Biasi KAPPA 27R Manual

USER MANUAL AND INSTRUCTIONS
KAPPA R
Gas-Fired Natural Draft
Hot Water Boilers
Please Read Instructions Carefully
Save for Future Reference
— Do not store or use gasoline or other ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you can not reach your gas supplier call the re department.
— Installation and service must be performed by a qualied installer, service
agency or the gas supplier.
— These instructions must be afxed on or adjacent to the boiler.
WARNING: If the information in this manual is not followed exactly,
a re or explosion may result causing property damage, personal
injury or loss of life.
KAPPA R
Quincy Hydronic Technology Inc.
3560 Lafayette Rd. Bldg. 2 Unit A
Portsmouth, NH 03801
Phone: [phone]
Fax: [phone]

2 KAPPA R USER MANUAL
Dear Customer:
Thank you for buying a Biasi KAPPA R Boiler System.
The KAPPA R is an efcient oor standing gas red boiler for central heat.
We realize that it is not possible to answer all questions about the KAPPA R boiler system in this manual. Reading
this installation manual does not make the reader an expert in all aspects of installation and operation, and does
not replace the need for a qualied, licensed heating contractor. We urge you to contact your installing contractor
or distributor if you are in question about any aspect of your boiler’s performance. Our main concern is that you
are satised with your boiler and its performance. We require that your contractor complete efciency tests using
instruments.
The external controls and accessories listed in this manual (excluding those supplied inside the boiler) are intended
to serve as guidelines rather than specic recommendations. We realize that other makes and models of such
devices are available and can be used as successfully as those we specify. The installing contractor is the best
judge of a system’s specic requirements, as well as the local availability of certain makes and models of controls
and accessories. The preceding does not apply, however, to the equipment that comes with every boiler, such as the
overheat control and pressure relief valves. The installation of the specic devices supplied with every boiler is
absolutely necessary to the safe operation of the boiler and protection of the heating system.
All BIASI KAPPA R boilers are built in accordance with the ASME boiler and pressure vessel code, and bear the “H”
stamp. The Entire range of applications for the KAPPA R boiler has been tested to standard ANSI Z21.13/CSA4.9
and is CSA compliant.
This KAPPA R boiler has a 1 year warranty on parts and a limited lifetime warranty on the heat exchanger only.
Please be sure to return the warranty registration card as the warranty will be void without your boiler’s serial numbers
(located on label afxed to the boiler), date of installation and the name of your installer being on record in our les.
Thank you for purchasing our KAPPA R boiler. If you have questions or comments, please don’t hesitate to contact
us immediately. Our goal is 100% customer satisfaction.
QHT inc.

KAPPA R USER MANUAL 3
Table of Contents
Section Title Section Number Page Number
Warning - 4-5
Important Information - 6
Product Description 1 7
Specications 2 7-9
Instructions for Use 3 10-12
Warnings 3.1 10
Relling Procedure 3.2 10
Lighting/Operating Instructions 3.3 11
Extinguishing Instructions 3.4 11
Boiler Safety Controls 3.5 11-12
Maintenance 4 13-14
Periodic Maintenance 4.1 13
Daily Maintenance 4.2 13
Monthly Checks 4.3 13
External Cleaning 4.4 14
Warranty - 15

4 KAPPA R USER MANUAL
— Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or
any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you can not reach your gas supplier call the re department.
— Installation and service must be performed by a qualied installer, service agency or the
gas supplier.
— These instructions must be afxed on or adjacent to the boiler.
WARNING: If the information in this manual is not followed exactly, a re or
explosion may result causing property damage, personal injury or loss of
life.
WARNING
Boiler is certied as an indoor appliance. Do not install boiler outdoors or locate where it will be exposed to freezing
temperatures.
DANGER
Caution: Do not store or use ammable materials, chemicals or ammable liquids, especially gasoline, in
the vicinity of this heating appliance.
Caution: Should overheating occur or the gas supply fail to shut off, do not turn off or disconnect the
electrical supply to the pump. Instead, shut off the gas supply at a location external to the appliance.
Caution: Do not use this boiler if any part has been under water. Immediately call a qualied service
technician to inspect the boiler and to replace any part of the control system and any gas control which
has been under water.

