BETCO PowerBuff AS2600T User manual

- 2 -

TABLE OF CONTENTS
PAGE DESCRIPTION
3 Table of Contents
4, 5 Safety Instructions – Very Important – Must Read Both Pages
6 Procedures for Loading, Transporting, and Unloading Scrubber
7 Specifications of PowerBuff Automatic Floor Scrubbers
8 Battery Installation and Charging
9 Battery Maintenance
10 Preventative Maintenance
11 Pad Driver and Available Scrubbing Brushes
12 Squeegee Information and Adjustments
13 Brush Operation – How to Raise and Lower Brushes
14 Operating Tips and Miscellaneous Information
15 Scrubber View Descriptions for this Manual
16, 17 Operating Procedures – 2 pages
18 Main Scrubber Parts
19 Scrubber Controls
20 Rear View of Scrubber Showing Parts
21 Dashboard Layout View and Parts and Rear View Parts
22 Solution Tank and Lid Assembly and Parts
23 Recovery Tank Assembly and Parts
24, 25 Recovery Lid Assembly and Parts
26 Splash Skirt Assembly and Parts
27 Squeegee Mount Assembly and Parts
28, 29 Squeegee Assembly and Parts
30, 31 Brush Lift, Motor Mount, and Squeegee Lift, and Parts
32, 33 Motor Frame and Motor Mount and Parts
34 Brush Drive Details and Traction Drive Details
35 Drive Hub Assembly and Parts
36 Handle Assembly (for Brush Drive)
37 Handle Assembly (for Traction Drive)
38 Brush Drive Wheel Mounting Assembly and Parts
39 Transaxle Assembly and Parts
40, 41, 42 Vacuum System and Solution System and Parts
43, 44, 45 Views of Scrubber with Major Plastic Removed
46 Batteries and Charger Parts
47 Electrical Panel and Parts and Other Electrical Information
48 Electrical Layout for Brush Motors and Vacuum Motor
49 Electrical Layout for Traction Drive Portion of Scrubber
50, 51 Trouble Shooting
52 Warranty
- 3 -

SAFETY INSTRUCTIONS
Hazard Level Explanation or Description of Hazard Level
Failure to follow safety instructions labeled could
result in severe injury or death to the machine operator or others.
Failure to follow safety instructions labeled could result in
injury to the machine operator or others. Also, machine or property
damage could occur.
Failure to follow safety instructions labeled could result in
damage to the machine or damage to other property.
This manual contains important information about your
machine. Read and understand all instructions before
operating the machine. Failure to read and follow the
instructions could result in injury to the person operating the
machine or injury to others. Damage to the machine or other
property could occur if instructions are not followed.
Do not operate this machine around any solvents, thinners, or other
flammable liquids or materials. Electrical sparks can cause a fire or even
an explosion.
Do not smoke around the machine. Also, keep all sparks and flames
away from the batteries. The batteries generate gases that can cause an
explosion.
Special care needs to be used when working on or near the batteries.
Wear eye protection. Do not lay tools on batteries, as they may short out
battery terminals. Do not wear metal jewelry, as it may short out battery
terminals.
Charging batteries can be dangerous. Be aware that the battery charger
may have a relatively low voltage output, but the current output is very
high and therefore dangerous. Do not operate the charger if any parts of
the charger or charger cords are damaged. Do not stand on a wet floor
when connecting or disconnecting charger to the power outlet or to the
machine.
Safety Instructions are continued on the next page
- 4 -

