Big Mikes Performance Parts STO-N-SHO SNS 62 Reference guide

Installation Procedures
2015 Mustang 2.3, V-6 and 5.0
(Without GT Performance Package)
SNS 62

Warning: Please read directions completely before starting. If you have any
questions please contact BMPP before beginning your installation. Also please
check our website (bigmikesperformanceparts.com) for any updates or changes.
Thank You.
Parts Included: License Plate mounting bracket Assembly. Includes Base Plate and
License Plate Holder.
License Plate mounting Screws: (2) 6mm X 16mm (Phillips head), (2)
6mm nuts with lock washers (10mm wench size)
Base plate mounting screws: (2) 4.2mm X55mm screws (1) 6.3mmX20mm
with washer (2) nylon 1” spacers.
Tools Needed: 7mm & 10mm sockets with ratchet Note: 1/4 inch drive preferred but 3/8
will work (but extra caution will be needed when tightening screws)
Phillips screwdriver & 10mm wrench
1/8 inch drill bit and drill.
Step 1: Insure all parts listed above are accounted for. Note: If at any time during the
installation process you need assistance please call [phone].
Step 2: Separate the license plate holder from the base by simply pulling the pull pin ring
outward and sliding apart.
Step 3: Remove the two center spoiler screws (4.2mm) using a 7mm socket and ratchet. See
figure 1 for location. Then carefully separate the center spot weld that holds the rubber air dam
to the underbody deflector panel as shown in figure 1a.
Step 4: Now position the base mount with the two holes towards the front of the car, centered
over the two holes where the two 4.2mm screws was just removed. Note: The base plate will
slide between the underbody deflector panel and the rubber air dam. Tube will be facing down.
Using the (2) 4.2mm X 55mm screws and the (2) 1” nylon spacers secure the base plate in place.
See figure 2
Step 5: Once base plate is secured using the two front mounting holes, carefully drill one pilot
hole for the rear mounting screw. See figure3.
Step 6: Using the 6.3X20mm screw secure the rear of base plate to the vehicle using the
following method. Caution: When tightening the screw extreme care should be taken not to

over tighten screw or the hole may become stripped and lose its ability to secure the base
plate. Place the screw into the 10mm socket and begin to tighten. Once the screw is flush with
the plate stop. Now Tighten screw one half turn and stop.
Step 7: Secure the license plate and frame (optional) to the license plate bracket using the two
screws and nuts provided. Requires the Phillips screwdriver and 10mm wrench (Not included).
Step 8: Slide the license plate rods into the two tubes located on the base plate. Slide the rods
into the tubes until the rods hit the pull pin. Simply pull the ring on the pull pin and advance the
rods. Release ring and continue to advance rods until the pull pin locks into place. NOTE: If the
rods become difficult to insert into the tubes, spray with WD-40 or any other silicone type
spray lube. See figure 4. In some occasions the license plate may require a little adjustment to
level. Simply pull pin and slide plate out approximately two inches, grab frame at arrows (See
figure 5) and rotate. If plate is high on left or right side, rotate high side down slightly and
release. Verify alignment and repeat as necessary. Once leveled plate will remain level.
Congratulations!! You have just installed the STO N SHOTM front license plate mounting system.
Thank You for your purchase.
Caution: Bracket lowers ground clearance by approx 1/2 inch.
Remove prior to entering automated car wash
Exercise care when entering or exiting steep driveways or damage will occur
Parking Stops or high curbs, stop well before or damage will occur
Remove prior to running on race track
Medium skill level required. If unsure, have bracket installed by your local Dealer or Body shop.
Limited Lifetime Warranty (Transferable)
Big Mike's Performance Parts (BMPP) warrants to the original purchaser only that this
product will be free of manufacturing defects in material and workmanship for the life of the
product to the limitations and exclusions set forth below:
Return product to any authorized dealer. Contact BMPP for the dealer nearest you. Upon
examination, BMPP or its representative will, at its sole option and expense, repair or replace
any product found to be defective. If product to be replaced via mail, BMPP will return the
repaired or replaced unit to you via its usual shipping method from the factory to your address
in the United States of America or Canada only. Any shipping costs for addresses outside of the
United States or Canada shall be the responsibility of the purchaser.

This warranty is transferable when product is attached to a vehicle
REMEDIES FOR BREACH OF WARRANTY.
This Warranty does not include repair for damage caused by improper use or handling,
including but not limited to damage caused by accident, mishandling, improper installation,
abuse, negligence, or any defect caused by repair to the product by anyone other than BMPP.
This warranty does not cover reimbursement for your costs of removing and transporting the
product for warranty service evaluation, or installation of any replacement product provided
under this warranty.
This Warranty will be void if the product was not purchased from an authorized dealer or
reseller.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND
IMPLIED WARRANTIES. ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-
INFRINGEMENT, WITH RESPECT TO THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY
LAW, BMPP SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
EXCEPT TO THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW, EVEN IF BMPP HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Notwithstanding the above, if you qualify as a “consumer” under the Magnuson-Moss
Warranty Act, or applicable state laws, then you may be entitled to any implied warranties
allowed by law for the Warranty Period. Further, some states do not allow limitations on how
long an implied warranty lasts or allow the exclusion or limitation of consequential damages, so
such limitations may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
For the name of your nearest authorized BMPP dealer, contact: Big Mike's Performance Parts at
[phone] or go to bigmikesperformanceparts.com

Fig 1
Fig 1a

Fig 2
Fig3

Fig 4
Fig 5