KAPPA R USER MANUAL 5
WARNING
Any appliance that burns natural gas, propane gas, fuel oil, wood or coal is capable of producing carbon monoxide
(CO). Carbon Monoxide (CO) is a gas which is odorless, colorless and tasteless but is very toxic. CO is lighter than
air and thus may travel throughout the building.
BRIEF EXPOSURE TO HIGH CONCENTRATIONS OF CO, OR
PROLONGED EXPOSURE TO LESSER AMOUNTS OF CO MAY
RESULT IN CARBON MONOXIDE POISONING. EXPOSURE CAN BE
FATAL AND EXPOSURE TO HIGH CONCENTRATIONS MAY RESULT
IN THE SUDDEN ONSET OF SYMPTOMS INCLUDING
UNCONSCIOUSNESS.
Symptoms of CO poisoning include the following:
dizziness vision problems shortness of breath
headache loss of muscle control unclear thinking
nausea weakness unconsciousness
The symptoms of CO poisoning are often confused with those of inuenza, and the highest incidence of poisoning
occurs at the onset of cold weather or during u season.
A victim may not experience any symptoms, only one symptom, or a few symptoms.
Suspect the presence of carbon monoxide if symptoms tend to disappear when you leave your home.
The following signs may indicate the presence of carbon monoxide:
• Hot gasses from appliance, venting system pipes or chimney, escaping into the living space.
• Flames coming out around the appliance.
• Yellow colored ames in the appliance.
• Stale or smelly air.
• The presence of soot or carbon in or around the appliance.
• Very high unexplained humidity inside the building.
If any of the symptoms of CO occur, or if any of the signs of carbon monoxide are present, VACATE THE PREMISES
IMMEDIATELY AND CONTACT A QUALIFIED HEATING SERVICE COMPANY OR THE GAS COMPANY OR
THE FIRE DEPARTMENT.
ONLY QUALIFIED, LICENSED SERVICE CONTRACTORS SHOULD PERFORM WORK ON YOUR BIASI
KAPPA R BOILER.

6 KAPPA R USER MANUAL
IMPORTANT INFORMATION
Please read this page carefully.
• ALL BOILERS MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL, STATE AND
LOCAL PLUMBING, HEATING AND ELECTRICAL CODES AND ORDINANCES, AS WELL AS
THE REGULATIONS OF THE SERVING ELECTRICAL, WATER AND GAS UTILITIES.
• All systems should be designed by competent contractors, and only persons knowledgeable
in the layout and installation of heating systems should attempt the installation of any
boiler. It is the responsibility of the installing contractor to see that all controls are correctly
installed and operating properly when the installation is completed.
• This boiler is intended for use, only with propane or natural gas. All ammable liquids
(especially gasoline), chemicals, rags, paper, wood scraps, debris, etc., should be kept
away from the boiler at all times. Keep the boiler area clean and free of all re hazards.
• Please read the literature and warranties supplied by the manufacturers of the various
accessory equipment. This equipment is warranted by the respective manufacturers, not
by Quincy Hydronic Technology, Inc. Each piece of equipment must be installed and used
according to the recommendations of the manufacturer.
Codes and Regulations:
Installation of the boiler and related equipment must conform to national, state and local regulating
agencies and codes applicable to the installation of the equipment. In the absence of local
requirements, the following codes apply:
A. ANSI/NFPA - #70 National Electric Code
B. ANSI/NFPA - #211 Chimneys and Vents
C. ANSI/NFPA - #Z223.1 National Fuel Gas Code
C. ANSI/NFPA - Domestic Gas Conversion Burner
D. CAN/CGA - B149 Installation Codes
E. ANSI/ASME - CSD-1
The above codes are available from:
National Fire Protection Association (NFPA)
Battery March Park
Quincy, Massachusetts, 02269
http://www.nfpa.org
Canadian Standards Association Standards Division
5060 Spectrum Way, Suite 100
Mississauga, Ontario, L4W 5N6

