Bigassfans K3150-A2 User manual

INSTALLATION GUIDE
INSTALLATION GUIDE
GUÍA DE INSTALACIÓN
GUIDE D’INSTALLATION

READ AND SAVE THESE INSTRUCTIONS
Topic Page
Technical Specifications 3
Tools Needed 3
Parts and Hardware
Low Profile Mount 4
Standard Mount 5
Universal Mount 6
Prepare the Fan Site 7
Install Your Fan
Airfoils 8
Lower Cover and Trim 10
Mounting Bracket 12
Mounting: Low Profile 22
Mounting: Standard 30
Mounting: Universal 42
Test Your Fan 54
Models: K3150-A2, K3150-S0, K3150-X2
Installation Guide
For operation, maintenance, and
troubleshooting information, visit
bigassfans.com/support

NOTES

3
HAIKU®BY BIG ASS FANS
Disconnect power to the fan location! Do not use the fan with a dimmer switch!
A licensed electrician must install the fan if required by your local electrical code.
The ground wire must be connected to the supply ground and its length must be longer than the
safety cable!
Technical Specifications
Diameter Weight Operating voltage Operating frequency
132 cm ≤ 6.4 kg 100–240 VAC, 1 Φ 50–60 Hz
152 cm ≤ 7.3 kg 100–240 VAC, 1 Φ 50–60 Hz
213 cm ≤ 11.3 kg 100–240 VAC, 1 Φ 50–60 Hz
Tools Needed
• Ladder
• Wire Strippers
• Phillips Screwdriver
• Wrenches
Box Contents
As you remove the fan from its packaging, make sure you are not missing any components required for
assembly and operation. If you ordered multiple fans, be sure to keep the components of each fan together!
!
!
!

4REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
PARTS & HARDWARE: LOW PROFILE MOUNT
Use the two screw caps that match the color of your fan.
Safety cable not shown.
†
††
Mounting plate
(2) Rubber bumper
(2) Mounting bracket
Lower cover
Lower cover trim
(3) Airfoil
Motor hub
(2) Extension tube screw cap†
Remote control
Mounting hardware
• (4) 6 mm Nylock nut
• Safety cable shackle††
Airfoil hardware
• (6) M5 airfoil screw
• (6) 5 mm lock washer
Wiring hardware
• Wire connectors
• Wire nut
• (2) Wiring cover screw
a
b
g
d
j
e
f
k
c
h
a
b
c
d
e
f
g
h
i
j
k
l
i
l

5
HAIKU®BY BIG ASS FANS
PARTS & HARDWARE: STANDARD MOUNT
Rubber bushing
Mounting bracket†
(2) Mounting brace bracket
Wiring cover
Wiring cover trim
Lower cover
Lower cover trim
(3) Airfoil
Motor hub
Remote control
Mounting hardware
• (2) M6 x 1 x 25 mm socket cap screw††
• (2) M6 x 1 nylock nut††
• M8 Bolt
• 8 mm flat washer
• 8 mm lock washer
• M8 nut
• 2 mm x 2 mm split pin
• Safety cable shackle†††
Airfoil hardware
• (6) M5 airfoil screw
• (6) 5 mm lock washer
Wiring hardware
• Wire connectors
• Wire nut
• (2) Wiring cover screw
a
b
c
d
e
f
g
h
i
j
k
l
m
a
b
g
d
e
f
c
h
l
i
k k
j
m
Do not use the mounting bracket if mounting the fan to a concrete ceiling.
If installing the fan to a junction box, U-shaped ceiling hook, or wood ceiling joist, only
one (1) bolt and one (1) nut are needed. If installing the fan to a J-shaped ceiling hook,
two (2) bolts and two (2) nuts are needed.
Safety cable not shown.
†
††
†††

6REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
PARTS & HARDWARE: UNIVERSAL MOUNT
Mounting bracket
Mounting ball & wedge
Canopy
Extension tube
Wiring cover
(3) Airfoil
Motor hub
Lower cover
Lower cover trim
Remote control
Mounting hardware
• 4 mm self-tapping screw
• 6 mm steel pin
• (6) M4 x 10 mm screw
• (2) M4 lock washer
• Safety cable shackle†
• M6 x 32 mm bolt
• M6 nut
Airfoil hardware
• (6) M5 airfoil screw
• (6) 5 mm lock washer
Wiring hardware
• Wire connectors
• Wire nut
• Cable tie
a
b
c
d
e
f
g
h
i
j
k
l
m
Safety cable not shown.†
a
b
g
d
e
f
k
i
c
h
l
j
m

7
HAIKU®BY BIG ASS FANS
1PREPARE THE FAN SITE
Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable
performing electrical work!
2
1Disconnect Power!
If you are installing the fan directly to the building structure
or to a ceiling-mounted outlet box, the structure or outlet
box must be suitable for fan support.
Disconnect power to the fan location before wiring
the fan!
Mounting Structure
A readily accessible disconnect device shall be
incorporated external to the equipment.

c
b
a
8REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE AIRFOILS
2
Make sure the stickers on the airfoils match the stickers on the fan hub!
1 2
INSTALL AIRFOILS REMOVE PROTECTIVE COVER

9
HAIKU®BY BIG ASS FANS
Moving clockwise around the fan, align each airfoil on the fan hub and secure it with the screws and
washers. Make sure the stickers on the airfoils match the stickers on the fan hub.
Hardware:
a. M5 airfoil screw
b. 5 mm lock washer
Remove and recycle the plastic protective cover (c).
2
1
STEPS COMPLETED

