Better Homes and Gardens BH48-084-099-51 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-05-30 Rev. 0001-C
Steele Organizer with Drawers
Stock # BH46-084-099-54
# BH48-084-099-51
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOGUE : Steele Organizer with Drawers
MODEL # BH46-084-099-54 / BH48-084-099-51
MADE IN VIETNAM
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 50 lb. (22.6 kg)
MAXIMUM LOAD 30 lb. (13.6 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 200 lb. (90.7 kg)

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Left Side Panel (Qty. 1) C- Right Side Panel (Qty. 1)
D- Bottom Panel (Qty. 1) E- Upper Fixed Shelf (Qty. 1) F- Lower Fixed Shelf (Qty. 1)
G- Upper Divider Panel (Qty. 2) H- Drawer Divider (Qty. 1) I- Middle Divider Panel (Qty. 2)
J- Bottom Long Support (Qty. 2) K- Bottom Short Support (Qty. 2) L- Back Panel (Qty. 1)
M- Drawer Left Side N- Drawer Right Side O- Drawer Back Panel
(Qty.2) (Qty. 2) (Qty. 2)
P- Drawer Bottom Panel Q- Drawer Bottom Support R- Drawer Front
(Qty.2) (Qty. 2) (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 12+1 extra) (Qty. 22+1 extra) (Qty. 34+1 extra)
(4) M15 x 60 mm Large Wood Dowel (5) M8 x 60 mm Small Wood Dowel (6) M8 x 30 mm Wood Dowel
(Qty. 8+1 extra) (Qty. 16+1 extra) (Qty. 34+1 extra)
(7) M6 x 30 mm Wood Dowel (8) 5/16" x 2-1/4" Bolt (9) Lock Washer
(Qty. 4+1 extra) (Qty. 8+1 extra) (Qty. 8+1 extra)
(10) Flat Washer (11) M4 x 38 mm Screw (12) M4 x 50 mm Screw
(Qty. 8+1 extra) (Qty. 12+1 extra) (Qty. 18+1 extra)
(13) Handle (Qty. 2) (14) Handle Bolt (Qty. 4) (15) Cam Lock Cover (Qty. 4+1 extra)
(16) Plastic Cap (Qty. 4+1 extra) Hex Wrench (1) Glue (Qty. 1)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Hex wrench (provided) and Phillips screwdriver and hammer (not provided).