KAPPA R USER MANUAL 7
1. Product Description
2. Specications
The KAPPA R series boiler is a cast iron gas red water boiler designed for use in closed forced circulation heating
systems.
This boiler is a Category I draft hood equipped appliance, which must be vented by natural draft using a lined
masonry or listed metal chimney system. An adequate supply of air for combustion, ventilation and dilution of ue
gases must be available in the boiler room.
Figure 2.1
Left side view
1-1/2”
supply
Refil valve
Right side viewFront view
B
C
A
Alternative
circulator
connection
Circulator
Drain valve
1-1/2”
return
1/2” Gas supply
1/2” Gas supply
Vent
damper
(optional)
34-1/2”
(General conguration)
Table 2.1
BASIC
BOILER
MODEL
RATINGS NATURAL GAS PROPANE GAS DIMENSIONS
(inches)
NUMBER OF
SECTIONS
INPUT HEATING
CAPACITY INPUT HEATING CAPACITY AFUE ABC
MBH MBH MBH MBH %
KAPPA 27R 4 106 91 94 80 85.5 19-3/4 25-3/4 5
KAPPA 35R 5 141 121 125 107 85.5 19-3/4 25-3/4 6
KAPPA 44R 6177 151 157 134 85.5 25-3/4 25-3/4 6
KAPPA 53R 7 213 182 188 161 85.5 25-3/4 25-3/4 7
(Specications)
Note: The manufacturer should be consulted before selecting a boiler for installations having unusual piping and
pickup requirements, such as intermittent system operation, extensive piping systems, etc.

8 KAPPA R USER MANUAL
Table 2.2
(*) Values achieved with G20 (natural gas) and with parameters referred to 0% residual O2 in the products of
combustion and with pressure 30 inHg.
DESCRIPTION
KAPPA
27R 35R 44R 53R
Fuel G20
Destination country/countries USA - CANADA
Appliance category I2H
Type of appliance B11BS
Max rated heat input (MBH) 106 141 177 213 MBH
Max heat output (MBH) 90.5 120.5 151 182 MBH
Max rated heat input LP (MBH) 94 125 157 188 MBH
Max heat output LP (MBH) 80 107 134 161 MBH
Useful efciency at Pn Max 85.5 %
Flue gas temperature (∆T) 76 / 168 72 / 161 86 / 186 85 / 185 °C / °F
Required draught 0.02 ÷ 0.05 in W.C.
CO2 (*) 5.4 5.2 6.2 5.6 %
CO (*) < 10 p.p.m.
Maximum admissible temperature 110 / 230 °C / °F
Operating temperature (range) 32÷99 / 92÷210 °C / °F
Minimum return temperature 38 / 100 °C / °F
Maximum operating pressure "PMS" 50 psi
Power supply 120~60 Volt~Hz
Maximum power input (functioning) 125 W
Index of protection X0D IP
Classication Low temperature
Diameter of the stack tting 5 667 inch
Water-side pressure drop (ΔT 18°C) 1.6 3.2 6.7 10.1 ft head
Water content in the boiler 3.25 3.90 4.55 5.20 Gal
Sections 4 5 67n°
(Other specications)

KAPPA R USER MANUAL 9
Figure 2.2
1. Control panel
2. Front panel
3. Flame inspection opening
4. Ignition electrode
5. Burner gas pressure test point
6. Burner
7. Flame detection sensor
8. Boiler drain cock
9. Boiler body
1
9
5
3
10
8
6
7
4
13
12
11
2
17
16
14
15
10. Immersion Well
11. Side panel
12. Gas supply
13. Gas valve
14. Central heating return inlet pipe
15. Central heating flow outlet pipe
16. Flue gas thermostat
17. Flue gas hood
(Primary components)

