BigPlanes TOPRC J0005 User manual

第 1 页

第 2 页

第 3 页

Accessory list for the installation of aileron and flap.
3. Apply instand type AB glue to the holes in the aileron
and hinges. Epoxy the aileron to the wing.
1. Apply instand type AB glue to the holes in the flap and
hinges.
4. Apply AB glue to the slots in the ailerons, and
assemble the horns into them.
2. Epoxy the flap to the wing, Keep some space about 1mm
width between the trailing edge and the flap.
5. Apply AB glue to the slots in the flaps and assemble the
horns into them.
第 4 页

6. Assemble the servos to the servo trays.
9. Fix the servo trays with servo assembled to the wings
with screws.
7. Servos assembled ready.
10. Connect the fiber horns to the servo arms with the
linkage and lock each side with screws and nut.
8. Connect the fiber horns to the servo arms with the linkage
and lock each side with screws and nut. 11.Put the plastic screw in the holes of wing, fasten the
bomb socket with bombs to the wing.
第 5 页

12. The picture when the bomb assembled to the wing.
14. Assemble the servos to the stab servo trays and also
rudder servo tray.
Accessory list for the installation of elevator and rudder.
15. Assemble the servos to the stab servo trays.
13. Apply instand type AB glue to the holes in the rudder
and assemble the rudder to the tail fin.
16.Fix the servo trays to the stab with screws, Connect
the fiber horns to the servo arms with the linkage and
lock each side with screws and locknuts.
第 6 页

17.Assemble the servo tray with servo assembled to the tail
fin.
19.Assemble the servo to appropriate position in the
fuselage of the belly brake section.
18.Connect the fiber horns to the servo arms with the
linkage and lock each side with screws and locknuts.
20.Connect the plastic horn in the belly brake to the
servo arm with the linkage and lock each side with
screws and locknuts.
Accessory list for the installation of belly brake.
Accessory list for the installation of main gear door.
第 7 页

21.Trim slots in the gear door,glue the pin hinges into the
gear door and fuselage, assemble the gear door to the
fuselage with screws.
24.Assemble the servos of gear doors to the fuselage, trim
a lot to appropriate position on the gear house of the
fuselage.
22.Assemble the inner gear door to the fuselage with
screws
and epoxy.
25.Connect the innner gear doors and the servos througn
the slot in the fuselage
23.The picture when the inner gear door assembled
ready.
Accessory list for the installation of Nose gear.
第 8 页

26.Fix the the plastic horn base to propriate position on
the fuselage with glue and screw, assemble the plastic
horn to the nose half gear door with glue and screws.
29.Assemble the nose retract to the fuselage with screws
and assemble the back half nose gear door.
27. Connect plastic horn to the servo via push rod and
screws.
30.Connect the back half nose gear door to the landing
gear with push rood and screws.
28. Assemble the nose landing gear and the servo to the
nose retract.
31.The picture when the nose gear up.
第 9 页

Accessory list for the installation of main gear.
34.Assemble the main gear door to the landing gear
with screws.
32.Assemble the main retracts to the wings.
35.The picture when the main gear up.
33.Glue the plies to the socket rings on the landing gear.
Accessory list for the installation of tail pipe.
第 10 页

36.Put the fuselage plugs to one fuselage, assemble the two
fuselage together through the fuselage plugs.
39.Assemble the engine and tail pipe to the fuselage
with screws.
37.When the fuselages be assembled together, fasten them
with screws from the fuselage.
The accessory list for fix the wing
38.Assemble the fuel tank to the fuselage.
40.Fix the wing to the fuselage through the wing tubes.
第 11 页

41.Lock the wings from the holes on the bottom fuselage with
screws.
43. Assemble the nose cover to the fuselage with
rubber band.
42.Assemble the stab to the fuselage through the stab tubes
and lock them with screws.
44.The picture when the hunter assemble ready.
第 12 页

45. Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
46. Adjust the travel of each control surface to the values
in the diagrams. These values fit general flight
capabilities.Readjust according to your needs and flight
level.
47. Check all the datas well. make sure all sections glue
tightly. Otherwise if coming off during flights, you'll lose
control of your airplane which leads to accidents!
48.C.G: Never fly before checking the CG's required
position. Never fly the model without well balancing.
第 13 页

第 14 页