Better Homes and Gardens KENDARA BH18-021-199-21 User manual

PB 1
model# BH18-021-199-21
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
rich espresso
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
KENDARA ACCENT TABLE

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
SHELF
BACK PANEL
A
B
C
D
E
DRAWER FRONT
DRAWER LEFT SIDE
DRAWER RIGHT SIDE
DRAWER BACK
DRAWER BOTTOM
F
G
H
I
J
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Bolt
x4
3. Cam
x12
4. Cam Cover
x4
1. Wood Dowel
x14
2. Cam Bolt
x12
6. Lock Washer
x4

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
11. Flat Head Screw
x4
9. Handle Bolt
x2
10. Handle
x1
7. Washer
x4
8. Allen Wrench
x1

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x8 x8 x4
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x4 x4
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
1. Wood
D o w e l
3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x4 x4x4 x1
STEP 3
5. Bolt 6. Lock
Washer
7. Washer 8. Allen
Wrench
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8 9
x2 x4x4 x4
x4
STEP 4
1. Wood
D o w e l
2. Cam Bolt 3. Cam 4. Cam Cover
11. Flat Head
Screw
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
4. Refer to page 5 for instructions on how to use the cam lock system.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x2 x1
STEP 5
9. Handle
Bolt
10. Handle
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
30 lbs. / 13.6 kg.
20 lbs. / 9.1 kg.
15 lbs. / 6.8 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]

PB 1
model# BH18-021-199-21
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
café
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
MESA DE ACENTO
KENDARA
Instrucciones de Ensamble

2
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
REPISA
PANEL POSTERIOR
A
B
C
D
E
CAJÓN FRONTAL
CAJÓN LATERAL IZQUIERDO
CAJÓN LATERAL DERECHO
CAJÓN POSTERIOR
CAJÓN INFERIOR
F
G
H
I
J
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Perno
x4
3. Leva
x12
4. Cubierta del
Tornillo
x4
6. Arandela Fijadora
x4
2. Tornillo de leva
x12
1. Clavija de Madera
x14

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
11. Tornillo de Cabeza
Plana
x4
9. Perno de Agarradera
x2
10. Agarradera
x1
8. Llave Allen
x1
7. Arandela
x4

4 5
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

6
x8 x8 x4
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6 7
x4 x4
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
1. Clavija de
Madera
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

8
x4 x4x4 x1
PASO 3
5. Perno 7. Arandela6. Arandela
Fijadora
8. Llave
Allen
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
3. No sobreapriete los tornillos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

8 9
x2 x4x4 x4
x4
PASO 4
1. Clavija de
Madera
3. Leva2. Tornillo
de Leva
4. Cubierta
del Tornillo
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
3. No sobreapriete los tornillos.
4. Reérase a la página 5 para instrucciones para como usar el sistema de levas.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
11. Tornillo
de Cabeza
Plana