Bianco di Puro Volto N User manual

1
EN
DESCRIPTION
TAMPER T42S
18
17
16
Battery
Display
Cover cap
Washer
Handle
Temperature
sensor
19
20
21
Powercord
15
Lid
Bladeunit
Blademount
Blade coupling
Jar locking
Speedlevel selection,
Pulse-Button
Motorbase
Air diffuser
Rubber bumpers
Measuring cup
1
2
Silicone seal
Jar
4
5
6
12
13
10
7
Program selection,
On/Off Button
Jar mat
8
11
9
14
3

EN
2
CONTENTS
Description...................................................................................................................................................1
Contents ......................................................................................................................................................2
Introduction ..................................................................................................................................................4
Information about this User Manual ................................................................................................................5
Safety Functions ...........................................................................................................................................5
Safety Precautions ........................................................................................................................................6
Safety Precautions .......................................................................................................................................7
Operating Notes ...........................................................................................................................................8
Unpacking....................................................................................................................................................9
Scope of delivery ..........................................................................................................................................9
Start-up .......................................................................................................................................................9
Requirements of the Installation Location .......................................................................................................10
Electrical Connection ....................................................................................................................................10
Operating Volto | N........................................................................................................................................11
Measuring Cup, Lid and Seal Ring .................................................................................................................13
Operating element ........................................................................................................................................14
Operating Program Buttons ...........................................................................................................................15
Operating Volto | N preset programs ..............................................................................................................16
Program description......................................................................................................................................17
Manual mode Volto | N ..................................................................................................................................18
Operating the Tamper T42S...........................................................................................................................19
Safety Guideline for Cleaning .........................................................................................................................20
Cleaning of the Jar (incl. Lid), Motor Base and tamper.....................................................................................21
Instructions for general preparation................................................................................................................22
Technical Data ..............................................................................................................................................33
Disposal Note ...............................................................................................................................................34
Disposal of used batteries .............................................................................................................................34
Contact and Customer Service ......................................................................................................................35
Warranty Conditions......................................................................................................................................36

3
EN
RECIPES
Introduction to our recipes.............................................................................................................................23
Fruit-Smoothies ............................................................................................................................................24
Grinding .......................................................................................................................................................25
Cereal milk ...................................................................................................................................................26
Cashew milk, Almond milk and Hemp milk......................................................................................................27
Green Smoothies ..........................................................................................................................................28
Sauces.........................................................................................................................................................29
Warm Soup ..................................................................................................................................................30
Ice Cream.....................................................................................................................................................31
Frozen Yoghurt .............................................................................................................................................32

EN
4
The Volto | N is a high-performance mixer which you can use to blend
(almost) everything. With a powerful motor, the blades in the mixing
container rotates at 1,500 to 32,000 revolutions per miunute.
The Volto | N is perfect for the preparation of green smoothies, where
valuable vital nutritions from green vegetables and leafy greens are
optimally blended by rapid and thorough shredding. The result: a super-
creamy, viscous smoothie that is pleasant to drink and provides your body
with a wealth of essential nutrients.
Because the blender makes this preparation so easy, green smoothies are
right on trend: Many people supplement their diet or replace their breakfast
or another meal completely with one of the green power drinks.
Just as easily, the Volto | N can be used with other ingredients for classic
smoothies made from fruits and vegetables. It can also be used to mixes
warm soups.
Fans of vegan cuisine can use the Volto | N to make herbal milk alternatives
such as: soy, rice or almond milk yourself.
INTRODUCTION

5
EN
INFORMATION ABOUT THIS USER MANUAL
SAFETY FUNCTIONS
This user manual is part of your Volto | N and provides important information for start-up, safety, proper use and
maintenance of your device. The user manual must always be available with the device.
It must be read by every user who deals with start-up, operation, cleaning and maintenance of your Volto | N.
Your Volto | N has three safety functions to protect third parties and the device from being damaged.
Overheating protection
The motor of your Volto | N is equipped with a temperature control. If the motor or the blades turn too slowly due to
too solid foods or too little fluid, there is a danger of overheating. If the motor should switch off for that reason, the
overheating protection of your Volto | N is activated. Let your Volto | N cool off for about 45 minutes in a well-ventilated
area, afterwards you can use your Volto | N as normal.
Overload protection
This protects the motor in case the blades in the jar are not able to rotate because of a blockage (forgotten items in the
blender, such as spoons.)
Automatic jar detection
The sensor for the jar detects when the jar has been set up correctly. If the jar is not, or has not been placed correctly,
your Volto | N will not turn on. Never attempt to bypass the sensor to protect yourself and third parties from injuries,
and to prevent damage to the device.

