BEST SANITIZERS BSX Boot Scrubber Series User manual

USER MANUAL
BSX900-DAF
Compact Walk Through Boot Scrubber

BSX900-DAF User Manual Page 2 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
!WARNING:
1. All personnel using this unit must be familiar with
the informaon contained in this manual. Follow all
installaon and maintenance instrucons.
2. Always wear appropriate footwear. Secure or remove
loose items on footwear.
3. Ensure solid foong and use both hands when operang
the unit.
4. Avoid contact of chemicals with skin and eyes. If contact
occurs, see SDS sheet for further rst aid measures.
5. Follow safety instrucons of chemical manufacturer
(SDS).
6. Always follow plant and OSHA guidelines about the use
of equipment.
7. Disconnect power before servicing equipment.
8. Always follow safety precauons and obey warning
labels. Failure to do so could result in injury or death.
Table of Contents
System Requirements
Installaon
Physical Set-Up
Plumbing Connecons
Motor Speed Adjustment
Operaon
Start Up
Use
Shut Down
Cleaning
Opening Grate
Removing Brushes
03
05
05
06
07
07
07
08
08
Removing Steps
Removing Spring Balancer
Advanced Conguraon
Motor Current Sensor
Brush RPM Adjustment
Drive Parameters
Timing Relay
Maintenance
Troubleshoong
Appendices
Parts Callouts
Electrical Schemacs
09
09
10
10
11
11
12
13
15
23

BSX900-DAF User Manual Page 3 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Water Supply
• Flow: 1.5 GPM (3.8 L/m) minimum*
• Pressure: 30-60 psi (207-414 kPa)**
• Temperature: 40-100⁰F (4-38⁰C)
Minimum 3/8" supply piping size recommended
*Minimum pressure must be maintained during
specied water ow!
**For consistent operaon of Venturi Injector and
spray nozzles, a water pressure regulator and lter is
recommended.
Electrical
• 115VAC, single phase, 60Hz, 19.1A
(BSX900-DAF-115V)
• 230VAC, single phase, 60Hz, 13.7A
(BSX900-DAF-230V)
• 480VAC, triple phase, 60Hz, 3.9A
(BSX900-DAF-480V)
The BSX900-DAF is a compact walkthrough, sole-only,
footwear scrubbing unit built to accommodate 1 user
at a me with the ability to put through 15-25 users
per minute.
The included user manual contain installaon,
operaon, and maintenance instrucons for all
BSX900-DAF (115V, 230V, or 480V) Boot Scrubbers.
The reference images and diagrams contained within
will vary by model, but are subject to the same
procedures as outlined.
For further support or informaon please contact
your sanitaon representave or Best Sanizers, Inc.
technical support.
Overview
NOTE: A back ow preventer must be installed
in the water line to this unit. Check local
codes to ensure proper installaon.
System Requirements
!
WARNING:
DO NOT EXCEED maximum water
temperature! Damage to brushes can result.
• Construcon: 304L stainless steel, UHMW,
Polypropylene
• Weight: 425 lb (192.78 kg)
• Dimensions: 62 7/8” x 45 3/8” x 54 3/4”
(1,597 x 1,152.5 x 1,390.65 mm)
• Water Consumpon: 0.75-1.5 GPM
(2.8 - 3.8 L/m)
• Minimum Chemical Diluon Rao: 1:230*
Specicaons
*NOTE: Unit tested at 70°F using water with
30-50 psi injector inlet pressure and capillary-
tube style injector metering p.
PO Box 1360
Penn Valley, CA 95946
www.bestsanizers.com
WARRANTY
One year warranty on all parts and components.
Warranty void if unit is misused, modied, serviced by
anyone other than an authorized technician, or used
with an incompable chemical. We recommend using
Alpet® No-Rinse Quat Sanizer.
Quesons? Call us at 888.225.3267

BSX900-DAF User Manual Page 4 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
NOTE: For xed installaons, area in front of electrical panel must have at least 36" of clearance.
Installaon

