Better Bathrooms BeBa-27528 User manual

WALL MOUNTED LED MIRROR
WITH DEMISTER
BeBa_27528
BeBa_27529
BeBa_27530
•INFRARED SENSOR
•BUILT IN DEMISTER
•IP44 INGRESS PROTECTION
•CAN BE INSTALLED LANDSCAPE OR PORTRAIT

2
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products, for
less.
If you’re after a modern, traditional, or a totally unique style bathroom, we have the
fittings and fixtures to bring your ideas to life, so you can fall in love with your space
every day.
We hope your new product goes above and beyond your expectations. However,
should any problems occur, please:
•Log in to your account and contact our customer services team via your self-service
portal –betterbathrooms.com/CustomerAccount/Login
•Contact us via betterbathrooms.com/contact/contact-us
CONTENTS
SAFETY
3
BATHROOM ZONES
4
PARTS SUPPLIED
5
TOOLS REQUIRED
5
INSTALLING THE MIRROR
6
OPERATION
7
CLEANING AND MAINTENANCE
7
TECHNICAL SPECIFICATIONS
8

3
SAFETY
•This mirror should be installed by a qualified electrician.
•This fitting is only suitable for connection to a 220-240V earthed supply in accordance
with current IEE wiring regulations, and should be installed in accordance with local
Building Regulations.
•This is for domestic, indoor use only.
•The fitting should be connected to a dedicated lighting circuit which must be
protected by a 5-amp fuse (or a 6 amp miniature circuit breaker).
•The electrical connection must be an adequate distance from the rear of the mirror to
prevent the risk of shorting with the mirror’s casing.
•Before installing the fitting ensure that the mains supply is switched off, and that the
appropriate fuse is removed (or appropriate circuit breaker is switched off) before
commencing installation. Ensure that measures are taken to prevent the supply from
being inadvertently reconnected.
•If there is a “Minimum Distance” label, please do not allow flammable materials to
rest within that distance from the unit.
•This product may contain delicate parts –be careful during handling and
maintenance to avoid breakage.
•If any modification is made to the fitting it will invalidate the warranty and may
render the product unsafe.
•A defective appliance may cause electric shock. Never switch on a defective or
damaged appliance. Disconnect the appliance from the mains before seeking
assistance.
•This product is IP44 rated, and no part of the installation is allowed to be within
bathroom Zones 0 or 1. Installation is permitted within Zone 2.
•This product must be earthed. Before commencing installation, ensure that there are
no pipes or wires located behind the wall that may be damaged during drilling.
•Ensure that the hanging location has been decided upon and marked clearly to avoid
unwanted damage to the wall due to incorrect positioning.
•Inspect the mirror to ensure there are no signs of damage prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may damage the mirror
and void your warranty.
•Ensure that the infrared sensor will be easily accessible following installation and that
at least 20cm of space is left around the sensor to ensure correct operation.
•Once installed a bead of silicon can be applied between the mirror and the wall
across the top and sides of the unit. Never seal the bottom of the mirror to the wall,
as this may allow water to accumulate behind the mirror.

4
BATHROOM ZONES
Zone 0:
The interior of the bathtub or shower basin.
Zone 1:
The area around the bathtub or shower basin up
to a height of 2.25m above the floor
Zone 2:
The area stretching to 0.6m outside the bath or
shower and above the bath or shower if over
2.25m

5
PARTS SUPPLIED
WALL PLUGS (X4)
SCREWS M4 (X4)
PLEASE NOTE: It is the installers responsibility to ensure that the fittings are suitable for the type of wall.
Alternative fittings may be required (Not Supplied). If unsure professional advice should be sought.
TOOLS REQUIRED tool
TAPE MEASURE
SPIRIT LEVEL
ELECTRIC DRILL
SCREWDRIVER
HAMMER
8mm DRILL BIT
PENCIL

6
INSTALLING THE MIRROR
NOTE: Ensure that the infra-red sensor will be easily accessible following installation and
that at least 20cm of space is left around the sensor to ensure correct operation.
The mirror comes with the option of hanging both in landscape or portrait orientation. At
the back of the mirror, there are 4 key holes 2 on the vertical side and 2 the horizontal
side.
To hang the mirror, you will need to drill two holes into the wall, ensuring that there are
no wires or pipes behind the wall before commencing.
1. Ensure that the power is disconnected at the circuit breaker,
and that there is no risk of reconnection during installation.
2. Measure the distance between the two key holes.
3. Make a note of the distance and mark their position on the
wall. Use a spirit level to ensure that the holes are level.
4. Drill the 2 holes into the wall at the position marked using a
suitable drill bit.
5. Insert the wall plugs into the holes.
6. Insert the screws into the wall plugs, ensuring their heads are
protruding by approximately 3mm.
7. Check to ensure the screws line up correctly and the mirror can
be safely hung from them.
8. The mirror should now be connected to a suitable fuse spur
following current regulations and guidance. When connecting
ensure that enough cable is left to allow the mirror to be safely
removed.
9. You will now be able to hang the mirror. Carefully lower the
mirror onto the screws, ensuring that is secure and will not
slide.
10. Reconnect the power supply.

7
OPERATION
Your mirror comes with an infrared sensor located on the right-
hand side. To activate the light and de-misting pad, move your
hand across the sensor once at a distance of around 5cm.
To turn it off, move your hand across the sensor again.
SHAVER SOCKET
Your mirror comes with a shaver socket located on the inside of the
mirror. This socket is designed for use only with shavers and other low
voltage devices designed to be powered by a shaver socket.
Once the mirror is connected to the mains, the shaver socket is ready to
use.
CLEANING AND MAINTENANCE
Never use products containing bleach or abrasive cleaners, as these will have a
detrimental effect on the appearance and lifespan of the product.
Use a clean micro fiber cloth to clean the mirror.

8
TECHNICAL SPECIFICATION
Model
BeBa-27528
BeBa-27529
BeBa-27530
WxHxD (mm)
500x700x55
600x800x55
1000x700x55
Net Weight (Kg)
6.5
8.4
11.2
Power Cord length (cm)
60
65
90
Rated Power (W)
32
50
46
IP Rating
IP44
Input
220 - 240V, 50 Hz
This product contains a light source of energy efficiency class F.
DISPOSAL
Recycling facilities are now available for all customers at which you can deposit your old
electrical products. Customers will be able to take any old electrical equipment to
participating sites run by their local councils.
Please remember that this equipment will be further handled during the
recycling process, so please be considerate when depositing your equipment.
Please contact the local council for details of your local household waste
recycling centers.