SAFETY INSTRUCTIONS (continued from previous page)
Battery acid is dangerous. Wear eye and face protection, hand protection,
and body protection when working on and around batteries. If you get
acid on your skin, wash off immediately. If you get acid on your clothing,
remove clothing and wash any skin that was in contact with the clothing.
Baking soda mixed with water will help to neutralize the acid on your skin.
The machine is very heavy, so be very careful when loading, transporting,
and unloading the machine. Follow the “Procedures for Loading,
Transporting, and Unloading Automatic Floor Scrubber” (on a separate
page).
Do not pick up dust; machine is for wet pick-up only.
Keep all body parts, clothing, and objects away from moving parts.
Operate machine from the rear, not from the side.
Disconnect a wire to the batteries before working on the machine.
Do not operate machine with charger plugged in.
Do not operate machine with any parts damaged or missing.
Do not operate close to stairs, loading docks, or other drop-offs. Do not
park machine in such a manner that it could roll, forward or backward, off
a drop-off.
Authorized personnel must perform maintenance and repairs. Do not alter
or modify the machine, unless authorized by the manufacturer.
Do not expose the electrical components to water or excessive moisture.
Always put caution signs around the areas that are being cleaned.
Discharge wastewater properly. Improper discharge of wastewater is
illegal. Understand and follow all Federal, State, and Local laws regarding
disposal of wastewater.
Do not use machine as a “ladder”. Do not use machine as a “forklift” to
push stuff around. Do not ride or let anyone ride on the machine.
Your machine warranty may be voided if parts other than PowerBuff parts
are used.
- 5 -

Procedures for Loading, Transporting, and Unloading
Automatic Floor Scrubber
The machine is very heavy, so be very careful when loading,
transporting, and unloading the machine. Use at least two people
to load or unload the machine.
x Loading Procedure Using a Ramp with a Traction Drive Scrubber
oRamp must be long enough so that climb into van, truck, or trailer is no more than 20
degrees. (This would permit a height of 2’4” for a 7-foot ramp, 2’8” for an 8-foot ramp,
and 3’0” for a 9-foot ramp).
oA short “pre-ramp” may be needed to prevent pad drivers from dragging.
oRamp must be secured to vehicle, and be clean and dry.
oRemove squeegee assembly and pad drivers.
oMachine must be driven straight up the ramp and never at an angle.
x Loading Procedure Using a Ramp with a Brush Drive Scrubber
oIt is not recommended that a brush drive scrubber be loaded using a ramp with an
incline of more than 7 degrees. The machine is not self-propelled and therefore it is
not able to assist itself up a ramp. It is too heavy to manually push up a steep incline.
oIf you must load with a ramp, the incline must be no more than 7 degrees. (This would
permit a height of no more than one foot for an 8-foot ramp).
oRamp must be secured to vehicle, and be clean and dry.
oRemove squeegee assembly and pad drivers.
oMachine must be driven straight up the ramp and never at an angle.
x Loading Procedure Using a Lift Gate
oLift gate must have ample capacity to lift the scrubber
oLift gate must be long enough to accommodate scrubber in the direction that it will be
loaded onto the van. Do not load scrubber sideways, because it is dangerous to turn
the scrubber while on the lift gate.
oWheels must be firmly chocked to prevent scrubber from rolling off the lift gate.
x Securing Scrubber
oScrubber must be secured, so that it will not roll or turn over. Use chocks and tie
downs to secure scrubber.
oPlease be aware that a scrubber is very heavy, and that a metal bulkhead in a van
may not contain scrubber in the event of an accident. The equipment in a van can be
more dangerous than the accident itself.
x Unloading Procedure Using a Ramp with a Traction Drive Scrubber
oRamp must be long enough so that removal can be controlled. Use same height
restrictions as used for loading scrubber.
oRamp must be secured to vehicle, and be clean and dry.
oA small pre-ramp may be needed to prevent pad drivers from dragging.
oMachine must be driven straight down the ramp and never at an angle.
oUse slow forward speed to slow descent as needed.
x Unloading Procedure Using a Ramp with a Brush Drive Scrubber
oRamp must be long enough so that removal can be controlled. Use same height
restrictions as used for loading scrubber.
oRamp must be secured to vehicle, and be clean and dry.
oMachine must be driven straight down the ramp and never at an angle.
oDo not let machine run over you or anyone else as it comes off ramp.
- 6 -