10 KAPPA R USER MANUAL
3. Instructions for Use
3.1 Warnings:
• In order to guaranty safety and correct operation, it is essential that all the tests are carried out by a competent
and responsible licensed service person before lighting up the boiler.
• The tests are described in the installation, operation and service instructions manual in Section 11 Start Up and
Check Out.
• Ensure that the Central Heating circuit is regularly lled with water checking that the pressure indicated on the
pressure gauge is not lower than 1 bar (14.5 psi) as shown on Figure 3.1.
• If the pressure reading on the pressure gauge is below 1 bar (14.5 psi), then the system will require lling. An
automatic lling valve is normally provided by the installer for this purpose.
• If you are in any doubt regarding this procedure you are advised to contact your Installer or an Approved
Service Person.
• Therefore, when the boiler is not lit or used in cold weather, with consequent risk of freezing do not switch off
the boiler at the circuit breaker or close the gas inlet cock.
• When you expect not to use the boiler for a long period follow the instructions given in section 3.4 on page 11.
3.2 Relling Procedure:
• Isolate the boiler from the electrical supply at the circuit breaker.
• The boiler should have been installed with an automatic ll valve, external to the unit. Open the cold water supply
to the automatic ll valve.
• The pressure should be 1 – 1.5 bar (14.5 – 22 psi).
• The automatic ll valve should maintain this pressure, but not exceed it.
Figure 3.1 (Pressure gauge)
Air introduced into the boiler during this lling process will vent through the automatic air purger tted to the boiler.
You may also nd it necessary to vent air from your heating circuit using the installed vents, however be aware that
excessive venting will cause the pressure in the system to drop. Always ensure that the pressure gauge is set at the
required pressure.

KAPPA R USER MANUAL 11
3. Instructions for Use (Cont.)
3.3 Lighting/Operating Instructions:
Warnings: Do not attempt to start the boiler unless all cleanout doors are secured and sealed. Do not attempt
to light the burner by hand.
1. Check that the cocks connected to the gas inlet pipe and to the supply cold water inlet pipe are open.
2. Power the boiler electrically by setting the power switch shows the sequence (Figure 3.2).
3. If the appliance will not operate, follow the extinguishing instructions on page 12 and call your service technician
or gas supplier.
Figure 3.2
Protection
fuse
Main switch
ON/OFF
Central
heating
circuit
temperature
3.4 Extinguishing Instructions:
When you expect not to use the boiler for a long period:
• Switch off the electricity supply to the boiler, by means of the circuit breaker;
• Shut off the gas supply cock connected to the gas inlet pipe and the cock connected to the supply cold water inlet
pipe (for pipes see Section 8 System Piping in the installation, operation and service instructions manual);
• Empty the water circuit, if there is a risk of freezing.
3.5 Boiler Safety Controls:
1. Every KAPPA R boiler is equipped with a block ue control. The control is designed to prevent the boiler from
running if exhaust products are escaping from the boiler draft control. If the blocked vent control prevents the
boiler from running, do not attempt to place the boiler in operation, shut the power off to the boiler, close the gas
supply and contact your service professional to x the underlying problem.
2. Every KAPPA R boiler is equipped with a ame roll out control. The control is designed to prevent the boiler from
running if ames are pulled out of the burner tray of the boiler. If the ame roll out control prevents the boiler from
running, do not attempt to place the boiler in operation, shut the power off to the boiler, close the gas supply and
contact your service professional to x the underlying problem.

12 KAPPA R USER MANUAL
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a re or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition device which automatically lights the pilot. Do NOT try to
light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the oor
because some gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push
in or turn by hand, don’t try to repair it, call a qualied service technician. Force or attempted repair
may result in a re or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualied service
technician to inspect the appliance and to replace any part of the control system and any gas control
which has been under water.
OPERATING INSTRUCTIONS
3. STOP! Read the safety information above on
this label.
4. Set the thermostat to lowest setting.
5. Turn off all electric power to the appliance.
6. This appliance is equipped with an ignition
device which automatically lights the pilot. Do
NOT try to light the pilot by hand.
7. Remove front access panel.
8. Rotate the gas control knob clockwise to
OFF.
9. Wait ve (5) minutes to clear out any gas. Then
smell for gas, including near the oor. If you
then smell gas, STOP! Follow “B” in the safety
information above on this label. If you don’t
smell gas go to the next step.
10. Rotate the gas control knob counter clockwise
to “ON”.
11. Replace front access panel.
12. Turn on all electric power to the appliance.
13. Set thermostat to desired setting.
14. If the appliance will not operate, follow the
instructions “To Turn Off Gas To Appliance”
and call your service technician or gas supplier.
Gas inlet
Gas control knob
(show in (ON) position)
GAS VALVE - TOP VIEW
Gas outlet
TO TURN OFF GAS TO APPLIANCE
15. Set the thermostat to lowest setting.
16. Turn off all electric power to the appliance if service is to be performed.
17. Push in gas control knob slightly and turn clockwise to “OFF”. Do not Force.
3. Instructions for Use (Cont.)