BSX900-DAF User Manual Page 5 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Physical Set Up:
1. Set unit in desired locaon.
2. Aspects to consider when deciding on placement:
• Clearance for entering and exing
• Locaon of drain
• Emergency exit paths or egress in case of
emergency
• Head room for personnel while using the unit
• Access to control box
• Connecons for water and electricity
3. Use a level to make sure the unit is stable and
leveled at each end of the tub [Figure 5.1].
4. Connect unit to electrical supply.
Plumbing Connecons:
1. Connect water source to solenoid valve quick
ng inlet using 1/2" Polyethylene tubing or
similar [Figure 5.2].
2. If necessary, adjust the diluon rao by selecng
an appropriate metering p (included) and test.
• The smallest metering p is a yellow p with a
small tube aached [Figure 5.3].
• This tube can be trimmed to alter the diluon
rao.
• Full length capillary tube results in a diluon
rao of approximately 1:670 at 30-50 psi
water inlet pressure.
3. With the metering p installed, connect soluon
source to orange hose barb of the Venturi Injector
(located above water inlet) using 1/4" clear PVC
tubing (included) [Figure 5.2].
Installaon
NOTE: To move the unit use a pallet jack or
a hi-lo to li from the boom or using the
handrails. Pad the forks to protect the nish.
Fig. 5.2: Water and Venturi Injector (soluon) inlets
Capillary
Tube
Addional
Metering Tips
Fig. 5.3: Metering Tips and Capillary Tube
Fig. 5.1: Level and stabilize unit using level against end cap of tub

BSX900-DAF User Manual Page 6 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Motor Speed Adjustment
The speed of the motor is controlled by a variable
frequency motor drive. As the drive decreases the
frequency of the motor, the RPMs decrease. The V.F.
drive displays the Hz. on a small display and the knob
next to it adjusts the Hz. The worm gear reducer has a
20:1 rao.
Default: 1750 RPM at 60 Hz.
To adjust the speed:
1. Open the control box.
2. Acvate the sensor to turn on the motor.
3. As the motor is spinning, the unit will display the
operang speed in Hz.
4. Turn the knob counter-clockwise to decrease the
Hz, therefore decreasing the RPMs. Turning the
knob clockwise will increase the RPMs [Figure 6.1]
5. Adjust the Hz. on the variable frequency drive to
the desired brush speed. The minimum frequency
is 15 Hz and the maximum is 60 Hz. Best
Sanizers, Inc. recommends 70 RPM/48 Hz.
Installaon (connued)
!
DANGER:
Do not open control box during wash down
or cleaning. Only authorized personnel should
open the control box.
Speed
Adjustment
Fig. 6.1: PowerFlex 4M Variable Frequency Drive

BSX900-DAF User Manual Page 7 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Operaon
Fig. 7.2: Grate triggering Prox Switch (some components
hidden for clarity)
Start Up
1. Verify installaon has been completed:
• Brushes are secure
• Walkway grate is lowered
• Unit is plugged in and receiving power
• Water and soluon have been plumbed and
lines are open
2. Pull the E-STOP switches up and engage power,
the E-STOP will illuminate red when the unit is
receiving power [Figure 7.1].
Use
1. Step onto the walkway grate.
2. The walkway grate will depress, acvang a
proximity sensor which starts the brush rotaon
and soluon spray [Figure 7.2].
3. Walk through the unit, allowing the rotang
brushes to clean by moving the boot to make
contact with hard to reach areas.
4. One second aer the user steps o of the
walkway grate the brushes and sanizer will stop.
Shut Down
• Press the red E-STOP buon on the control box.
• Disconnect power and follow lockout-tagout
procedures as necessary.
!
CAUTION:
When operang: always ensure solid foong
and use both handrails for stability.
NOTE: Prior to placing footwear into the unit,
test that it is working properly by acvang
the sensor (put weight on the grate).
Fig. 7.1: E-STOP indicator light on control box

