BigPlanes Zero Fighter User manual

Before commencing assembly,please read these instructions thoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
Assemble this kit only in places out of children s reach!
Take enough safety precautions prior to operating this model.
,
You are responsible for this model s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
Could cause serious injury or even death
SPECIFICATION
Warning!
！
Wing Span: 2320 mm (91.3in)
2
Wing Area: 93.4 dm (1448 sq.in)
Total Length: 2100 mm (82.7 in)
Engine :60-100cc gas engine
Radio : 8 channels ,9 servos
Zero Fighter

2
REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Needle Nose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
1
2
3
.
.
.
Warning!
！
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
2mm
Assemble left and right
Sides the same way.
R
L
Apply instant glue
(CA glue,super glue).
C.A
Apply epoxy glue.
BA
Cut off excess.
Do not overlook this symbol.
1
A minimum 6channel radio for airplanes (with 8servos).
And dry batteries.
CAUTION:Onlyuseaminimum6channelradiofor
airplanes!(Nootherradiomaybeused!)

!
12 AA-size Batteries
A minimum 8 channel
transmitter for airplanes.
2
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Muffler
Glow plug
3
Purchase a propeller that
will match your engine
4
Silicone Tube Fuel Filter
5
Required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
3
Glue
6
Instant glue Epoxy Glue
3
Other equipment for enhancing
airplane operation & perormance
7
12V Battery (for starter)
Engine Starter
Propeller splinner
M Aodel irplane ena
gine
60-100cc gas engine

Accessoriespackinglist
-------2.6x12Tpscrew----------------34
-------2.5x8mmTpscrew-------------10
----pivot&roundhinges---17
-----------pinhinges-----------------8
--------------horn--------------12
--------------horntray--------6
---------Mainwingtube(32x1110mm)--------1
-------------stabilizertube(12x485mm)---------1
--------------Plyplate(3mm)-------------1
--------------Plyplate(6mm)------------1
--------------enginesupport-------------1
--------------geardoorA-------------2
--------------geardoorB-------------2
--------------Autenna-----------------1
--------------Droptankrack---------1
-----------Droptank---------1
-------Canopy----------1
----Fueltank(1000cc)-----1
--------------M3x16mmscrew--------6
---------------------Clevis(A)------------6
-------------------Clevis(B)--------------6
--------------Copperball(A）-------6
---------------Copperball(B)---------6
----------------Locknut-----------------12
----------------Locknut------------------6
---------butterflynut(M8)------------4
---------butterflynut(M6)------------2
-----------------horn---------------------2
--------------horntray-------------------2
--------------Retainer(M2)----------2
-----------3mmPlyplate---------------6
-------3x20mmTpscrew---------------2
------M3x12mmscrew------------2
------M3x12mmscrew------------2
------3x20mmscrew---------------6
------M2x10mmscrew-----------14
------M3x3mmscrew--------------1
------------M2Nut-------------------8
---------LinkageStopper-----------1
---------Angleironframe----------4
---------Angleironframe----------8
------M4x20mmscrew------------8
------Scaleexhausttubes---------7
----pushrod2x50mm---2
--pushrod2x100mm---1
----pushrod3x80mm---6
----steelwire1800mm--2
---------Aluminiumtubes-----2
---------Copperjoiner----------4
------Ruddersteeringarm----1
----------Doublerocker------------1
--------------Retainer(M3)------------4
------M4x10mmscrew------------2
------------Washer------------------10
---------Landinggearstruts----------2
--------------Retractsstrut-------------2
--------------circuitboard--------------1
----Mainwheels（4.5inch)-------2
---------wrench--------------1
---------extensioncords----3
--------AluBlock(A)----2
--------AluBlock(B)----2
-----4x20Tpscrew----2
-----M3x20screw-----4
-----------M3x8screw-------8
-----Taillandinggear-----1
---------5mmAxle----------2
-----------------------Metalring----------2
----------------M4x4mmscrew----------4
----------------M3x3mmscrew----------2
Optionalparts(Electriclandinggear)
3

!
3
2
1
5
4
4
Install the aileron and flap
Install the servo of aileron
Install the servo
Aileron
Flap
Install the aileron and flap
Bottom view
Install the servo of flap
Accessory list for this page.
L
R
L
R
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
Ј
Warning!
L
R
FlapAileron
A B
A B
A B
Make sure hinges are
mounted in the same line
L
R
Flap Aileron
Tailing edge
Aileron
4mm
L
R
L
R
Servo line
A B
Rod adjuster
M3*80mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
4
3mm Lock nut
2.6X12mm Tp Screw
8
L
R
Servo line
A B
Rod adjuster
2.5X80mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
4
3mm Lock nut
2.6X12mm Tp Screw
8
Hinge
Hinge
- - - - - - - - 6
- - - - - - - - 8
Hinge
Hinge
Rod adjuster
M3X80mm rod
HORN
3X16 Screw
Rod adjuster
4
8
4
8
4
8
3mm Lock nut
8
6
2.6X12mm Tp Screw
16

