Billion BiPAC 2060G User manual

BiPAC 2060G
Wireless-G Powerline Adapter
Quick Start Guide

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 2 -

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 3 -
Package Contents
BiPAC 2060G Powerline Adapter (Switching)
Important Safety Instructions
Place the BiPAC 2060G on a stable surface.
Unplug the coupler from the wall outlet before cleaning. Use a damp cloth for
cleanin
Do NOT use the BiPAC 2060G in high humidity or high temperatures
Do NOT open or repair the case yourself. If the BiPAC 2060G is too hot,
unplug the power immediately and have it repaired at a qualified service
center.
Do NOT use liquid cleaner or aerosol cleaners.
Do NOT operate the device near water.
Avoid using this product and all accessories outdoors.
Because the product sends data over the powerline, it is recommended that
you plug directly into a power outlet.
Only a qualified technician should service this products. Opening or removing
covers may result in exposure to dangerous voltage points or other risk.

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 4 -
The Front LEDs
LED Meaning
1 ACT:
(Activity)
Blinking : Looking for Powerline Devices
Fast Blinking : Transmit/receive data
OFF: No Network Traffic
2 COL:
(Collisions) Blinking : Collisions Detected
OFF: No Collisions Detected
3 Power : Lit when power is on.
4 WLAN :
Lit when Wireless connection.
Blinking when transmitting / receiving wireless data traffic.
4
1
3
2

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 5 -
Installation
Hardware Installation：
Plug the BiPAC 2060G Powerline Access Point into an outlet
Connecting a Wireless Device to the Access Point：
If you are connecting to the BiPAC 2060G Access Point with a
wireless/Homeplug device, all wireless configuration parameters must be
configured to match.
The default setting for Homeplug Access Point
Wireless-G Powerline Adapter default setting
1 Default IP 192.168.1.253
2 User name admin
3 Password admin
4 SSID default
5 Channel 11
6 WEP off
7 Network Password HomePlug
To connect to your BiPAC 2060G Access Point you must have
an IP address .There are two ways for your wireless network
adapter to obtain an IP address:
; Typical Setup
ÆObtain an IP address automatically from a router on your
Powerline network.
; Advanced
ÆIf your router does not have a DHCP server, you will need to
manually configure a static IP address for your wireless
adapter that is on the same subnet as your other network
Attention

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 6 -
Plan the installation of your Powerline network
1. Create a Powerline network using an Ethernet DSL/cable router.
NOTE:
You will need at least two powerline adapters to create a Powerline network..
BiPAC 2060G plugged into
power outlet

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 7 -
2. Create or extend a wireless network using a Powerline router (Ethernet or
wireless).
Troubleshooting
(Wireless):
‧ Verify that your network adapter is configured to connect to the same SSID.
For optimal wireless performance, be sure to keep the antenna free from
obstructions.
(PowerLine):
‧Verify that your Powerline network passwords are identical for all of your
PowerLine adapters.(Passwords are case sensitive)
‧All PowerLine adapters need to have the same network password to
communicate.
‧The default network password for the BiIPAC-2060G is “HomePlug”
ÆHow to reset your device to factory defaults.
‧There is a small hole on the right side of the device labeled RESET.
‧With the end of a paper clip press the button inside the unit. The LEDs on the
BiPAC 2060G will flash. Your device is now reset to factory default settings.

Billion BiPAC 2060G Wireless-G Powerline Adapter
- 8 -
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the
User’s Manual.If you cannot resolve the problem with the Troubleshooting
chapter, please contact the dealer where you purchased this product.
WORLDWIDE
http://www.billion.com
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.