BSX900-DAF User Manual Page 8 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Cleaning Procedures
Fig. 8.1: Grate Liing, shown on BSX1000S-DAF
!
CAUTION:
Failure to latch the grate properly could result
in grate falling closed unexpectedly.
INCOMPLETE COMPLETE
Fig. 8.2: Grate Latch Orientaon
!
CAUTION:
Use of high pressure (above 400 PSI) is not
recommended on sensive areas such as electrical
components, motors, or gearboxes.
Removing & Replacing Brushes
1. Shut down the unit and open the grate.
2. Li each brush out of the tub by grabbing the
open end and liing up [Figure 8.3 - Arrow 1].
3. With the open end lied, the brush can be
detached from its anchor [Figure 8.3 - Arrow 2].
4. Repeat this process to remove the other brush.
5. Brushes can be washed individually in a COP tank
or wash machine.
6. The tub can be washed by convenonal means.
NOTE: It is NOT recommended to use hot water
(over 120°F) to clean brushes.
Fig. 8.3: Brush removal process
2
1

BSX900-DAF User Manual Page 9 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Cleaning Procedures (connued)
Removing Steps
1. Shut down the unit.
2. Grab either side of the step by the handles.
3. Li up to remove from tub [Figure 10.1].
4. Steps can be washed individually in a COP tank or
wash machine.
5. Replace steps before enabling power and/or use.
Removing Grate Springs & Balancer
1. Open the Grate.
2. Rotate the Spring Balancer Weldment backward
to provide enough clearance to remove the Spring
assembly [Figure 10.2].
3. Li the opposing end of the Balancer Weldment
into the upper secon of its keyhole.
[Figure 10.3 - Arrow 1]
4. Slide the Balancer through the upper secon of
the keyhole to release the other end.
[Figure 10.3 - Arrow 2]
5. Li the free end up while sliding the Balancer out
the keyhole to completely remove from the tub.
[Figure 10.3 - Arrow 3]
6. Springs and Balancer Weldment can be washed
individually in a COP tank or wash machine.
Fig. 10.1: Step removal
Fig. 10.2: Balancer Weldment rotaon to remove Spring
Fig. 10.3: Balancer Weldment removal procedure
32
1
12

BSX900-DAF User Manual Page 10 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Advanced Conguraon Opons
Motor Current Sensor
The motor current sensor monitors the current draw
of the motor and will stop the motor if an over-torque
condion occurs, resulng in an F002 fault code on
the VFD.
Default Set Point = 10 turns clockwise
Raise the Set-Point:
1. Turn screw clockwise ½ turn and test
To Start Over:
1. Turn screw counter-clockwise unl it clicks.
2. Turn the screw clockwise 10 turns and test.
The sensor also features a me delay that is
adjustable from 0.12 to 15 seconds. The current draw
of the motor MUST exceed the me delay set point
connuously for this duraon in order for a fault to
occur.
Default Time Delay = 1/8 turn (about 0.3sec / 300ms)
!
DANGER:
Do not open control box during wash down
or cleaning. Only authorized personnel should
open the control box.
Brush RPM Formula:
The formula for calculang Speed in RPM from Drive
Frequency in Hertz is:
[Motor Nameplate RPM] x [Drive Frequency (Hz)]
÷ [Motor Nameplate Frequency (Hz)] ÷ [Gear
Reducon]
Example:
• Motor Nameplate RPM = 1750
• Motor Nameplate Frequency (Hz) = 60
• Gear Reducon = 20
• Drive Frequency (Hz) = 48
= 1750 x 48 ÷ 60 ÷ 20 = 70 RPM
The formula for calculang Drive Frequency in Hertz
from Desired Speed in RPM is:
[Desired Speed RPM] x [Gear Reducon] x [Motor
Nameplate Frequency (Hz)] ÷[Motor Nameplate
RPM]
Example:
• Desired Speed in RPM = 70
• Gear Reducon = 20
• Motor Nameplate Frequency (Hz) = 60
• Motor Nameplate RPM = 1750
70 x 20 x 60 ÷ 1750 = 48 Hz
SET-POINT
Fig. 11.1: Current Sensor Sengs Idencaon
TIME DELAY

