Beyond Lighting BY-F600 User manual

BY-F600 600W LED Spot Light
600W LED Spot Light
User manual
P le ase rea d t he ins t r u ction s ca refu ll y before use

2
TABLE OF CONTENTS
1. Safety Instructions ..............................................................2-4
2. Technical Specifications ....................................................4-5
3. LUX Date ..............................................................................6
4. Attention ..............................................................................6
5. Fixture Cleaning ....................................................................7
6. Warning .................................................................................7
statement
The product has well capability and intact packing when leave
factory. All of the user should comply with warning item and manual, any
misuse cause of the damages are not included in our guarantee, and
also can not be responsible for any malfunction & problem owing

3
to ignore the manual.
1. S af ety I nst r uctions
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using
the unit.
 Before operating, ensure that the voltage and frequency of power
supply match the power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order
to avoid electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in a location with adequate ventilation, at
least 50cm from adjacent surfaces. Be sure that no ventilation slots are
blocked.
 Disconnect main power before replacement or servicing.
 Make sure there are no flammable materials close to the unit while operating
as it is fire hazard.
 Use safety cable when fixes this unit. DO NOT handle the unit by taking its
head only, but always by taking its base.
 Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the
temperature is higher than this Unit surface temperature may reach up to 85℃.
DO NOT touch the housing bare-hand during its operation. Turn off the power
and allow about 15 minutes for the unit to cool down before replacing or serving.
 In the event of serious operating problem, stop using the unit
immediately.Never try to repair the unit by yourself. Repairs carried out by
unskilled people can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center. Always use the same type
spare parts.

4
 DO NOT touch any wire during operation as high voltage might be causing
electric shock.
Warning:
 To prevent or reduce the risk of electrical shock or fire, do not expose the unit
to rain or moisture.
 DO NOT open the unit within five minutes after switching off.
 The housing, the lenses, or the ultraviolet filter must be replaced
if they are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure
that the unit is firmly fixed to avoid vibration and slipping while
operating. And make sure that the structure to which you are attaching the
unit is secure and is able to support a weight of 10 times of the unit’s weight.
Also always use a safety cable that can hold 12 times of the weight of the unit
when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people.
2. Technical Specifications
Lamp: LED 600W lamp beads use imported chips life up to 50000 hours
(One-button control the power is off and on ,suggest that the interval should
be more than 10 seconds )
Color Temperature: 3200K / 4500K / 6500K

5
Power Consumption: 700 W
Power Voltage: AC 100-240V, 50/60Hz
Color: Five colors + white (Red, Orange, Yellow, Blue, White)
Aperture: fader adjustment aperture size, clarity manual adjustment
Strobe: 1-11 times/second
Projection distance: 10-50 meters / 10-120 meters
Body size: 810*230*210mm
Body weight: 15KG
Cooling System: Six 8mm thick copper tubes are used to conduct heat
and then heat dissipation through 132 large-area aluminum sheets to ensure
the heat dissipation of LED lamp beads, so that the light fails within the
normal range and the lamp beads lifetime is guaranteed.
Overheating, triggering high pressure protection, using a new type of
aluminum alloy design, arc-shaped body is elegant.
Features
600W LED Spot light uses a high-power LED light source. The color
temperature is ideal and the color rendering index is high. The lamp body is
made of all-aluminum alloy material, with small size, light weight and high
brightness. High-power fan cooling system ensures safe, continuous and
stable operation of the lamps.
The lamps are widely used in stage, theater, film and television and stadiums
to perform close-up follow-up of people and scenery.

6
3.Lux Date
4. Attention
1: When the LED is lit after the power is turned on, it should try to avoid direct
observation of the emitted light. The lamp can be started continuously. After
turning off the power, it needs to wait 10 seconds before restarting.
2: Professional LED light source if you need to replace please consult a
professional technical staff.
Light bulb hot! Avoid electric shock!

7
5. Fixture Cleaning
Before disconnecting the lighter or starting maintenance work, ensure that the
power supply of the light is turned off to maintain the maximum brightness output
of the light, and it can also prolong its service life. It is recommended to use
high-quality professional glass cleaner and to clean it with cloth. Alcohol or
chemical solvents are not allowed under any circumstances. The interior of the
lamp is vacuum-cleaned at least once a year.
6.Warning
Do not disassemble or modify light fixtures
Do not expose the fixture to water or any other kind of liquids and metals
Do not install the lamp in a hot environment
Do not shoot the light beam on flammable materials. The distance between
the light fixture and flammable material should be at least 2 meters.
The distance between the lamp and the surface of the adjacent object should
be at least 0.5 meters.
Do not look directly at the beam of the follower lamp, as it may cause eye
damage
Before opening the chasing light product or want to repair work, please make
sure that the power is off