L
R
HORN--4
3X16 Screw --2
3mm Lock nut--2
A B
2.3x10mm Tp Screw
- - - - 8
HORN--4
2.3x10mm Tp Screw
- - - - 8
!
8
7
6
10
9
5
Accessory list for this page.
Install the elevator
L
R
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
Warning!
L
R
Bottom view
Install the elevator
make sure hinges are
mounted in the same line
A B
Hinge
- - - - - - - - 6
Install the elevator servos
Tailing edge
Elevator
4mm
Install the elevator servos
L
R
L
R
L
R
Install the rudder
make sure hinges are
mounted in the same line
Hinge
- - - - - - - 3
A B
A B
Hinge
- - - - - - - - 6
Rod adjuster M3X80mm rod
3X16 Screw Rod adjuster
2
2
2
2
2
3mm Lock nut
- - - - - - 2
- - - - - - 2
Ball bearing
Ball bearing
Rod adjuster
M3X80mm rod
3X16 Screw
Rod adjuster
2
2
4
2
4
3mm Lock nut
- - - - - - 2
- - - - - - 2
Ball bearing
Ball bearing

Drill holes with
the specified
Diameter(here:3mm)
3mm
3mm
A B
----------------1
Doublerocker
----------------1
m3x3screw
----------------1
steelwire900mm
----------------2
Aluminiumtubes
----------------1
steelwire900mm
----------------2
Aluminiumtubes
butterflynut(M6)
---------2
----------------1
Doublerocker
----------------1
m3x3screw
----------------2
steelwire900mm
----------------4
Aluminiumtubes
butterflynut(M6)
---------2
!
13
12 15
14
6
11
Accessory list for this page.
Install the rudder
Install the rudder
Install the rudder
Install the stabilizer to the fuselage
Install the tail wheel
M4X10 Screw
2
M4X10 Screw
2
------Ruddersteeringarm----1
------Ruddersteeringarm----1

!
18
17 20
19
16
7
Accessory list for this page.
Install the main landing gear
Install the main landing gear
L
R
Install the main landing gear
Install the main landing gear
L
R
4x20Tpscrew----8
BA
3mm
8mm
----------------2
pinhinges
---------------------4
M2x10mmscrew
------------------------4
M2 nut
----------------2
horn
----------------2
horntray
Install the main landing gear door
3mmPlyplate---6
3X10mm screw
- - - - - 8
4x20Tpscrew----8
----------------2
pinhinges
---------------------4
M2x10mmscrew
------------------------4
M2 nut
----------------2
horn
----------------2
horntray
3X10mm screw
- - - - - 8
C.A
3mmPlyplate---6
----pushrod2x50mm---2
--Retainer(M2)----2
---M2x10mmscrew---14
----pushrod2x50mm---2 --Retainer(M2)----2
---M2x10mmscrew---14

!
23
25
8
21 24
22
Accessory list for this page.
Main wing&Horizontal/Vertical tail
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
Warning!
！
A A
B B
C C
Installing the drop tank
Main wing
(Put the servo line into the fuselage)
Installing the drop tank to the fuselage
A
A
B
B
C
C
butterflynut(M8)
---------4
3x20mmTpscrew
------------2
3mm
M3x12mmscrew
------------1 ------------1
Droptankrack Droptank
------------2
Installing the engine
butterflynut(M8)
---------4
3x20mmTpscrew
------------1
------------1
Droptankrack
Droptank
------------2
------------2
M3x12mmscrew

!
28
30
9
26 29
27
Accessory list for this page.
Installing the ply plate
Install the scale exhaust tubes
Installing the ply plate
Assembly of the rudder servo
4mm
4mm
---Scaleexhausttubes---7
----2.6x12Tpscrew------7
---------Angleironframe----------8
------M4x20mmscrew------------8
Angleironframe----------4
----3x20mmscrew--4 ----Plyplate(3mm)---1
---Plyplate(6mm)----1
----2.6x12Tpscrew-----3
Copperjoiner---2
Retainer(M3)--------2
Aluminiumtubes---2
M2x10mmscrew-----2
Fuel tank
Throttle servo
--pushrod2x100mm---1
LinkageStopper---1
Install the scale exhaust tubes
---Scaleexhausttubes---7
----2.6x12Tpscrew------7
Angleironframe----------4
---------Angleironframe----------8
------M4x20mmscrew------------8
----Plyplate(3mm)---1
----2.6x12Tpscrew-----3
Copperjoiner---2
Retainer(M3)--------2
Aluminiumtubes---2
M2x10mmscrew-----2
--pushrod2x100mm---1
LinkageStopper---1
----3x20mmscrew--4
---Plyplate(6mm)----1

!
33
32 35
10
31 34
Accessory list for this page.
Install the cowling
Install the canopy
Install the canopy
Install the canopy
Install the canopy
------3x20mmscrew----6
------------Washer----------6
--------------Autenna-----------------1
Autenna-----------1
3x20mmscrew----6
Washer----------6

38
37 39
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
36
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
11
Adjustment.
Never fly before checking the Cg’s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
警告
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
140-150mm
Adjustment
Side view
Adjustment.
Aileron
Flap
CG
45
45
90
45
45
45
45