BSX900-DAF User Manual Page 11 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Advanced Conguraon Opons (connued)
Drive Parameter Sengs
PowerFlex 4M Variable Frequency Drive
Timing Relay Sengs
Eaton TRL04
• Funcon: R (O Delay)
• Time Range: 1 sec.
Schneider Electric Magnecra
• Funcon: S (O Delay)
• Time Range: 1 sec.
FUNCTION
TIME RANGE
ADJUSTMENT RANGE
Fig. 12.1: Eaton TRL04 Seng Idencaon
Parameter
Number Descripon Seng Units
P102 Motor NP Hertz 60 Hz
P103 Motor OL Current 1.7 A
P104 Minimum Freq 15 Hz
P105 Maximum Freq 60 Hz
P106 Start Source 2 n/a
P109 Accel Time 1 s
P110 Decel Time 2 s
t201 Digital In1 Sel 3 n/a
t221 Relay Out Sel 1 n/a
!
DANGER:
Do not open control box during wash down
or cleaning. Only authorized personnel should
open the control box.
FUNCTION
TIME RANGE
ADJUSTMENT RANGE
Fig. 12.2: Schneider Magnecra Seng Idencaon

BSX900-DAF User Manual Page 12 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
The following maintenance procedures are
recommended for normal use. Units which see a
high amount of daily use should be inspected more
frequently as necessary.
General Maintenance Instrucons
The below maintenance procedures are recommended for
normal use. Units which see a high amount of daily use
should be inspected more frequently as necessary.
Daily:
• Thoroughly clean and sanize unit, brushes and
components.
• If running mulple shis, clean aer every shi if
possible.
• Test chemistry for proper diluon.
Weekly:
• Check unit for proper sensor funcon and brush
rotaon.
• Ensure spring loaded grate (if applicable) is
funconing properly.
• Inspect brushes for damage or wear. Check for
missing or deformed bristles.
• Inspect electrical cords and plumbing for
damage.
• Inspect and test funcon of emergency stop
switches.
Monthly:
• Check all fasteners to ensure they are ght.
• Ensure warning labels and decals are present
and in good condion.
• Inspect motors, gearboxes, and reducers for
signs of oil leakage.
• Inspect electrical enclosure for signs of water
intrusion.
• Inspect sensors for damage.
• Inspect moving parts for damage or wear.
Quarterly:
• Inspect structure for cracked welds or bent
components.
Opening Grate
1. Shut down the unit (see pg. 5) and li the grate
up by its handle [Figure 8.1].
2. Swing the grate open completely
Latch into place against the pin aached to the
corner rail [Figure 8.2].Gear Reducer:
• The gear reducer is supplied lled to capacity
with Mobil Cibus SHC 634 NSF H1 Food Grade
or equal synthec oil.
• The synthec lubricaon provided is
good for ambient temperatures -10°F -
105°F and is compable with standard
compounded oil.
• Oil should be changed every 2 years (or 6,000
operang hrs.)
• Designed with a bladder type vent system:
• Consists of an internal bladder that
seals the oil chamber from the outside
environment at all mes - as pressure
builds, the bladder contracts keeping the
internal pressure to a minimum.
• Advantage: The internal oil chamber is
completely sealed, ensuring oil is not
released causing contaminaon in the
applicaon.
Motor:
• Inspect at regular intervals.
• Keep clean and venlang openings (on TEFC
motors) clear of any obstrucons.
• Verify the mounng bolts and couplings
to ensure that they are ght and properly
adjusted.
• Motor bearings are sealed and not
re-greasable.
• Bearings should be replaced approximately
every 5 years for 8 hr./day service.
Preventave Maintenance
NOTE: Control box is equipped with a Lock-Out/
Tag-Out switch for restricted power access when
performing maintenance procedures.