EN
6
SAFETY PRECAUTIONS
Please observe the following safety precautions for the safe use of your blender:
• Check the Volto | N before the first use for any externally visible damage of the jar, housing, power cable, and
power plug. Do not operate if the device or the power cable is damaged.
• Do not use if the power cable or power plus is damaged. A damaged cord can cause electric shock or
a short circuit.
• Make sure the power plug is properly inserted when operating the blender. Otherwise this could lead to electric
shock or short circuit.
• If the power cable is damaged, the blender must not be used.
• In case of damage to the power cable, repairs should only be made by the manufacturer or service agent in order
to avoid hazards.
• To avoide electric shock, never immerse the motor base in water or other liquids.
• If water or another fluid has entered the motor base, contact your service as soon as possible. Disconnect the
power plug and do not operate the device.
• Never place the power cable orthe power plug in water or other fluids, never wipe the power plug with a wet or
moist cloth. Never touch the power plug with wet or moist hands. Never pull the plug from the socket with wet or
moist hands.
• Repairs within the warranty period must only be carried out by customer service. Incorrect repairs can lead to
considerable hazards for the user, and will void the warranty.
• Defective parts must only be replaced with original parts, because only original parts ensure that all safety
requirements are met.
• Never put your hands in jar during operation. It will cause injuries.
• To remove air bubbles or blockages in the jar use only the supplied tamper.

7
EN
SAFETY PRECAUTIONS
• Use only the supplied jar with the Volto | N, or compatible range of jars.
• Fill the jar only to the maximum level on mark.
• During mixing, the content must not exceed the maximum level.
• Children and frail persons must always be supervised by a person responsible for their safety,
when using the Volto | N.
• Always store the device and the mixer attachment in a place inaccessible to children.
• Always disconnect the power cord by pulling the plug from the power socket not by pulling the power cord.
• Make sure that the power cable is not caught anywhere, causing the device to fall and injuring people.
• Operate the device only with a filled jar.
• Do not operate the device in direct sunlight or near other heat sources.
• During operation, make sure that the lid incl. seal ring and measuring cup correctly close the jar.
• Always disconnect the power cable when cleaning moving parts.
• Pay attention to the blade unit during cleaning, the sharp blades may cause injury.
• Do not try to dismantle the blades from the jar, they are permanently fixed to the device.
• Never leave the device without supervision during operation.
• This appliance shall not be used by children.
• Children shall not play with the appliance.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and
if they understand the hazards involved.
• Make sure that the power cord does not block the air outlet (see Figure 13 on page 1).

EN
8
OPERATING NOTES
If you want to prepare sauces, soups or nut milk, add the ingredients in 2 to 3 steps, depending
on their hardness. The content should not be too little, but also not too much. Too many
ingredients in one process may lead to overheating and automatic shutdown of the motor.
In that case, please wait until the device cools down as described above (also see chapter “Overheating protection”
on page 5).
Always keep the lid closed during the operation of your Volto | N. This privents any scalding or splashes of hot foods.
When preparing hot liquids, make especially sure that the lid is closed well and your Volto | N is standing securely.
It is advisable to first start at low speed and increase gradually. Alternatively you can use the Pulse mode or one of
the preset program (see chapter ).
Never put your hands into the jar during operation. Do not dip any objects into the jar during operation, otherwise
the motor, blades and other parts of the device can be damages. Only use the supplied tamper T42S through the lid
opening (Fig. [2], page 1), since it cannot contact the blades through the opening for the measuring cup. For further
information see chapter “Operating the Tamper T42S” on page 19. Always pour liquids and soft ingredients first
into the jar before the harder ingredients, such as ice cubes, carrots, etc.
If the chosen program or the manual mode is finished, please wait until the blades are fully stopped before removal
of the jar, otherwise the connection can be damaged.
If a burning smell rises from the motor block, stop the device immediately and disconnect the power supply. The
smell can result from abrasion of the rubber bearing mounted incorrectly. Please contact your customer service
immediately.
When preparing with thick and sticky ingredients such as dough, it is possible that the motor and the blades turn
idle. This is because bubble has formed in the ingredients. Pause the mixing process with the pause button and
remove the measuring cup from the jar lid. This opening allows you to remove the air bubble by the supplied stamper.
Reinsert the measuring cup and continue with the preparation.
Always hold the jar with one hand when using the tamper!

