BGS technic 9259 User manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
Art. 9259
Cordless Polishing Machine
IMPORTANT: Please read these instructions carefully.
Note the safe operational requirements, warnings, and cautions.
Use this product correctly, and with care for the purpose for which it is intended.
Failure to do so may cause damage and / or personal injury and will invalidate the warranty.
1. INTRODUCTION
This powerful and compact cordless polishing machine is made for polishing of small surfaces. This
well-balanced tool has a speed setting and comes with battery and charger.
2. SPECIFICATION
No-Load Speed: approx. 1500 - 3000 rpm (stepless adjustable)
Pad diameter: 100 mm
Machine weight: approx. 820 g
Noise level: LpA: 71 dB(A) / KpA: 3 dB
LwA: 82 dB(A) / KwA: 3 dB
Vibration: ah= 2.68 m/s²
K= 1.5 m/s²
Battery pack: 10,8 V Li-ion / 1.3Ah
Mains charger: Input: 100 - 240 VAC / 50 – 60 Hz / 30 W
Shaft thread: M10

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
3. SAFETY INSTRUCTIONS
3.1. GENERAL SAFETY
- Follow all workshop safety rules, regulations and conditions when using the cordless tool.
- Remove the battery pack from the cordless tool before servicing or performing any maintenance.
- Maintain the cordless tool and battery pack in good condition. Check moving parts for alignment
on a regular basis.
- Replace or repair damaged parts. Use an authorised service agent and recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
- Ensure the cordless tool is ‘off’ before installing the battery pack.
- Keep the cordless tool, battery pack and charger clean for optimum performance.
- Keep the work area clean and tidy and free from unrelated materials. Ensure that there is
adequate lighting.
- Ensure that battery pack is correctly inserted into the cordless tool and latched in place before
operating cordless tool.
- Avoid unintentional starting.
- Wear approved safety eye/face shield, ear defenders and hand protection.
- Remove ill-fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long
hair.
- Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
- Keep children and unauthorised persons away from the work area.
- DO NOT operate the cordless tool if any parts are missing as this may cause failure and personal
injury.
- DO NOT use the cordless tool unless you have been instructed in its use by a qualified person.
- DO NOT operate the cordless tool where there are solvent fumes or flammable gases, liquids or
solids.
- DO NOT use the cordless tool for a task it is not designed to perform.
- DO NOT operate the cordless tool when you are tired or under the influence of alcohol, drugs or
intoxicating medication.
- DO NOT get the cordless tool or battery charger wet or use in damp or wet locations.
- Keep cordless tool and charger in a safe, dry, childproof area where the temperature will not
exceed 40°C (104°F).
3.2 BATTERY SAFETY INSTRUCTIONS
WARNING! The battery pack contains nickel-cadmium, which is dangerous. It must therefore be
handled with care.
- Charge the battery pack prior to first use. The battery pack will have been shipped in a low charge
state.
- Use only the charger provided to charge the battery pack.
- DO NOT charge the battery pack when room temperature is below 10°C (50°F) or above 40°C
(104°F).
- DO NOT attempt recharging the pack by means of an engine generator or a DC power source.
- DO NOT short-circuit the battery pack by touching both terminals at the same time with a metal
object, or your fingers etc.
- DO NOT store battery pack (or cordless tool) in locations where the temperature may exceed
40°C (104°F) e.g. in outside sheds, above heaters etc.
- WARNING! Dispose of spent battery pack correctly as it contains nickel-cadmium.
- DANGER! DO NOT attempt to disassemble the battery pack. For safety and environmental
reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle according to
local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with
battery liquid seek immediate medical attention.
- Make sure that the speed controller is in position 0before connect the battery.

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
3.3. MAINS POWER ELECTRICAL SAFETY (In relation to the battery charger)
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with
the following:
- Ensure that the insulation on cables is safe before connecting it to the power supply.
- Do not pull or carry the appliance by the power cable.
- Do not use worn or damage cables, plugs or connectors. Immediately have any faulty item
repaired or replaced by a qualified electrician.
3.4. BATTERY CHARGER SAFETY INSTRUCTIONS
- WARNING! Do not attempt to charge any battery other than that supplied for the cordless tool.
Other types of batteries may explode!
- Disconnect the charger from the mains supply when not in use.
- Do not charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
- Do not expose the charger to damp or wet conditions.
- Do not pull or carry the charger by the power lead.
- Do not operate the charger if it has been dropped, or has received a sharp knock, or is damaged.
Take the charger to an authorised agent for repair or obtain a replacement.
- Do not dismantle the charger as this may cause damage and personal injury and will invalidate
the warranty.
- Do not insert foreign objects or material into the hole reserved for the battery pack.
- Do not recharge a second battery pack immediately after charging the first. Consecutive charging
will overheat the charger. Allow the unit to cool for 15 minutes before charging the next pack.
- Do not attempt to connect two chargers together.
- Store the charger in a same manner as the battery pack.
4. OPERATING INSTRUCTIONS
4.1. PARTS DESCRIPTION
1
Shaft Lock
2
On / Off / Speed Controller
3
10,8V Battery
4
Battery Retaining Clip
5
Velcro Adapter
CHARGER
No LED lights
Charger not connected
to main voltage
Green LED lights
Charger is connected
to main voltage
Red LED lights
Battery is charging
Green LED lights
Battery has charged
fig.2
fig.1 fig.3 fig.4
fig. 1