BSX900-DAF User Manual Page 13 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Unit will not operate:
• Follow the startup procedure (pg. 7)
• Verify the control box is closed and the power-
disconnect switch is in the ON posion.
• Verify that there is power going to the unit.
• Verify the circuit breakers in the building
have not been tripped.
Unit will not spray:
• Verify water pressure at the inlet to the water/
soluon solenoid (35 psi min.)
• Inspect spray nozzles for clogging.
• Verify that the orange LED light on the solenoid
valve connector illuminates when the brushes
are rotang.
Green START buon is illuminated, but one
or more brushes will not rotate when unit is
acvated:
• Power cycle the unit by turning the disconnect
switch to OFF and then back to ON. Follow the
start up procedure on Page 7.
Unit is leaking onto oor:
• Check to make sure all joints are sealed.
• Verify water and soluon inlets are aached and
rmly in place.
Leaner Diluon Raos Required:
• Verify metering p is installed in the injector
chemical inlet hose barb
• Use the yellow “Capillary Tube” style metering p
(see pg. 5 for further informaon)
• If the desired diluon rao sll cannot be
achieved pre-diluon of the chemical may be
necessary.
Troubleshoong
Venturi will not draw Chemical Soluon:
• Verify water supply is sustaining 30 psi at the
injector inlet while unit is running
• Elevate the chemical jug above the injector (a jug
hook is provided for this purpose)
• Verify spray nozzles are not clogged. The nozzles
supplied with the equipment are rated at 0.2GPM
@ 10psi (0.28GPM @ 20 psi)
• Ensure the sucon lter is not clogged, kinked or
obstructed in any way that would restrict ow.

BSX900-DAF User Manual Page 14 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
F002 Fault Code on Variable Frequency Drive:
Cause: Power may have been cycled to the unit
while it was “ON”. To solve:
1. While power is sll applied, turn the unit “o”
by pushing down hard on the e-stop buon
2. Wait at least 5 seconds, then pull the e-stop
buon out again. DO NOT stand on the
walkway grate during this process.
3. The unit should now be ready for use.
Cause: If the brushes stop suddenly during normal
use and the fault is displayed, the Motor Current
Sensor set point may be too low. To solve:
1. Turn the set point adjusng screw clockwise ½
turn to raise the set point and re-test.
F004 Fault Code on Variable Frequency Drive:
• If unit is connected to a GFCI, verify its rangs
(class, mA restricons, etc.)
• Verify minimum frequency seng on VFD is set
between 15 to 20 Hz.
• VFD Parameter: P104 [Minimum Freq.]
• Manufacturer Default: 30 Hz.
• Set the lowest carrier frequency on the VFD
(lower carrier = less switching on/o)
• VFD Parameter: P446 [PWM Frequency]
• Manufacturer Default: 4.0 kHz.
• Minimum: 2.0 kHz.
Troubleshoong (connued)
NOTE: Best Sanizers, Inc. recommends
Leviton's GFI protecon device [# GFRBF-W]
for circumstances where the facility's original
GFCI plug is not applicable.

BSX900-DAF User Manual Page 15 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Appendix A - Parts Callout (BSX900-DAF)
USP20119