9
EN
UNPACKING
SCOPE OF DELIVERY
START-UP
To unpack yo u r Volto | N:
• Remove the motor base and all accessories from the carton.
• Remove all packing material from the motor base and the accessories
• Keep the packaging material during the warranty period, in order to pack appropriately for warranty service.
Please note the labels on the motor base and tamper
• Do not remove any stickers. They are attached for safety reasons and are required for warranty service.
• Please do not remove the stickers on the handle of the tamper. The safe use of the tamper is shown.
Your high-performance blenderr is delivered with the following components:
• Motor base Volto | N
• Mix container Cube+
• Lid (inc. silicon seal) with removable measuring cup
• Tamper T42S (with patented temperature display)
• This user manual
ATTENTION
During the start-up of the blender personal injury or property damage can occur.
• Observe the safety precautions on page 6.
• Packing materials must not be used to play with, because there is danger of suffocation.
• Make sure that you have closed the jar lid (with att. Silicone seal and measuring cup) before mixing.

EN
10
REQUIREMENTS OF THE INSTALLATION LOCATION
ELECTRICAL CONNECTION
For the safe and faultless operation of your Volto | N, the installation location must
fulfil the following condition:
• The device must be placed on a level, flat, solid and nonslip surface that ensures the load capacity.
• Take care that the device cannot fall over.
• Do not place a cloth under the device.
• Choose the installation location so that children cannot play with the device or reach into it and
cannot pull the power cord of the device.
• Place the unit only inside and do not operate it outdoors.
• Do not place the device in the immediate vicinity of other heat sources (oven, etc.).
• Do not place the engine block in direct sunlight.
• Make sure that the power cord does not block the air outlet (see Figure 13 on page 1).
For the safe and faultless operation of the device, the following points for the
electrical connection must be observed:
• Connect your Volto | N to a power socket with the correct electric specifications. You can find them on the type
plate at the back side of the device and in the chapter „Technical Data“ on page 32. Make sure that the power plug
is properly inserted into the power socket.
• The electrical safety can only be ensured, if it is connected to a properly installed protective earth system.
• The manufacturer takes no responsibility for damages caused by a missing or disconnected protective earth.
• Make sure that the power cable is undamaged and does not pass over hot surfaces or sharp edges.
• The power cable must not be pulled tight or under tension.
• Make sure that the power plug is properly inserted into the power socket, a loose plug can lead to overheating of
the device or electric shock.

11
EN
OPERATING VOLTO | N
Energy Saving Mode1
For use of your Volto | N it is necessary that the jar is placed correctly on the motor block and the power cable
connected to a suitable power supply. The On/Off button flashes red. Without the attached jar your Volto | N cannot
be switched on for safety reasons.
Activating Standby Mode / Start up
Place the jar on the motor block and tap the On / Off button. Now the available options for each function mode light up
on the control element. In standby mode, the program icons, on / off button, and pulse button will light up. The display
shows 00 00:00.
iPMS (integrated Power Management System) (automatic power in the speed level 1-5):
During the mixing of solid foods (eg. dough, nut mousse) the automatic power checks continuously the motor power
and automatically readjusts it when necessary. That way the optimal processing of the mixing content is ensured.
Due to this automatic power a dynamic perception of speed can occur during the preparation of softer foods in the
speed settings 1-5. This does is not a defect, but caused by the automatic power.
Your Volto | N automatically changes to Energy-Saving-Mode after 3 minutes of inactivity.
1 Power consumption in Energy Saving Mode: 0.41 Watt, Power consumption w/o Jar: 0.39 Watt

EN
12
Cube+. The Jar.
The shape of the jar and the blades are a perfect duo for preparing green smoothies, fruit smoothies, crushed ice,
desserts, hot soups and much more.
The Cube+ jar has the patented SmartCorner technology which allows a perfect swirling in the container during the
mixing process. The mix is continuously fed to the rotating blade during the mixing process.
For a perfect mix, we recommend a filling volume of 500 - 1,500 ml.
Cube+. The Blades.
The unique shape of the blades has been specially designed for the Cube + jar. Due to its special blade mold and the
long knife blades, the mix is optimally shredded and allows maximum splitting of the cell walls. The advantage of the
longer knife blades is that the outer edge reaches an exceptionally high rotational speed. As a result, a better result is
achieved in all preparations.
Vacuum pump *. Air out, Freshness in.
The Cube + is compatible with the vacuum pump with its built in silicone seal on the top
of the jar.
With the vacuum pump, you can create a vacuum in a filled jar quickly. This
prevents the oxidation of your food during the mixing process. You can expect
richer colors and a whole new taste experience.
* not included, please order separately.
JAR CUBE+

13
EN
MEASURING CUP, LID AND SEAL RING
Place the measuring cup (Fig. [1], page1) in the opening of the lid (Fig. [2], page 1) and twist it tight towards the right.
Now, place the lid firmly on the jar. Turn the measuring cup to the left to take it off, and lift it off the lid.
You can remove the seal ring from the lid for easy cleaning. Please take care, that the seal ring is placed in the lid after
cleaning.