10 REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE LOWER COVER AND TRIM
3
If you purchased the Haiku Light Kit, proceed to the instructions included with the kit. Return to these
instructions once the kit is installed.
1 2
INSTALL LOWER COVER INSTALL LOWER COVER TRIM

11
HAIKU®BY BIG ASS FANS
STEPS COMPLETED
Position the lower cover over the fan motor, and then place both hands flat on the cover and turn it
clockwise to lock it in place.
Align the four slots on the lower cover trim with the four small round tabs on the fan hub. Press and turn
the lower cover trim clockwise to lock it into place.
2
1

12 REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE MOUNTING BRACKET
Outlet Box
If your local electrical code requires the fan to be installed on a ceiling-mounted outlet box, the outlet box must be
suitable for fan support. If there is not an outlet box at the fan location, one should be installed on a ceiling joist or
beam and properly wired.
Concrete Ceiling
If installing your fan on a concrete ceiling, ensure power wiring has been routed to the fan site.
Low Profile Mount. Attach the mounting plate directly to the ceiling using four Ø 8 mm anchor bolts. If required by your
local building and safety code, install a Ø 14 mm anchor hook for the safety cable.
Standard Mount. Install the fan where there is a ceiling hook or other sufficient structural support. If there is not a hook
at the fan site, install a hanger plate using three Ø 12–12.5 mm anchor bolts. Do not use the mounting bracket supplied
with the fan. If required by your local building and safety code, install an Ø 8–8.5 mm anchor hook for the safety cable.
Universal Mount. Attach the mounting bracket directly to the ceiling using three Ø 6 mm anchor bolts. If required by
your local building and safety code, install an Ø 8 mm anchor hook for the safety cable.
Wood Ceiling Joist
If installing your fan on a wood ceiling joist, ensure power wiring has been routed to the fan site. Attach the mounting
plate or mounting bracket directly to the joist using two wood screws (not supplied). Big Ass Fans recommends using
corrosion-resistant 12-11 x 45 mm hex head timber screws with seal.

13
HAIKU®BY BIG ASS FANS
Outlet Box
Page 14
4a Concrete Ceiling
Page 16
4b Wood Ceiling Joist
Page 18
4c

14 REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE MOUNTING BRACKET (OUTLET BOX)
4a
a
b
Low Profile Mount Standard Mount Universal Mount
b
Installation may vary. Refer to the outlet
box instructions.
Installation may vary. Refer to the outlet
box instructions.
Installation may vary. Refer to the outlet
box instructions.
b

15
HAIKU®BY BIG ASS FANS
Make sure power is disconnected from the fan location before installing the mounting plate or
mounting bracket!
If installing a Standard Mount fan, seat the rubber bushing (a) in the eye of the mounting bracket.
Secure the mounting plate or mounting bracket (b) to the outlet box with the hardware supplied with the
outlet box. Refer to the outlet box instructions.
If installing a Universal Mount fan to a sloped ceiling, secure the mounting bracket so that the open side of
the bracket is facing up the slope of the ceiling.
!

50 mm max
40 mm max
ac
40 mm
Ø 8 mm
(anchor bolt)
Ø 14 mm
(anchor hook)
80 mm
100 mm
b
Ø 12–12.5 mm
35 mm 35 mm
45 mm
b
35–40 mm
35–40 mm
ac
50 mm max
40 mm max
ac
Ø 6 mm
112 mm
45 mm 43 mm
b
16 REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE MOUNTING BRACKET (CONCRETE CEILING)
4b
Standard Mount Universal Mount
Install an anchor hook for the safety cable if required by your local building and safety code.
Low Profile Mount

17
HAIKU®BY BIG ASS FANS
!Make sure power is disconnected from the fan location before installing the mounting plate or
mounting bracket!
Low Profile Mount
Drill four Ø 8 mm holes in the pattern shown. The hole depth should not exceed 40 mm.
Remove any dust from the holes. Insert four anchor bolts (a) into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the bolt
sleeves are flush with the ceiling surface.
Position the mounting plate (b) on the anchor bolts. Ensure all four anchor bolts are fully tightened to expand and lock the anchors.
If required by local building and safety codes, install an anchor hook (c) for the safety cable. Drill a Ø 14 mm hole for the anchor hook in the
pattern shown. The hole depth should not exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and fully tighten.
Standard Mount
Drill three Ø 12–12.5 mm holes in the pattern shown. The hole depth should not exceed 35–40 mm.
Remove any dust from the holes. Insert three anchor bolts (a) into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the
bolt sleeves are flush with the ceiling surface.
Position the hanger plate (b) on the anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.
If required by local building and safety codes, install an anchor hook (c) for the safety cable. Drill an Ø 8–8.5 mm hole for the anchor hook
adjacent to the hanger plate. The hole depth should not exceed 35–40 mm. Remove any dust from the hole, and then insert the anchor hook
and fully tighten.
Universal Mount
Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed 40 mm.
Remove any dust from the holes. Insert three anchor bolts (a) into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the
bolt sleeves are flush with the ceiling surface.
Position the mounting bracket (b) on the anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.
If required by local building and safety codes, install an anchor hook (c) for the safety cable. Drill an Ø 8 mm hole for the anchor hook. The hole
depth should not exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and fully tighten.

18 REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE MOUNTING BRACKET (WOOD CEILING JOIST)
4c
Standard Mount Universal MountLow Profile Mount
ba
b
ceiling joist
ceiling joist
ceiling joist
Not Supplied
b
Not Supplied Not Supplied