Model AS2600B AS2600T AS3200
Scrub Path 26” offset head 26” offset head 32” symmetrical head
Coverage 30,000 sq. ft. / hour 30,000 sq. ft. / hour 38,000 sq. ft. / hour
Battery Pack 24 volt system 24 volt system 36 volt system
Charger 24 volt - 20 amp 24 volt - 20 amp 36 volt - 20 amp
Run Time 4.5 hours 4 hours 5.5 hours
Vacuum Motor 1 HP - 3 stage 1 HP - 3 stage 1 HP - 3 stage
Brush Motors (Two) 3/4 HP - 200 rpm 3/4 HP - 200 rpm 3/4 HP - 200 rpm
Drive System Brush Assisted 1/2 hp sealed transaxle 1/2 hp sealed transaxle
Wheels Front: two 10” solid
Rear: two 5” castors
Front: two 10” solid
Rear: two 5” castors
Front: two 10” solid
Rear: two 5” castors
Tank Construction Rotational molded
polyethylene
Rotational molded
polyethylene
Rotational molded
polyethylene
Solution tank 24 gallon 24 gallon 24 gallon
Recovery tank 26 gallon 26 gallon 32 gallon
Brushes Two 13” pad holders
(Brushes are optional)
Two 13” pad holders
(Brushes are optional)
Two 16” pad holders
(Brushes are optional)
Forward Speed Walking speed Variable to 290 ft/min
(3.3 mph)
Variable to 290 ft/min
(3.3 mph)
Reverse Speed Walking speed Variable to 145 ft/min
(1.6 mph)
Variable to 145 ft/min
(1.6 mph)
Brush Pressure 80 lbs and 200 lbs 80 lbs and 200 lbs 80 lbs and 220 lbs
Brush Lifting Mechanical Mechanical Mechanical
Squeegee 34” heavy duty curved
tracking squeegee
34” heavy duty curved
tracking squeegee
40” heavy duty curved
tracking squeegee
Dimensions
(no skirt, no squeegee)
52” long
25” wide
43” tall
52” long
25” wide
43” tall
60” long
25” wide
43” tall
Weight with Batteries 685 lbs. 710 lbs. 850 lbs.
Warranty 5 years on parts
10 year on tanks
5 years on parts
10 year on tanks
5 years on parts
10 year on tanks
AUTOMATIC FLOOR SCRUBBER SPECIFICATIONS
- 7 -

BACK OF MACHINE
TOWARD THE OPERATOR
FRONT OF MACHINE
figure 1
RED WIRE TO
SCRUBBER
BLACK WIRE
TO SCRUBBER
BATTERY INSTALLATION AND CHARGING
- 8 -
BATTERY INSTALLATION
xTurn off all switches.
xDrain solution tank and recovery
tank.
xDisconnect recovery dump hose
from hooks on rear of machine
so that recovery tank can lift.
xLift recovery tank lid and tilt up
recovery tank.
xInstall batteries as shown on
figure 1.
BATTERY CHARGING
xPlace the charger on a safe place. Make sure that air can circulate
around the charger. Do not get the charger wet.
xAll switches on scrubber must be off.
xDo not remove battery caps (the caps are vented).
xDo not charge scrubber in a wet area.
xDo not stand in a wet area when plugging in charger to the 110 volt
receptacle or plugging into the scrubber.
xConnect the charging plug from the charger to the charging plug on the
back of the scrubber (item 16)
xPlug in the charger to a properly grounded 110 volt receptacle.
xIndicator needle will rise and then will fall slowly as batteries charge.
xCharger will shut off automatically when batteries are fully charged.

ADD DISTILLED WATER,
AS NEEDED, SO THAT
ELECTROLYTE LEVEL
IS ABOUT 3/4"
ABOVE PLATES.
DO NOT OVERFILL.
DO NOT FILL ABOVE
THE BOTTOM OF
THE TUBE THAT
EXTENDS INTO BATTERY.
KEEP ABOUT 1/4" BELOW
BOTTOM OF TUBE.
KEEP ELECTROLYTE LEVEL
ABOVE TOP OF PLATES.
CHECK ELECTROLYTE
LEVEL IN ALL CELLS
figure 2
- 9 -
ELECTRO-
LYTE
LEVEL
IN
THIS
CELL
IS
JUST
RI GHT
ELECTRO-
LYTE
LEVEL
IN
THIS
CELL
IS
TOO
LOW
ELECTRO-
LYTE
LEVEL
IN
THIS
CELL
IS
TOO
HI GH
IF YOU WOULD LIKE TO LEARN MORE ABOUT BATTERIES
THERE IS A VERY INFORMATIVE PUBLICATION AVAILABLE. IT COVERS SUBJECTS SUCH AS
BATTERY TERMS AND HOW A BATTERY WORKS TO SPECIFIC GRAVITY TESTING WITH A
HYDROMETER AND DIAGNOSIS OF BATTERY PROBLEMS.
YOU CAN OBTAIN A COPY OF THE “BATTERY SERVICE MANUAL” FROM
BATTERY COUNCIL INTERNATIONAL
401 N. MICHIGAN AVENUE
CHICAGO, IL 60611
PHONE [phone]
! ! ! BATTERIES ARE DANGEROUS ! ! !
READ THE SAFETY INSTRUCTIONS
IN THE FRONT OF THIS MANUAL
FOR SPECIFIC WARNINGS
BATTERY MAINTENANCE
xTo receive the longest life from the batteries, charge them when they have between
25% and 50% of a full charge.
xDo not allow batteries to remain in a discharged state for very long, as this shortens
the total battery life.
xBe aware that a discharged battery will freeze easily.
xCheck the electrolyte level weekly. Top off with distilled water as shown in figure 2.
Do not overfill. Make sure that all plugs are tight.
xMake sure battery connections are tight and free from corrosion. A baking soda and
water solution and a wire brush are helpful when cleaning battery connections.
Keep caps on when cleaning batteries, so that electrolyte is not contaminated.