EN
14
OPERATING ELEMENT
Run-time indicator
Progam symbols
Speedlevel indicator
PROGRAM SPEED
4
1
23

15
EN
OPERATING PROGRAM BUTTONS
Jogdial for presetprogram selection
Turn the program switch (left rotary control) to the desired program. The currently selected program is shown
by flashing of the respective symbol. The motor will stop automatically after the program is complete. For an
overview see chapter “Program description” on page 17.
On/Off Button
This button starts all programs, which have first been chosen with the program switch. During the start of
the program this button is lit white. By pressing the On/Off button again the program is ended prematurely.
Pulse Button / Pulse Mode
With this button your Volto | N starts with the lowest speed and goes up to level 10 within 2 seconds. During
operation in Pulse mode you must keep this button pressed. The blender stops automatically when the button
is released. The display shows the speed and the elapsed time indicated in the active Pulse mode.
Jogidal for speed level selection
Use the speed control switch in manual mode. The speed can be set from level 1 to level 10.
The display shows the levels as follows:
01, 02, 03, 04, 05, 06, 07, 08, 09, 10
1
2
3
4

EN
16
OPERATING VOLTO | N PRESET PROGRAMS
Start up a preset program
Select your desired program by tapping your prefered program button. The chosen program is shown by flashing of the
symbol. By tap the On/Off button the chosen programme will start. At the same time, the remaining time is shown at
the display. Upon completion the program your Volto | N stops automatically.
Aborting an Automatic Programme
To abort the active programme, tap the On/Off button.
Remove the mixing container only when the blades do not rotate anymore.
Symbol Program Program description Run time Display
Fruit Smoothies
Level 10 for 8 seconds, then 2 seconds stop.
In total 3 repetitions.
Speed gradually increase when program starts.
00:30 Sec. Remaining time,
speed level
Grinding
Level 5 for 5 seconds, level 8 for 2 seconds,
then 1 second stop. In total 10 repetitions.
Speed gradually increase when program starts.
00:35 Sec. Remaining time,
speed level
Cereal Milk
Speeds up to level 5 in 5 seconds,
level 5 for 25 seconds, then level 8 for 30 seconds.
Level 10 by the end of the program.
Speed gradually increase when program starts.
06:00 Min. Remaining time,
speed level
Green
Smoothies
Level 10 for 20 seconds, 2 seconds stop. Level 6 for
10 seconds, 2 second stop. Level 10 for 40 seconds, 2
seconds stop. Level 6 for 10 seconds.
Speed gradually increase when program starts.
01:26 Min. Remaining time,
speed level
Sauce
Level 8 for 2 second, then 1 second stop.
In total 5 repetitions. Then Level 10 for 45 seconds.
Sanfter Geschwindigkeitsanstieg bei Programmstart
01:00 Min. Remaining time,
speed level
Warm Soups
Level 7 for 7 seconds, the level 10 for 3 seconds.
Level 10 by the end of the program.
Speed gradually increase when program starts.
04:20 Min. Remaining time,
speed level
Ice Cream
Level 10 for 20 seconds, then 2 seconds stop, Level 10 for
20 seconds, then 2 seconds stop, Level 10 for 5 seconds.
Speed gradually increase when program starts.
00:49 Sec. Remaining time,
speed level
Frozen Yoghurt
Level 8 for 13 seconds, 2 seconds stop. Level 10 for
10 seconds, 2 seconds stop. Level 8 for 13 seconds, 2
seconds stop. Level 10 for 10 seconds, 2 seconds stop.
Level 5 for 10 seconds.
Speed gradually increase when program starts.
01:04 Min. Remaining time,
speed level