BSX900-DAF User Manual Page 16 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Appendix A - Parts Callout (BSX900-DAF)
Part No. Descripon
F1000 STANDOFF 1/4-20 x 1/2 x 1/2 SS
F1040 BOLT HHC 5/16-18 x 1-1/4 SS
F1047 NUT NYLOCK 1/4-20 SS
F1052 NUT NYLOCK 5/16-18 SS
F1056 WASHER 1/4 SS TYPE A
F1066 NUT NYLOCK 10-32 SS
F1078 WASHER .5 X .88 X .06 UHMW
F1083 BOLT HHC 1/4-20 x 1-1/4 SS
F1085 WASHER FENDER 5/16-18 SS
F1088 BOLT HHC 1/4-20 X 1-3/4 SS
F1126 BOLT HHC 10-32 X 1 SS
F1130 BOLT HHC 5/16-18 X 5/8' SS
F1135 STANDOFF 1/4 X 1/2 X 3/16 SS
F1136 STANDOFF 1/4 X 1/2 X 1 SS
F1139 BOLT SHUTTER 1/4-20 X 1 SS
F1166 BOLT HHC 5/16-18 X 2-1/4' SS
M1134 SOLENOID BRACKET
M1183 DRIVE SHAFT MOTOR-BRUSH WELDMENT
M1237 GRATE LATCH
M1420 BRUSH SUPPORT WELDMENT
M1534 SPACER .313 X .5 X 1.5
M1720 BRUSH BSX HORIZONTAL SOLE
M1746 BSX JUG HOOK
M1758 BSX GRATE STEPPED HINGE PIN
M1795 BSX FORMED STEP 24 INCH
M1850 BSX1000 GEN2 SPRAY NOZZLE RISER
WELDMENT
M1851 BSX1000 GEN2 PIPE NIPPLE
M1852 BSX1000 GEN2 MOTOR COVER
M1892 BSX SPRING BALANCER WELDMENT V3
M1894 BSX C-CHANNEL GRATE LIFT PIN GLIDE
M1896 BSX GRATE SPRING ASSEMBLY
M1904 BSX SPRING BALANCER BEARING ROUND
M1905 BSX SPRING BALANCER BEARING SLOTTED
M1981 BSX900 TUB WELDMENT
M1982 BSX900 SPRAY MANIFOLD WELDMENT
Part No. Descripon
M1986 BSX900 GRATE V3 WLDMNT
P1005 STERLING SS MOTOR 1/2HP, 1800 RPM,
230/460/3/60, TENV, 56C FOOTLESS
P1006
STERLING GEAR REDUCER 20:1, 56C, HOLLOW
QUILL, .625 HOLLOW OUTPUT, 1.33" CENTER
DISTANCE,
P1046 VALVE, SOLENOID, 3/8" SS 24VDC DIN COIL, DEMA
463PS.4D
P1121 Induce Proxy 18mm PP 8mm RN 4-Wire DC
N.E./M.C. M12 IQ/D Shielded
P1147 CORD GRIP 1/2 NPT X .170-.450 BLK HEYCO M3231
P1148 CORD GRIP NUT 1/2' NPT BLACK - HEYCO 8463
P1187 SOLENOID CABLE 18MM DIN 24V LED 3M SC18-
LS24-3
P1242 TERMINAL, 1/4" RING, 14-16 AWG INS
P1252 PIPE PLUG 1/4" NPT SOCKET HD SS
P1331 1/2" OD POLYETHYLENE TUBING - NATURAL
P1400 CABLE, M12, 4 POLE, 5m (16.48 ), RT-ANG
FEMALE/AXIAL MALE
P1418 QUICK FIT ADAPTER 3/8 NPT X 1/2 TUBE PP
P1511 QUICK FIT STEM ELBOW 1/2' X 1/2'
P1599 METERING TIP, CAPILLARY TUBE
P1769 METERING TIPS, ULTRA LEAN 100-15KU
P1828 WIRE, VFD-MOTOR, 14 AWG, 4-CONDUCTOR,
SHIELDED, XLPE/PVC
P1830 PIPE ELBOW 3/8" x 90 304SS
P1903 VENTURI INJECTOR DEMA ROCKET, ORANGE,
.070", 1.3GPM@100PSI, SINGLE BARB
P1934 GREASE, ELECTRIC INSULATING .17OZ ONE TIME
USE PACK
P1944
NOZZLE, FAN SPRAY, 110 DEGREE, 1/8 MNPT,
304SS, FLOODJET TYPE K, 0.2 GPM @ 10 PSI
(1/8KSS-2)
P1945 VENTURI INJECTOR 1/4" SUCTION LINE AND
STRAINER
P1946 VENTURI INJECTOR SUCTION WEIGHT CERAMIC
FOR 1/4" TUBE

BSX900-DAF User Manual Page 17 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Appendix A - Parts Callout (M1987 : 115V, 1PH)

