BG Electrical NX13ADC/IL/A User manual

Accessories
Socket/Chime
1. x2 Fixing Screws
Push Button
1. x2 Fixing Screws
2. x2 Rawl Plugs
3. Double Sided Sticky Pad
4. Push Button Battery (3V CR2032)
Wiring Instructions
1. Power Off
2a. Replacing an existing accessory
2b. New installation
Before commencing work always isolate the power at the consumer unit
/ fuse box.
*Note – If your installation uses a four-lug metal mounting box, remove the
top and bottom lugs or bend fully back.
1. Unscrew the accessory from the wall/mounting box.
2. Note the cable connections:
The illustration shows 1 wire of each colour connected to each terminal.
There should be an additional connection between the mounting box earth
terminal and the accessory earth terminal.
3. Unscrew each terminal to release the wire.
1. Install mounting box (metal or moulded) for either flush or surface
mounting, ensuring appropriate size of product.
2. Select the most suitable entry point of the mounting box (knock-out) and
route the cables through.
If a metal box is used, a cable grommet should be fitted to the entry point.
3. Cables should be prepared so a sufficient conductor length reaches the
terminals.
Strip the ends of the individual conductors leaving an adequate length bare
to enter terminals.
3. Connection (See diagram)
1. Line up the new accessory to mounting box and take note of where each
terminal is located.
2. Connect each wire to the matching terminal.
An earth connection should always be made between the mounting box
earth terminal and the accessory earth terminal, where fitted.
All bare earth wires must be sheathed with green/yellow sleeving.
When connecting the new accessory ensure that only the bare end of the
wire enters the terminal and no bare wires are visible.
3. Tighten terminal screws securely. (Do not over tighten)
4. This socket is fitted with two linked terminals to provide a dual earth fa-
cility. This is for use in “clean” installations where additional earth capacity
is required to comply with Regulation 607 IEE Wiring Regulations.
4. Complete Installation & Test
1. Carefully position the accessory into the mounting box, ensuring that no
wires are trapped between the plate and the wall and secure with screws
(do not over tighten) then insert screw covers (optional).
2. Once the installation has been completed correctly, replace the fuse/
reset MCB (trip), switch the power back on at the consumer unit and test.
Wiring Accessories
13A Socket with Door Chime
NX13ADC/IL/A Safety Warning
3. Offer the push button backing up to the wall and drill holes. If fitting to
masonry, use a 6mm drill bit, as per the depressions and securing by
using the supplied rawl plugs and screws. If fitting directly to the
woodwork, use a 2mm drill bit and screw directly into frame or use the
provided sticky pad.
4. Pull plastic tab from under battery to power the push button.
Installation
1. First, identify a suitable area for the push button to be positioned.
Ideally, this should be sheltered from rain or excess heat.
It would be recommended that the button is fitted to the door frame itself,
so you are able to screw directly into the woodwork, making the
installation simple.
2. Place a small flathead screwdriver into the slotted hole and gently
twist to remove push button back.
23
FUNCTIONAL EARTH
NEUTRAL
EARTH
LIVE
NEUTRAL
EARTH
LIVE
TO MOUNTING BOX
EARTH TERMINAL
LE
N
For your safety, this product must be installed in accordance with local
Building Regulations.If in any doubt, or where required by the law, con-
sult a competent person who is registered with an electrical self-certifi-
cation scheme. Further information is available online or from your Local
Authority.
Please read carefully and use in accordance with these safety wiring
instructions. Before commencing any electrical work ensure the supply is
switched off at the mains. Either by switching off the consumer unit or by
removing the appropriate fuse or turning off MCB (trip). Wiring should be in
accordance with the latest edition of the IET regulations (BS 7671).
To prevent fire hazard always use cable of the correct rating & type for the
application.
Warning do not exceed the load rating of this device as stated on the rear
of the product.
Wire Identification – Twin & Earth Cable
Note - As from 1st April 2004 new colour codes for hard wire installations
were introduced.
EARTH = Green/Yellow Sleeving
NEUTRAL = Black (pre Apr 04) / Blue (after Apr 04)
LIVE = Red (pre Apr 04) / Brown (after Apr 04)
5. Refit the push button to the secured backing by offering up the button of
the push button and gently pushing back together.
45
fit first
press down

Batch Code explanation
yyWxx Manufacturing date code, year of manufacture (yy) and week of
manufacture (Wxx)
Environmental Protection
This symbol is known as the “Crossed-out Wheelie Bin
Symbol”. When this symbol is marked on a product or battery,
it means that it should not be disposed of with your general
household waste. Some chemicals contained within electrical/
electronic products or batteries can be harmful to health
and the environment. Only dispose of electrical/electronic/
battery items in separate collection schemes, which cater for
the recovery and recycling of materials contained within. Your
co-operation is vital to ensure the success of these schemes
and for the protection of the environment.