17
EN
PROGRAM DESCRIPTION
Fruit Smoothies
This is to prepare pure fruit smoothies, which do not contain leaf green or wild herbs.
Grinding
This programme is optimal for grinding of dry ingredients such as nuts, poppy seeds, cereals and up to coffee beans.
Recommend using the wet-dry jar square1(also made of Tritan plastic and BPA-free).
1 This is available as an accessory.
Cereal Milk
Use the cereal milk program to prepare homemade rice milk, soy milk, etc. Some recipes you will find on page 27.
Green Smoothies
This programme was creates especially for the preparation of green smoothies and is set up so the green leaves are
finely macerated and the essential elements such as the chlorophyll are optimally unlocked.
Sauce
Make delicious sauces in no time! For instance tomato and basil pesto. You can also prepare delicious nut, cashew
and almond milk with this program.
Warm Soups
We use warmth from the frictional energy during mixing to create delicious warm soups. By 4:20 minutes, you can heat
the content to nearly 42°C (approximate value - depending on the filling quantity and storage temperature of the foods).
This makes it possible to prepare a simple tasty soup in raw food quality. To monitor the temperature in the jar (e.g.
raw food) use the supplied tamper T42S with patented temperature display. For more information see “Operating the
Tamper T42S” on page 19.
Ice Cream
The motor is powerful enough to also mince frozen ingredients and mix them to a creamy consistency.
Frozen Yoghurt
Ice cold drinks or frozen yoghurts are no problem, this settings takes care of that in an instant. This programme blend
frozen ingredients and mixes them with the added fluid without interval.
Note For more recipe ideas see chapter “Introduction to our recipes” on page 23

EN
18
MANUAL MODE VOLTO | N
Manual Mode
In addition to the 8 preset programs, you can operate the Volto | N in manual mode. The mixer must be in the standby
mode (the program icons, the On / Off button and Pulse button lights in white). By turning the Speed control switch (see
chapter “Operating element” on page 14) to the right, the motor will start immediately in the lowest speed (Level 1).
Turn the switch now to the right, as you gradually increase the speed level. Turning the switch to the left to reduce the
speed gradually. In manual mode, this can be done even during operation.
Exit manual mode
Exit manual mode by pressing the On / Off button or by turning the speed control switch back completely
to the left at level 00.
Note
In manual mode, the mixer remains in operation until it is manually stopped.
During operation, the elapsed time is displayed on the display.
Speed Adjustment
The speed can be set from level 01 to level 10 with the speed control switch.
The selected speed setting is displayed as followed:
01, 02, 03, 04, 05, 06, 07, 08, 09, 10
IPMS (integraded Power Management System (in speed levels 1-5)
In mixing of solid foods (e.g. Pastry, nut butters, etc.), the power compensation system will continuously monitor and
adjust the power automatically. This will ensure the mixing content is optimally processed.
With iPMS a dynamic speed may be noticed when mixing softer food in speed level 1-5.
This is not a fault, it is a part of the auto system performance.

19
EN
OPERATING THE TAMPER T42S
Run the tamper only through the lid opening of the measuring cup. (see Fig. 2, page 1). Use only the provided
tamper and no other objects to press the mixing content towards the blades. The less water you use, the more you
have to work with the tamper. If you use other objects, the device can be damaged.
Using of the tamper you can remove any air bubbles, e.g. when preparing dough, in the jar, without touching the blades.
With the integrated temperature display you can make sure your foods are prepared gently.
Always hold the jar with one hand when using the tamper!
To measure the temperature in the jar, please proceed as follows:
1. Switch on the tamper with the On/Off button
2. Take the measuring cup off the lid, leave the lid on the jar.
3. Now hold the tamper into the jar through the opening.
4. The handle of the tamper displays the temperature in °C.
Note
If the display shows the temperature in °F (Fahrenheit), you can change into °C (Celsius) by holding the
On/Off button of the tamper for 3 seconds.
Changing the battery (see also page 1)
1. Unscrew the Cover cup of the handle by turning it anti-clockwise.
2. Now carefully pull out the display from the tamper.
3. Use a coin to remove the old battery and insert a fresh battery.
4. Place the display into the handle and screw the cover cap onto housing slightly tight.
Dispose of the used old battery at the provided collection points. See also page 34.
VORSICHT CAUTION
Benutzen Sie
den Stampfer
nicht ohne
aufgesetzten
Deckel.
Do not use the
tampfer without
the lid.
Benutzen Sie
den Stampfer
nur mit
aufgesetzten
Deckel.
Only use the
tamper when the
lid is attached.
T42S Verwendung nur mit / Use only with
Cube+/ Cube / Square / Canto
Temperature
display
On/O Button
CAUTION

EN
20
SAFETY GUIDELINE FOR CLEANING
This chapter provides important tips for cleaning, maintenance and care of your blender.
Please note the following safety guidelines before and during cleaning of your Volto | N:
Pull the power plug from the power socket before cleaning!
Do not open the housing of the device under any circumstances.
If wet contacts touch the electrical components while charging, this can lead to
an electric shock or even death.
Never place the power plug in water or another liquids for cleaning.
Never clean the power plug with a wet cloth.
Never touch the power plug with wet hands.