Hearth & Home DVLINEAR36 Series User manual

32-3/8
[822mm]
GAS LINE
ACCESS
6"
[153mm]
2-3/16"
[56mm]
32-1/4"[819mm]
7-3/4"
[197mm]
25-7/8"
[657mm]
43-1/2"[1105mm]
36"[914mm]
41"[1041mm]
LEFT VIEW FRONT VIEW RIGHT VIEW
33-11/16"
[856mm]
15-1/4"
[387mm]
3-1/2"
[89mm]
7"
[178mm]
ELECTRICAL
ACCESS
34-1/2"
[876mm]
16-3/4"
[426mm]
17-1/4"
[438mm]
6-5/8"[168mm]
17-3/4"
[451mm]
1/2"[13mm]
9-13/16"
[249mm]
TOP VIEW
30-3/4"[781mm]
HEAT MANAGEMENT
SYSTEMS ACCESS
10-3/8"
[264mm]
7-1/2"
[191mm]
MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH GLASS SIZE
DVLINEAR36
Actual Framing Actual Framing Actual Framing Actual Framing
32-1/4" x 15-1/4"
(819 x 387)
41"
(1041)
42"
(1067)
30-3/4"
(781)
42"
(1067)
33-11/16"
(856)
32-3/4"
(832)
17-3/4"
(451)
17-3/4"
(451)
DECORATIVE FRONT
32-3/8
[822mm]
GAS LINE
ACCESS
6"
[153mm]
2-3/16"
[56mm]
32-1/4"[819mm]
7-3/4"
[197mm]
25-7/8"
[657mm]
43-1/2"[1105mm]
36"[914mm]
41"[1041mm]
LEFT VIEW FRONT VIEW RIGHT VIEW
33-11/16"
[856mm]
15-1/4"
[387mm]
3-1/2"
[89mm]
7"
[178mm]
ELECTRICAL
ACCESS
34-1/2"
[876mm]
16-3/4"
[426mm]
17-1/4"
[438mm]
6-5/8"[168mm]
17-3/4"
[451mm]
1/2"[13mm]
9-13/16"
[249mm]
TOP VIEW
30-3/4"[781mm]
HEAT MANAGEMENT
SYSTEMS ACCESS
10-3/8"
[264mm]
7-1/2"
[191mm]
Specifications
Additional information can be found in installation and owner’s manuals.
Please consult the manufacturer’s
installation manual for all details and
requirements before making a final
design layout decision.
DVLINEAR36
Direct Vent Gas Fireplace
DVLINEAR36
Barrier Mesh: Integral to
Decorative Barrier Front
25-5/8"
[651mm]
8-7/8"
[225mm]
8-3/16"
[208mm]
25-3/16"
[640mm]
15-5/8"
[397mm]
34-1/4"[870mm]
36"[914mm]
17-1/8"
[435mm]

DV3732SBI
Specifications
DVLINEAR36_0520
Lakeville, MN
Phone: [phone]
DVLINEAR36
Shows center of vent framing hole
for top or rear venting. The center
of the hole is 1" (25mm) above the
center of the horizontal vent pipe.
Product information provided is not
complete and is subject to change
without notice. Product installation
must adhere strictly to instructions
accompanying product to avoid risk of
fire and potential injury.
APPLIANCE LOCATION
WALL PENETRATION
MANTEL LEG/WALL PROJECTIONS
FRAMING DIMENSIONS
47-1/2"
34-1/2"
[1207]
[876]
10"
10"
DO NOT PACK WITH
INSULATION OR
OTHER MATERIAL
6"
MIN.
APPLIANCE OPENING
UNLIMITED
7"
MIN.
WALL MAX.
3'
16" MAX
APPLIANCE OPENING
Combustible/Noncombustible
Without Passive Heat
Combustible/Noncombustible
With Passive Heat
PRODUCT LISTING CODES
US ANSI Z21.88-2017
CAN CSA 2.33-2017
UL307B
47-1/2"
[1207]
TOP VENT
ONE 900ELBOW
SEE INSTALL MANUAL
FOR ALCOVE
INSTALLATION
TOP VENT
ONE 90° ELBOW
18" [457 mm] required
when Passive Heat Side
Discharge Kit is installed.
1/2 IN.
47-1/2"
[1207]
42" [1067]
66"
[1676]
15-3/4"
[400]
17-1/4" [438]
• 8/17 DRAFT COPY
8-5/8"
32-3/4"
17-3/4"
42"
[219]
[832]
[451]
[1067]
NOTE: Header MUST be
installed on end as
shown in the diagram.
HEADER: Two 2 X 4s or Two 2 X 6s
installed on end
AREA TO COMBUSTIBLES
CLEARANCE TO
CEILING 31" [787]
NON-COMBUSTIBLE
FLOOR 0" [0]
COMBUSTIBLE
FLOORING 0" [0]
BEHIND
APPLIANCE 1/2" [13]
SIDES OF
APPLIANCE 1/2" [13]
FRONT OF
APPLIANCE 36" [914]
31"
0"
0" 1/2"
1/2"
36"
[787]
[13]
[13]
[914]
MEASURE FROM TOP
OF APPLIANCE OPENING
TO CEILING
MINIMUM FIREPLACE CLEARANCES /
CLEARANCES TO COMBUSTIBLES
Combustible Mantels
910
11
12
TO CEILING
9
12
16
3
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
TO CEILING
16"
3/8 "NON-COMBUSTIBLE
FINISHING RETURN
DO NOT COVER
NON-COMBUSTIBLE FINISHING RETURN
CEILING
12" MAX.
1/2"
THICK WALL
SHEATHING
14" MIN. BOTTOM
OF MANTEL TO TOP OF
APPLIANCE OPENING
NON-COMBUSTIBLE
MANTEL
6"
MAX.
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
TO CEILING
16"
3/8 "NON-COMBUSTIBLE
FINISHING RETURN
DO NOT COVER
NON-COMBUSTIBLE FINISHING RETURN
CEILING
COMBUSTIBLE MANTEL CLEARANCES
(or other materials above appliance)
NON-COMBUSTIBLE MANTEL CLEARANCES
(or other materials above appliance)
Without Passive Heat With Passive Heat
Without Passive Heat With Passive Heat