KAPPA R USER MANUAL 13
4. Maintenance
4.1 Periodic Maintenance:
• For efcient and continuous operation of the boiler, it is required to arrange maintenance and cleaning by an
Authorised Service Person, at least once a year.
• During the service, the most important components of the boiler will be inspected and cleaned. This service can
be part of a maintenance contract.
In particular, you are advised to have the following checks carried out:
• primary heat exchanger;
• burner;
• exhaust fume duct and ue;
• pressurization of the expansion vessel;
• lling up of the central heating circuit;
• bleeding of air from the central heating system;
• general check of the appliance’s operation.
4.2 Daily Maintenance:
Boiler Area:
• Check that the area around the boiler is clear of debris.
• Do not store combustible materials, gasoline or any other ammable vapors or liquids near the boiler. Remove
immediately if found.
• Check for any indication of leakage or corrosion. If anything is found , contact a service technician.
Pressure Gauge:
• Check the pressure on the pressure gauge. Make sure that it does not go below 8 psi or above 24 psi. If the boiler
regularly operates out of this range contact a service professional.
Air Openings:
• Check to make sure that all air openings into the room are free and clear. Also check that the air openings on the
front of the boiler are not obstructed. If there are any blockages clean them away.
4.3 Monthly Checks:
Boiler Piping:
• Visually check all the piping around the boiler to ensure there are no leaks. If any leaks are discovered call a
service professional.
If the pressure on the pressure gauge has gone down:
• It is necessary to ll up the appliance with water again, so as to raise the pressure to an adequate level.
• If lling up with water has to be done very frequent, have a service professional check for leaks.
If noises due to air bubbles are heard during operation:
• You should check that the pressure on the pressure gauge (Figure 3.1 on page 10) is not below the correct setting.
• If required, ll up the system correctly, as described in the Section 3.2 of this manual.
• Bleed any air present in the radiators, if necessary.
Boiler Relief Valve:
• Visually inspect the boiler relief valve for any evidence of leakage. If any problems are found contact your service
professional.
Venting System:
• The venting system of the KAPPA R boiler must be checked on a monthly basis. Failure to do so can cause vent
system failure that could lead to serious injury or property loss.
• Check all components of the vent system for blockage, evidence of leaks, or for corrosion. If anything is found
contact a service professional.

14 KAPPA R USER MANUAL
4. Maintenance (Cont.)
Figure 4.1
Igniction
electrode
Detection
electrode
(Pilot burner ame) Figure 4.2
FLAME RETENTION INNER CONE
(partially lifted from burner)
INNER CONE
(sharply outlined with bright light blue)
OUTER CONE
(darker transparent blue)
INCANDESCENT OUTER MANTLE
(blue with occasional orange flashing)
END VIEW
(Main burner ame)
The pilot ame should have the following proprieties:
• Blue ame.
• Flame sensor glowing red.
Improper Pilot Flame:
• Large ame past ame sensor.
• Small ame not reaching ame sensor.
• Yellow tip ame.
The main burner ame should have the following
proprieties:
• See gure above.
Improper Main Flame:
• Large yellow tip ame.
• Small ame not showing inner or outer cone.
4.4 External Cleaning:
• Before performing any cleaning, disconnect the appliance from the electrical mains, using the dedicated circuit
breaker or serviceman’s switch located adjacent to the appliance.
• To clean the external panels, use a cloth soaked in soapy water. Do not use solvents, abrasive powders or
sponges.
• Do not carry out cleaning of the appliance and/or its parts with readily ammable substances (for example petrol,
alcohols, naphtha, etc.).

