Better Homes and Gardens BH17-084-199-12 User manual

1PB
model# BH17-084-199-12
model# BH17-084-199-11
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
gray
ivory
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
BEDFORD 5 SHELF NARROW
LEANING BOOKCASE

2
RIGHT SIDE UPPER LEG
RIGHT SIDE LOWER LEG
LEFT SIDE UPPER LEG
LEFT SIDE LOWER LEG
TOP SHELF
SHELF [F]
SHELF [G]
SHELF [H]
BOTTOM SHELF
A
B
C
D
E
F
G
H
I
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Short Dowel
x8
3. Binding Screw
x2
4. M6x35mm Bolt
x2
1. Long Dowel
x4
2. M6x25mm Bolt
x8
6. Allen Wrench
x2

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
11. Wall Screw
x1
12. Wall Anchor
x1
7. Mending Plate
x2
8. 15mm Flat Head
Screw
x4
10. 15mm Pan Head
Screw
x8
9. Support Bracket
x2

4 5
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
13. Wall Strap
x1
14. Truss Head Screw
x1
15. Washer
x2

6
x4
STEP 1
1. Carefully tap wooden dowels into place.
1. Long
D o w e l
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x4 x4 x1 x1
x2
4
3
3
STEP 2
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the bolts go through pre-drilled holes properly.
3. Do not over tighten bolts.
5. Short
D o w e l
2. M6x25mm
Bolt
3. Binding
Screw
4. M6x35mm
Bolt
6. Allen
Wrench
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x4 x4 x1 x1
x2
4 3
3
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the bolts go through pre-drilled holes properly.
3. Do not over tighten bolts.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
5. Short
D o w e l
2. M6x25mm
Bolt
3. Binding
Screw
4. M6x35mm
Bolt
6. Allen
Wrench

8 9
x2 x8
STEP 4
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
9. Support
Bracket
10. 15mm
Pan Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x2 x4
STEP 5
1. Make sure the screws go through pre-drilled holes properly.
2. Do not over tighten screws.
7. Mending
Plate
8. 15mm Flat
Head Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x1x1x1x1
!
WARNING
Seriousorfatal crushing injuries can occur
fromfurnituretip-over. To help prevent tip-
over:
-Installtip-overrestraint provided.
-Placeheavyitems on lower shelves and as
farback as possible.
-Placeheaviestitems in the lowest drawers.
-Unlessspecificallydesigned to accommodate,
donot set TVs or other heavy objects on top of
thisproduct.
-Neverallowchildren to climb or hang on drawers,
doors,or shelves.
-Neveropenmore than one drawer at a time.
(OR)
-Donotdefeat or remove the drawer interlock system.
Useoftip-over restraints may only reduce,
butnoteliminate, the risk of tip-over.
Thisisapermanent label. Do not remove.
x2
12
11
14
15
15
13
STEP 6
14. Truss
Head Screw
11. Wall
Screw
13. Wall
Strap
15. Washer
12. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
10 lbs. / 4.8 kg.
15 lbs. / 6.8 kg.
20 lbs. / 9.1 kg.
25 lbs. / 11.3 kg.
30 lbs. / 13.6 kg.
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.

1PB
model# BH17-084-199-12
model# BH17-084-199-11
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
gris
marl
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
LIBRERO ESTRECHO INCLINADO
BEDFORD DE 5 REPISAS
Instrucciones de Ensamble

2
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
PATA SUPERIOR DEL LADO DERECHO
PATA INFERIOR DEL LADO DERECHO
PATA SUPERIOR DEL LADO IZQUERDO
PATA INFERIOR DEL LADO IZQUERDO
REPISA SUPERIOR
REPISA [F]
REPISA [G]
REPISA [H]
REPISA INFERIOR
A
B
C
D
E
F
G
H
I
Martillo Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Clavija Corta de
Madera
x8
3. Tornillo de Sujeción
x2
4. M6x35mm Perno
x2
6. Llava Allen
x2
2. M6x25mm Perno
x8
1. Clavija Largo de
Madera
x4

4
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
11. Tornillo de Pared
x1
12. Taquete de Pared
x1
7. Placa Para Arreglar
x2
8. 15mm Tornillo de
Cabeza de Plana
x4
9. Ménsula de Apoyo
x2
10. 15mm Tornillo de
Cabeza de Noria
x8

4 5
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
13. Cincha de Pared
x1
14. Tornillo de Cabeza
Redonda
x1
15. Arandela
x2

6
x4
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar.
1. Clavija de
Madera
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

6 7
x4 x4 x1 x1
x2
4
3
3
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2.Cerciórese que los pernos tornillos pasen por los agujeros pretaladrados de manera apropiada.
3. No sobreapriete los pernos tornillos.
5. Clavija
Corta de
Madera
2. M6x25mm
Perno
3. Tornillo
de Sujeción
4. M6x35mm
Perno
6. Llava
Allen
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

8
x4 x4 x1 x1
x2
4 3
3
PASO 3
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2.Cerciórese que los pernos tornillos pasen por los agujeros pretaladrados de manera apropiada.
3. No sobreapriete los pernos tornillos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
5. Clavija
Corta de
Madera
2. M6x25mm
Perno
3. Tornillo
de Sujeción
4. M6x35mm
Perno
6. Llava
Allen