PREVENTATIVE MAINTENANCE ITEMS
Before starting work
x Inspect pads for wear. Replace if needed.
x Turn on brush motors and check battery indicator gauge to assure that there is
enough charge to scrub floor.
After you are finished using scrubber for the day
x Raise squeegee and leave up.
x Raise brushes and leave up.
x Drain and rinse recovery tank, including vacuum shut-off float. Wipe top of tank
clean.
x Clean vacuum intake screen. A small wire brush works well for this.
x Wipe down recovery tank lid and lid gaskets.
x Drain and rinse solution tank (especially if using something other than a very mild
scrubbing solution).
x Charge batteries, if needed. Remember batteries have a longer life if allowed to
discharge sufficiently. Please read “Battery Maintenance” page.
Weekly maintenance
x Check electrolyte level in batteries. See “Battery Maintenance” page for instructions.
x Clean and lubricate caster wheels and caster swivel. There are grease fittings to use
a grease gun. Note: Main 10” wheels do not require lubricating. (They have sealed
ball bearings that cannot be lubricated).
x Wipe surface of machine clean. A silicone product such as “Armor All” will make the
plastic parts look really good.
Monthly maintenance
x Clean battery connections and tops of batteries. See “Battery Maintenance” page for
instructions.
x Inspect scrub brushes for wear (If you have scrub brushes).
x General visual inspection for problems.
Semi-annual maintenance
x Inspect carbon brush wear in brush motors.
x Lubricate all pivot points with a light oil. Porous bushings will absorb some oil to
distribute over time.
x Lubricate brush lift arm sliding surface with a heavy grease. This is located behind
the back panel. Bearing grease may be used.
As needed items
x Adjust squeegee tilt. See “Squeegee Information” page.
x Turn, flip, or replace squeegee blade for streak free pickup.
x Replace intake screen and intake screen gasket.
- 10 -

PAD DRIVER AND AVAILABLE BRUSHES
PAD DRIVER
NEED 2 PER MACHINE
PART NO. DESCRIPTION
E11756 13" pad driver (must be used with an appropriate pad)*
* CONSULT YOUR JANITORIAL SUPPLIER FOR ADVISE
ON THE PROPER PAD TO USE FOR YOUR APPLICATION.
SCRUB AND STRIP PADS ARE COLOR CODED FROM
LEAST AGRESSIVE TO MOST AGRESSIVE AS FOLLOWS:
WHITE - RED - BLUE - GREEN - BROWN - BLACK
BRUSH
NEED 2 PER MACHINE
PART NO. DESCRIPTION USES
E11757 Dynascrub
Light to medium scrubbing (replaces red pads)
E11759 Powerscrub
Medium to aggressive scrubbing (replaces blue or green pads)
E11760 Stratagrit
Very aggressive scrubbing or stripping (replaces brown or black pads)
A BRUSH WILL OUTLAST A PAD AT LEAST 100 TO 1
- 11 -