BSX900-DAF User Manual Page 18 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Appendix A - Parts Callout (M1987 : 115V, 1PH)
Part No. Descripon
F1059 NUT NYLOCK 3/8-16 SS
F1140 WASHER SEALING 3/8" ID 1" OD SS
F1172 SCREW THREAD FORMING 10-32 X 1/2 HEX WASHER
HEAD ZINC
F1177 BOLT HHC 3/8-16 X 2-1/2 SS
M1517 BACK PANEL CP2016
M1819 SPACER 3/8" X 1-1/2" SS
P1111 ENDSTOP PHOENIX CONTACT 3022276 CLIPFIX 35-5
P1122 POWER SUPPLY RHINO 24VDC 60W PLASTIC CASE
P1147 CORD GRIP 1/2 NPT X .170-.450 BLK HEYCO M3231
P1148 CORD GRIP NUT 1/2' NPT BLACK - HEYCO 8463
P1184 CORD GRIP 1/2 NPT X .095-.260 BLK HEYCO M4518
P1228 ENCLOSURE SS 20x16x8 SLOPED TOP HOFFMAN
P1232 IEC CONTACTOR 3P 12A 24VDC COIL 1 N/O AUX
CONTACT
Part No. Descripon
P1325 CIRCUIT BREAKER EATON WMZT2D13
P1347 VARIABLE FREQUENCY DRIVE POWERFLEX 4M 1/2HP
240V 1PH
P1361 CORD GRIP 3/4 NPT X .435-.705 BLK HEYCO M3234
P1585 WIRE SJOOW 12AWG 4 CONDUCTOR BLACK (0.650
OD) 600V 02726.41T.01
P1711 INDICATOR LIGHT 24V MODULAR LED GREEN
P1819 DISCONNECT SWITCH 25A 3-POLE
P1820 DISCONNECT HANDLE KIT RED/YELLOW FOR P1819
P1873 TERMINAL BLOCK SPRING CLAMP 5.1mm GRAY
P1874 TERMINAL BLOCK SPRING CLAMP 5.1mm GROUND
P1880 TERMINAL JUMPER 5.1mm
P1939 RELAY, TIMER, MULTIFUNCTION 24VDC
P1940 SWITCH, CURRENT SENSING WITH TIME DELAY,
1-175A ADJUSTABLE, FIXED CORE, NC

BSX900-DAF User Manual Page 19 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
General
Installaon
OperaonAppendix Maintenance ConguraonTroubleshoong
Appendix A - Parts Callout (M1888 : 230V, 1PH)

BSX900-DAF User Manual Page 20 of 25 Updated: 06/25/19
USER MANUAL: BSX900-DAF
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Appendix A - Parts Callout (M1888 : 230V, 1PH)
Part No. Descripon
F1059 NUT NYLOCK 3/8-16 SS
F1140 WASHER SEALING 3/8" ID 1" OD SS
F1172 SCREW THREAD FORMING 10-32 X 1/2 HEX WASHER
HEAD ZINC
F1177 BOLT HHC 3/8-16 X 2-1/2 SS
M1517 BACK PANEL CP2016
M1819 SPACER 3/8" X 1-1/2" SS
P1111 ENDSTOP PHOENIX CONTACT 3022276 CLIPFIX 35-5
P1122 POWER SUPPLY RHINO 24VDC 60W PLASTIC CASE
P1147 CORD GRIP 1/2 NPT X .170-.450 BLK HEYCO M3231
P1148 CORD GRIP NUT 1/2' NPT BLACK - HEYCO 8463
P1184 CORD GRIP 1/2 NPT X .095-.260 BLK HEYCO M4518
P1228 ENCLOSURE SS 20x16x8 SLOPED TOP HOFFMAN
P1232 IEC CONTACTOR 3P 12A 24VDC COIL 1 N/O AUX
CONTACT
Part No. Descripon
P1325 CIRCUIT BREAKER EATON WMZT2D13
P1347 VARIABLE FREQUENCY DRIVE POWERFLEX 4M 1/2HP
240V 1PH
P1361 CORD GRIP 3/4 NPT X .435-.705 BLK HEYCO M3234
P1363 CORD GRIP NUT 3/4' NPT NYLON HEYCO 8465
P1449 Push-Pull Pushbuon, Red, 24V
P1533 250V 30A L6-30 MALE PLUG
P1585 WIRE SJOOW 12AWG 4 CONDUCTOR BLACK
P1819 DISCONNECT SWITCH 25A 3-POLE ALTECH KU325N
P1820 DISCONNECT HANDLE KIT ALTECH OKA/KU LK10 Y/R
P1873 TERMINAL BLOCK SPRING CLAMP 5.1mm GRAY
P1874 TERMINAL BLOCK SPRING CLAMP 5.1mm GROUND
P1939 RELAY, TIMER, MULTIFUNCTION 24VDC EATON TRL04
P1940 SWITCH, CURRENT SENSING WITH TIME DELAY