Better Homes and Gardens Maya BH17-084-099-63 User manual

PB 1
model# BH17-084-099-63
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
MAYA ACCENT CABINET

2
TOP PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
ADJUSTABLE SHELF
BOTTOM PANEL
DOOR
BACK PANEL
A
B
C
D
E
F
G
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer
PARTS LIST
Phillips Head Screwdriver

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Handle Bolt
x2
3. Lock Washer
x8
4. 12mm Pan Head
Screw
x13
1. Wood Dowel
x8
2. M6x32mm Bolt
x8
6. Handle
x1

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
11. 15mm Pan Head
Screw
x2
9. Flat Head Screw
x4
10. Magnet
x1
7. Shelf Pin
x4
8. Allen Wrench
x1
12. Wall Anchor
x1

4 5
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
15. Wall Strap
x1
16. Washer
x10
13. Wall Screw
x1
14. Truss Head Screw
x1

6
x2 x1
STEP 1
11. 15mm
Pan Head
Screw
10. Magnet
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x8 x8 x8
x1
x8
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the bolts go through the pre-drilled holes properly.
3. Do not over tighten bolts.
1. Wood
Dowel
2. M6x32mm
Bolt
3. Lock
Washer
16. Washer
8. Allen
Wrench
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x13
STEP 3
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
4. 12mm Pan
Head Screw
hole for anti-tip strap
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.

8 9
x4
STEP 4
1. Insert shelf supports into desired holes. Dierent holes accommodate dierent shelf heights.
2. Angle shelves to t between the rails and set on top of shelf supports.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
7. Shelf Pin

10
x4 x2x1
STEP 5
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten screws.
3. Make sure the bolts go through the pre-drilled holes properly.
4. Do not over tighten bolts.
9. Flat Head
Screw
6. Handle 5. Handle
Bolt
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x1x1x1x1
x2
12
13
16
14
16
15
STEP 6
14. Truss
Head Screw
13. Wall
Screw
15. Wall
Strap
16. Washer
12. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
25 lbs. / 11.3 kg.
20 lbs. per shelf /
9.1 kg. por repisa
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

PB 1
model# BH17-084-099-63
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
GABINETE DE ACENTO
MAYA
Instrucciones de Ensamble

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Martillo
HERRAMIENTAS NECESARIAS
LISTA DE PARTES
PANEL SUPERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
REPISA AJUSTABLE
PANEL INFERIOR
PUERTA
PANEL POSTERIOR
A
B
C
D
E
F
G
Destornillador Phillips

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Perno de Agarradera
x2
3. Arandela Fijador
x8
4. 12mm Tornillo de
Cabeza de Noria
x13
1. Clavija de Madera
x8
2. M6x32mm Perno
x8
6. Agarradera
x1

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
11. 15mm Tornillo de
Cabeza de Noria
x2
9. Tornillo de Cabeza
Plana
x4
10. Imán
x1
7. Pasador Para Repisa
x4
8. Llave Allen
x1
12. Taquete de Pared
x1

4 5
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
15. Cincha de Pared
x1
16. Arandela
x10
13. Tornillo de Pared
x1
14. Tornillo de Cabeza
Redonda
x1

6
x2 x1
PASO 1
11. 15mm
Tornillo de
Cabeza de
Noria
10. Imán
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6 7
x8 x8 x8
x1
x8
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Cerciórese que los pernos pasen por los agujeros pretaladrados de manera apropiada.
3. No sobreapriete los pernos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
1. Clavija de
Madera
2. M6x32mm
Perno
3. Arandela
Fijador
16. Arandela
8. Llave
Allen

8
x13
PASO 3
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
4. 12mm
Tornillo de
Cabeza de
Noria
agujero para cincha
anti caidas
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
Empiece instalando todos los tornillos a lo
largo de la orilla del panel posterior. Después,
utilzando un cuadro o una cinta métrica,
asegúrese de que el gabinete esté cuadrado.
(si utiliza una cinta métrica, la distancia de una
esquina, en diagonal a la otra esquina debe de
ser la misma en ambas direcciones.) Instalar
los tornillos restantes, comenzando con las
esquinas.