(a) USE 1/4" HEX KEY
(b) USE 9/16" HEX
WRENCH OR
SOCKET
(c) HOLE IN REINFORCING BLADE IS SHOWN
TURNED UPWARD, WHICH IS THE POSITION
WHICH ALLOWS FOR THE MOST DEFLECTION
OF THE MAIN SQUEEGEE BLADE
SQUEEGEE MUST BE ATTACHED
TO SCRUBBER FOR PROPER
ADJUSTMENT OF TILT AND
BLADE DEFLECTION
- 12 -
SQUEEGEE INFORMATION AND ADJUSTMENTS
Problem: Squeegee is leaving streaks at the center or the ends.
Cause: Squeegee is not level. If it is not level, it will streak in the center or at the ends.
Solution: Make sure that the tips and the center of main squeegee blade are uniformly deflected and
not leaving streaks. Adjust squeegee tilt as follows:
Step 1: Loosen (a) and (b)
Step 2: Tilt squeegee in direction needed for squeegee to deflect uniformly along entire length.
Step 3: Tighten (a) and (b) enough to hold temporarily.
Step 4: Move scrubber forward to check that deflection is uniform.
Step 5: If correct, tighten (a) and (b) as much as you can; or if not correct, start over at step 1.
Problem: Squeegee is leaving streaks not related to squeegee being level.
Cause: (1) Trash under main squeegee blade.
(2) Blade edge is worn or nicked
Solution: (1) Clear trash.
(2) Turn the blade. All four edges can be used. If all edges have been used, then replace the
main squeegee blade.
Problem: Main squeegee blade is deflecting too much or too little.
Cause: Reinforcing blade is turned wrong for the floor conditions.
Solution: Holes on the reinforcing blade are offset. Blade can be flipped to put longer or shorter side
toward floor. Longer side has a hole (c) at center. Facing the hole down makes the main
blade stiffer and allows it to deflect less. Hole turned upward allows blade to deflect more.

RAISE BRUSHES
2
13
BRUSH
HANDLE
FOOT
PEDAL
(2) PUSH DOWN
FOOT PEDAL
FIGURE 1 IF INSTRUCTIONS IN
FIGURE 1 DO NOT WORK,
GO TO INSTRUCTIONS
IN FIGURE 2
TO RAISE BRUSHES
(1) PUSH IN
HANDLE
2
ADD HEAVY
BRUSH PRESSURE
(2) PUSH IN
HANDLE
(3) RELEASE
FOOT PEDAL
SLOWLY
(1 ) PUSH DOWN
FOOT PEDAL
LOWER BRUSHES
(2) PULL BACK
HANDLE,
WHILE STILL
PULLING UP
(1) PULL UP
HANDLE
1
FIGURE 2
(3) LOWER
HANDLE SLIGHTLY
WHILE STILL
PULLING BACK
IF INSTRUCTIONS IN FIGURE 1
DO NOT WORK, THERE ARE
PROBABLY NO BRUSHES ON
SCRUBBER AND THIS
SHOULD RAISE BRUSHES.
IF BRUSHES ARE ON SCRUBBER
AND WILL NOT RAISE, THEY ARE
IN THE HEAVY PRESSURE
POSITION, SO PROCEED TO
FIGURE 5 TO RELEASE BRUSHES.
3
1
3
1
(2) PUSH IN
HANDLE
(1) PULL UP
HANDLE
(3) LOWER
HANDLE
FIGURE 3
2
FIGURE 4 RELEASE HEAVY
BRUSH PRESSURE
3
2
FIGURE 5
- 13 -
1
(1) PUSH DOWN
FOOT PEDAL
HOW TO:
RAISE BRUSHES,
LOWER BRUSHES,
ADD HEAVY PRESSURE
TO BRUSHES, AND
RELEASE PRESSURE
FROM BRUSHES
BRUSH
OPERATION