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
4.2. CHARGING THE BATTERY PACK
4.2.1. Remove the battery pack from the wrench, by depressing the two side retaining clips (fig.1).
WARNING! Do not touch metal terminals.
4.2.2. Place the cordless tool to side and take the battery charger.
4.2.3. The battery pack and charger have the positive (+) and negative (-) terminals marked. Align
the correct terminals and insert the battery into slot (fig.3 & 4).
Note: The battery pack is designed so that it will only enter the charger unit the correct way.
When placed in the charger, a very slight downward pressure will seat the pack firmly into the
power terminals.
4.2.4. Connect the charger to mains supply; red LED lights (fig.3).
Charging begins.
4.2.5. When charging is complete, the red LED goes out and the green LED lights (fig.4). The battery
is now ready to use. Note: When new, the battery pack will have been shipped in a low charge
state. It will take longer to charge initially, and several subsequent charges may also take a
little longer than when the battery pack reaches its optimum performance. Normal charging
time is approximately 1 hour.
4.2.6. After removing the battery, disconnect the charger from the mains supply and store it for
safekeeping in a dry place.
4.2.7. Make sure that the speed controller is in position 0before connect the battery to polishing
machine.
4.3. USING POLISHING MACHINE
4.3.1. Warning: Fix the Velcro adapter (fig.1.5.) before first use. Press the shaft lock (Fig.1.1.) and
rotate the Velcro adapter until the lock is latched. Now the Velcro adapter can be fixed by
turning clockwise. It is enough to tighten the Velcro adapter by hand. Release the shaft lock
and check whether the Velcro adapter can rotate freely.
4.3.2. Fit the battery pack to the cordless tool by aligning the tongue on the battery with the groove in
the housing and slide it into place. Ensure that the battery pack is firmly located, you will hear
an audible click when it has locked into position.
4.3.3. Select the required pad and insert it centered on the Velcro adapter.
4.3.4. Set the desired speed by turning the speed controller (fig.1.2).
4.3.5. To remove the Velcro adapter (fig.1.5.), press the shaft lock (fig.1.1) and turn it counter
clockwise.
5. MAINTENANCE
Keep the outer case of the cordless tool clean and free from grease.
Do not wash with water or use solvents or abrasives. Use a damp cloth.
For any other service or maintenance, contact your authorised service agent.
6. DISPOSAL
Never disposal the batteries or cordless tool with your domestic waste.
Collect worn out batteries or electrical appliances and recycle them
at your local collecting point or give it to your dealer.

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
CE-Erklärung
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
EU-KONFORMITÄTSERKLÄRUNG
EC DECLARATION OF CONFORMITY
DÉCLARATION„CE“ DECONFORMITE
DECLARATION DE CONFORMIDAD UE
Wir erklären in alleiniger Verantwortung, dass die Bauart des Produktes:
We declare that the following designated product:
Nous déclarons sous propre responsabilité que ce produit:
Declaramos bajo nuestra sola responsabilidad que este producto:
folgenden einschlägigen Bestimmungen entspricht:
complies with the requirements of the:
est en conformité avec les réglementations ci-dessous:
esta conforme a las normas:
Angewandte Normen:

Norme appliquée:
Normas aplicadas:
ppa.
Frank Schottke, Prokurist
BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen
Wermelskirchen, den
Akku-Polierer (BGS Art. 9259)
Cordless polisher
Polisseuse sans fil
Batería - Pulidora
Machinery Directive 2006/42/EU
EMC Directive 2014/30/EU
EN 60745-1:2009+A11:2010
EN 60745-2-3:2011+A2:13+A11:14
EK9-BE-77 (V3):2014 EK9-BE-88:2014
EK9-BE-89:2014 EK9-BE-91:2015
EN 55014-1:2006/+A1:2009/+A2:2011
EN 55014-2:1997/+A1:2001/+A2:2008
EN 61000-3-2:2014 EN 61000-3-3:2013
Certificate No.: 161000561HZH-V1/QM-5001
Certificate Charger: 160302169SHA-V1/JLH2012601500G
Test Report No.: 160302169SHA-001 / Charger: 160302169SHA-001
08.11.2016