KAPPA R USER MANUAL 15
Warranty
For KAPPA R Residential
Floor Standing Gas Boilers
FIRST YEARS-WARRANTY FOR KAPPA R SERIES
RESIDENTIAL HOT WATER BOILERS: QHT warrants
that its boiler and casing are free from defects in material
and workmanship for 1 year from the date of installation.
If any part on the boiler is found to be defective within
this period, QHT will replace the part free of charge.
LIMITED LIFETIME WARRANTY FOR KAPPA R
RESIDENTIAL HOT WATER BOILERS: Biasi warrants
that the heat exchanger of the KAPPA R boilers are free
from defects in material and workmanship for lifetime
from the date of installation to the original purchaser. If
the heat exchanger is found to be defective within the
time frame Biasi will replace the heat exchanger.
These warranties are subject to the condition that a
heating contractor whose principal occupation is the
sale and installation of heating equipment must have
installed the boiler. PARTS, WHICH ARE COVERED,
consists of all materials supplied by Biasi, identied by
QHT’s part numbers in its literature. Other parts supplied
by the installer carry their own warranty and each
manufacturer has responsibility for its own products.
NOTE: ANY PART, WHICH IS REPLACED UNDER
WARRANTY, CARRIES ONLY THE UNEXPIRED
PORTION OF THE ORIGINAL WARRANTY.
OWNER RESPONSIBILITIES:
1. Provide for proper installation, which includes
pressure relief and pressure reducing valves and
high limit safety controls on closed systems.
2. Provide qualied periodic service to prolong proper
operation and service.
3. Insure that boiler is installed in accordance with all
codes and ordinances.
4. This warranty does not apply to boilers, which
are subject to misuse, abuse, neglect, alteration,
accident, excessive temperature, excessive
pressure, or corrosive water or atmosphere.
5. Owner will be responsible for return of faulty
components to Portsmouth, NH, freight pre-paid.
QHT and Biasi will not be responsible for:
1. Components that are part of the heating system, but
were not manufactured by Biasi or QHT as part of
the boiler.
2. The workmanship of the installers of KAPPA R
boilers. Furthermore, this warranty does not assume
any liability for unsatisfactory performance caused
by improper installation.
3. Any costs for labor to remove or replace the faulty
component.
4. Improper boiler application or adjustments, control
settings, care or maintenance.
5. Any damage associated with corrosion or leakage
due to the use of “non-barrier”, plastic pipe in the
heating system.
* IMPLIED WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND MERCHANTABILITY
SHALL BE LIMITED TO THE DURATION OF
THE EXPRESSED WARRANTY. BIASI AND QHT
EXPRESSLY DISCLAIM AND EXCLUDE ANY
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF ANY EXPRESSED OR
IMPLIED WARRANTY.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT
VARY FROM STATE TO STATE.
For prompt warranty service, notify the installer, who, in
turn, will notify the distributor from whom the boiler was
purchased. If this does not result in corrective action,
contact Biasi through Quincy Hydronic Technology
(Address Below) with details in support of the warranty
claim. All claims must be processed through proper
trade channels. Contact with Biasi directly is not
recommended for rapid claim settlement.
Quincy Hydronic Technology Inc.,
3560 Lafayette Road, Bldg. 2, Unit A
Portsmouth, NH, 03801
Tel. [phone]
BIASI BOILER WARRANTY REGISTRATION
IMPORTANT., Registration required. To gain complete warranty
Protection, ll in and mail this card, within 1 year of installation to the address listed below
NAME: ____________________________________________ ADDRESS: ______________________________
CITY: ______________________________ STATE: ________ ZIP: ____________________________________
BOILER SERIAL NO.: ________________________________ DATE OF INSTALL: ________________________
NAME OF INSTALL CO.:______________________________ ADDRESS: ______________________________
CITY: ______________________________ STATE: ________ ZIP: ____________________________________
RETURN TO: QHT, INC., 3560 Lafayette Road, Bldg. 2 Unit A, PORTSMOUTH, NH 03801

*1796230450*
17962.3045.0 2717 16A4 USA
06/07
2017
N