OPERATING TIPS AND MISCELLANEOUS INFORMATION
FLOOR SCRUBBING TIP
xDouble scrubbing can be a very effective way to clean a floor. This especially important
before coating with finish, as you do not want to wax in any dirt.
xTo double scrub do the following:
xScrub the floor as normal, but leave the squeegee up and the vacuum off.
xScrub a few aisles ahead while letting the floor soak.
xThen go back over what you have wet down, but this time with the
squeegee down and the vacuum on. This will get the floor much cleaner
than a single pass scrub.
Note: Do not double scrub where non-floor cleaning personnel will be walking, since the floor
stays wet and is therefore hazardous.
SQUEEGEE OPERATING TIPS
xThe curved squeegee picks up solution very well if properly adjusted. The squeegee must
be level to work well. If it is not level, it will streak in the center or at the ends. Make sure
that the tips and the center are uniformly deflected and not leaving streaks. If squeegee is
not level, then loosen the two bolts on squeegee bracket and squeegee will pivot forward
and backward. Level squeegee and tighten bolts.
xIf squeegee is properly adjusted and is leaving streaks, then there may be trash caught
under the main squeegee blade. A little trick that will clear most trash is to (1) stop the
scrubber, (2) lift the squeegee, (3) back up a little, (4) lower the squeegee, and then (5)
resume scrubbing as usual. If this does not work, then the trash must be cleared by hand.
xSee “Squeegee Information and Adjustments” page for more information.
IF SCRUBBER IS USED FOR PICKING UP WAX AND STRIPPER
xThe scrubber can be used to vacuum the emulsified wax and stripper from a floor strip. But,
be aware that more upkeep will be required on the scrubber than if it were used only for
scrubbing, since the wax and dirt will remain after the stripper evaporates. So, after using
scrubber on a floor strip do the following.
xDisconnect vacuum hose from squeegee and vacuum clean water through vacuum
hose.
xRinse out recovery tank, including letting clean water run out dump hose.
xClean squeegee.
xClean top of recovery tank.
xClean recovery lid and gasket on recovery lid.
xDrain solution tank and flush lines with clean water. (If you have stripper in the
solution tank, you do not want it on the floor if the next job the scrubber is used on is
just a scrub).
xWipe down anywhere where wax slop has gotten on scrubber.
EXPOSING SCRUBBER TO FREEZING TEMPERTURES
xDo NOT leave scrubber in freezing temperatures
xIf scrubber must be left or transported in freezing temperatures, then
precautions must be taken. If an attempt is made to close (or open) the
solution valve when it is frozen, the solution cable or solution valve will be damaged.
xDrain Solution Tank and leave solution valve open.
xRecovery Tank must also be drained.
xThen after the scrubber is inside place to be used, do not yet attempt to
shut the solution valve. You must first check to make sure that the solution
valve is not frozen. Run hot water into solution tank. After water is running
out the bottom of the machine (the brush area), then shut off solution valve
(do not force the solution valve control handle). You can then fill solution
tank and use the scrubber.
- 14 -

TOP-RIGHT-FRONT
VIEW
- 15 -
RIGHT VIEW
FRONT VIEW
DESCRIPTIONS OF VIEWS
SHOWING PARTS ON SCRUBBER
TOP VIEW
IN THIS MANUAL, MANY OF THE PARTS IN THE DRAWINGS ARE SHOWN
CORRECTLY ASSEMBLED, OR AT LEAST NEAR THE POSITIONS THEY ARE
LOCATED ON THE SCRUBBER.
THIS METHOD WILL HELP TRACE A PROBLEM, FIND WHAT IS NEEDED
TO CORRECT THE PROBLEM, AND THEN PROPERLY REASSEMBLE THE
MACHINE .
THE ELECTRICAL LAYOUT HAS ALSO BEEN SIMPLIFIED, SO THAT
PROBLEMS CAN BE EASILY TRACED AND REPAIRED.