Address/Helpline
If you have further technical assistance you can get in touch with our
Technical Helpline on:
[phone]
[e-mail]
(EU) Luceco SE
C/ Bobinadora 1-5
08302 Mataró
SPAIN
Luceco PLC
Stafford Park 1
Telford TF3 3BD
ENGLAND
Setup Door Chime EU Declaration of Conformity
Indoor use only
Door Chime Socket only
This product does not consist of any serviceable parts and should not be
repaired. The device should not be operated by persons who have a lack of
experience or knowledge in using such products. People who have a
reduced physical, sensory or mental capability should be supervised or
given instruction when operating. Children should be supervised, so that
they do not play with the device.
IMPORTANT
Technical Information
Push Button Battery : 1 x 3V CR2032
Push Button : IP44
Melody Count : 6
Sound Level : 80dB
Range : 100M (open air)
Wall Box Depth : 25mm
•
•
•
•
•
•
Unique Code Selection
The door chime and push button will be paired straight out of the box, with 1 out
of 1 million unique codes to prevent interference with another door chime. If
the door chime does not sound, please refer to the 'Pairing Additional Push
Buttons & Door Chimes' section.
Chime Selection
Volume Selection
Pairing Additional Push Buttons & Door Chimes
Reset Door Chime
Maximum distance is based on an open area environment. Any walls,
doors or ceilings may reduce the operating range.
Door chime is to be used indoors only.
Door Chime Not Working?
Single press the melody button on the left of the door chime socket to
filter through the six different options – 4 x ‘Ding-dong’ and 2 x ‘Westminster’
chimes.
1. Single press the right side volume selection button to filter through the
four different volumes settings. Options include – No sound, low, mid
and high volume.
2. The LED flasher will always flash for 10 seconds on each press of the button.
Press and hold the Melody button until the LED illuminates, then release.
Push the button on the ‘Push Button’, once the door chime socket will ring,
then the units are paired. Repeat the process to pair additional push buttons
to the door chime.
(A maximum of 16 push buttons can be paired).
Press and hold the melody button for 10 seconds or until you hear a triple
‘beep’ to reset the door chime.
1. Ensure the battery in the push button is new..
2. Objects and materials, such as walls, doors, ceilings and furniture, are
blocking the signal. Try moving the chime closer to the push button.
3. Wireless interference can be caused by external wireless devices, such
as alarms and adaptors. It is recommend not to plug-in such devices in the
door chime socket, or have in the close vicinity.
4. Door chime and push button are not paired – please refer to the ‘Pairing
Additional Push Buttons’ section.
5. Ensure wired connections are made good, MCB is on and power is being
made to the socket.
Chime Selection
Volume Selection
EU Declaration of Conformity
Applicant: Luceco PLC
Address: Luceco Distribution Centre, Stafford Park 1, Telford Shropshire,
United Kingdom
(EU) Luceco SEC/Bobinadora 1-5 08302 Mataró SPAIN
Description: 13A Socket with Door Chime
Model: 822BELL
We (Luceco PLC) declare under our sole responsibility that the products
above are in conformity with the essential requirements of the following:
Signed for and on behalf of: David Cleaver
Senior Product Manager
Place of Issue: Stafford Park 1,Telford Shropshire, United Kingdom
Date of Issue: 16/Mar/2020
This product belongs to receiver category 2
: Caution
Push Button
This product contains a coin/button cell battery and if ingested can cause
severe chemical burns. If the battery has been ingested, please seek
medical advice immediately. In just 2 hours a digested battery can lead
to death. Keep new and used batteries away from children. If the battery
compartment does not close securely, please stop using the product.
Radio Equipment Directive (RED)
2014/53/EU
Article 3.1(a)Health
EN62479:2010
EU Directives Conformas to
2011/65/EU and its amendment
2015/863/EU(ROHS)
ROHS 2011/65/EU and its amendment
2015/863/EU
2009/125/EC ERP ERP:
EN 50564:2011
Article 3.2 Radio:
EN 300 220-1 V3.1.1 (2017-02)
EN 300 220 2 V3.1.1 (2017-02)
Article 3.1(b)EMC:
Draft EN 301 489-1 V2.2.0 (2017-03)
EN 301 489-3 V2.1.1 (2019-03)
Article 3.1(a)Safety:
EN62368-1:2014+A11:2017