8
18 Towerbolt and catch plate 3
19 Chains 4
20 70mm screws 2
21 50mm screws 30
22 40mm screws 2
23 25mm black screws 81
24 19mm black roundhead screws 24
25 19mm silver roundhead screws 4
1
2
3
4
5
6
7
8
9
10
11
12
7. Bolts
Position a towerbolt at the top of each door and their catch plates on the door header strip as shown. Ensure the bolts
align with the catch plates so that the bolts fits in the catch plate when in the locked position. Secure each bolt using
4 x 19mm black round head screws and 4 x 19mm black round head screws for each catch plate. Position a third tower
bolt and catch plate in line with the bottom door hinges. Attach the bolt to one door and the catch plate to the other.
Ensure the bolt slides into the catch plate and fix using 4 x 19mm black round head screws and 4 x 19mm black round
head screws for each catch plate.
Pent Double Bin Store
Assembly Instructions
English SS354B
13
15
14
No. Components Qty.
1Back panel 2
2Left side panel 1
3Right side panel 1
4Back panel joint rail (35x28x250mm) 1
5Lid stay block (35x28x150mm) 2
6Door frame uprights (28x28x1090mm) 2
7Door header frame (45x28x1330mm) 1
8Base rail (45x15x1330mm Beveled) 1
9Door hinged strip (63x12x1115mm) 2
10 Header strip (50x12x1424mm) 1
11 Lid hinge strip (50x12x1500mm) 1
12 Left door 1
13 Right door 1
14 Left lid 1
15 Right lid 1
16 Lid stay (28x15x650mm) 2
16
17
18 19
19mm
black
19mm
black
19mm
50mm
Using the bin store
Position the bin inside
the store, loop the
chains around the
handles of the bin and
attach the S hook to one
of the chain links.
Ensure the lid of the bin
shuts fully when the lid
is down.
Biocidal Products Regulation EU 528/2012
Permawood ACQ1900 treated wood is a treated article that incorporates biocidal
products: copper hydroxide and Benzalkoniumchloride. They protect wood against
fungal decay /rot/ and insect attack.Keep away from food, drink and animal feeding stuffs.
Avoid breathing dust when cutting treated wood.
2016 © Rowlinson Garden Products Ltd
If in doubt of any aspect regarding the assembly, use or safety of your bin store please contact us :
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.ukv
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
8. Lid stays & chains
Secure a lid stay to the inside of the side panel top frames, using 1 x 50mm screw per stay. Attach two chains to each
lid. Screw through the end link of each chain into the side of the lid frames as shown using 1 x 19mm silver round head
screw for each chain.

1. Back panels
Secure the two back panels together as shown below using 4 x 50mm screws. Attach the back panel joint rail to the bottom
frame of the back panel assembly, align centrally over the join between the two panels.
4. Lid stay support blocks, hinge & header strips
Attach the door hinge and header strips as show using 7 x 25mm black screws for the header strip. For each door hinge
strip use 6 x 25mm black screws. Fit the lid stay blocks to the rear frames of the side panel just below the top frame.
secure each block using 2 x 50mm screws. Position the Lid hinge strip centrally on top of the back panels and secure
down using 6 x 25mm black screws.
Drill
Drill pilot holes for each
screw in this section.
50mm
50mm
50mm
Important Note:
Leave a 15mm gap to
allow for the thickness
of the base rail. 40mm
70mm
2. Side panels
Secure each side panel to the back panel using 4 x 50mm screws per panel. Screw through the frame of the side panel
into the frame of the back panel
Drill
Drill pilot holes for each
screw in this section
50mm
50mm
3. Door frame & front base rail
Position the door frame uprights against the inside front frames of the side panels, leave a gap of 15mm (thickness of the
base rail) from the bottom of the panel and secure each upright using 4 x 50mm screws. Attache the base rail to the
bottom of the door frame uprigths, using 1 x 40mm screw at each end. Fit the door header frame to the top of the
uprights using 1 x 70mm screw at each end.
25mm
black
25mm
black
50mm
25mm
black
25mm
black
Important Note:
ensure the frame squares
are at the top and in the
middle of the assembly.
25mm
black
6. Lids
Position each lid on top of the assembly. Secure to each lid two T-hinges using 4 x25mm black screws per hinge. Ensuring
the hinges are aligned with the lid framing. Fix each hinge to the hinge strip using 3 x25mm black screws per hinge.
5. Doors
For this stage it may be easier to tip the assembly onto its back. Position the doors in place. Note that on the inside the
square pieces of framing must be at the top and in the middle of the assembly. Secure to each door two T-hinges using
4 x25mm black screws per hinge. Ensuring the hinges are aligned with the door framing. Fix each hinge to the hinge strip
using 3 x25mm black screws per hinge.