Operating Procedures
(See page 19 for guide to item numbers)
x Batteries need to be in the operating range (the green area) of the battery
condition meter (item 2). Gauge will register battery condition when brush motors
(Brush Motor Control Switch, item 6) are turned on. Turn off brush motors after
battery condition is determined.
x Lift solution lid (item A) and add water and liquid cleaner to solution tank (item B).
Consult cleaner instructions for proper ratio of cleaner and water (Note: the
solution tank holds 24 gallons when full).
x Take scrubber to area to be cleaned
oTraction Scrubber
 Make sure that squeegee and brushes are off the floor.
 Turn variable speed control knob (item 8) all the way
counterclockwise.
 Turn on traction switch (item 9).
 Squeeze forward control lever (item 1) if scrubber needs to go
forward and reverse control lever if scrubber needs to be moved
backward.
 Gradually increase variable speed control knob (item 8) until
scrubber attains the needed speed.
 Release lever to stop.
oBrush Drive Scrubber
 Lift squeegee and brushes off the floor.
 Push scrubber to desired location.
x Lower brushes by depressing brush lift pedal (item 13) and then push in on brush
lift and pressure lever (item 11), and gradually let brushes drop to contact with
floor by slowly lift foot off brush lift pedal (item 13). (Note that the brushes can be
lowered using only the brush lift and pressure lever (item 11)).
x Lower squeegee using the squeegee lift lever (item 18) and turn on vacuum
using the vacuum motor control switch (item 7).
x Turn on solution by adjusting cleaning solution control lever (item 17) to desired
flow rate (the flow rate can be adjusted as the need arises).
x Turn on brushes using the brush control switch (item 6) and immediately move
scrubber forward.
oTraction Scrubber – adjust speed as needed with the variable speed
control knob (item 8).
oBrush Drive Scrubber – push to desired speed. There is no need to keep
the forward control lever depressed. The brush drive scrubber should
move easily by pushing alone.
Operating procedures are continued on the next page
- 16 -

Operating Procedures
(continued)
x When you stop scrubbing an area.
oTurn off brushes (brushes or pads can wear through the wax if left
running in one place)
oTurn off solution flow (cleaning solution control lever (item 17))
oTurn off vacuum (vacuum motor control switch (item 7))
oTurn off traction drive on traction drive model (traction on/off switch (item
9))
x Before taking scrubber back to storage area
oLift brushes
oLift squeegee
x To dump dirty water from recovery tank (item C)
oLift recovery dump hose (item 12) with plug for recovery dump hose (item
10) from hooks.
oHold end of hose so that the dirty solution will flow into the appropriate
place (such as a drain) when plug is removed.
oLoosen T-handle on plug for recovery dump hose (item 10) and remove
plug from hose. Dirty solution will flow from tank. (Note: do not completely
unscrew T-handle from plug).
oReplace plug and tighten. Hang hose back on hooks.
x Machine storage for the day
oBrushes in up position
oSqueegee in up position
oRecovery tank emptied (Note: it is best to occasionally rinse it out with
clean water).
oSolution tank emptied (especially if machine is to be left for longer than a
day).
oTurn off all switches. (Note: if traction on/off switch is left on for more than
20 minutes without the machine moving, then the traction control
electronics will automatically power down. To reset them, simply turn the
traction on/off switch off and then back on).
- 17 -

MAIN SCRUBBER PARTS
4
2
3
1
6
8
7
5
- 18 -
ITEM
SKU
DESCRIPTION AND NOTES
1 E11729 Solution Tank (GRAY)
2 E11728 SOLUTION TANK LID (BLACK)
3 E11754 RECOVERY TANK (GRANITE)
4 E11727 RECOVERY TANK LID (BLACK)
5 E11753 SKIRT (BLACK)
6 E11726 BASE (BLACK)
7 AS261121 Main Frame
8 PE5000 Squeegee assembly - 26"

17
12
10
11
18
16
13
14
15
REAR VIEW
- 19 -
56
2
7
8
9
1
3
4
SCRUBBER CONTROLS
DASHBOARD VIEW
1) Forward Control Lever
2) Battery Condition Meter
3) Reverse Control Lever
4) Circuit Breaker for Vacuum
5) Circuit Breaker for Brush
Motors
6) Brush Motor Control Switch
7) Vacuum Motor Control Switch
8) Variable Speed Control Knob
(Traction Drive Model)
9) Traction on/off switch
(Traction Drive Model)
10) Plug for Recovery Dump Hose
11) Brush lift and Pressure Lever
12) Recovery Dump Hose
13) Brush Lift Pedal
14) Drain Hose for Battery Tray
15) Vacuum Recovery Hose
16) Charging Plug for 24 Volt
Charger
17) Cleaning Solution Control
Lever
18) Squeegee Lift Lever

17
12
10
11
18
16a
13
14
15
21T
25
24
27
22
16b
19
19
20
21B
23
REAR VIEW OF SCRUBBER
NOTE: PARTS LIST IS ON NEXT PAGE
31
30
30
31
29
28
- 20 -