Billion BiPAC 3011G User manual

BiPAC 3011G WLAN 11g USB Adapter
Quick Start Guide

This product is in compliance with the essential requirements and other
relevant provisions of the R&TTE directive 1999/5/EC.
Product Name: BiPAC 3011G WLAN 11g USB Adapter
Model Name : BiPAC 3011G MAX. OUT POWER
COUNTRY CHANNELS INDOOR OUTDOOR
Spain 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
France 2400-2454 MHz 1-8 < 100 mW EIRP < 100 mW EIRP
France 2454-2483.5 MHz 9-13 < 100 mW EIRP < 10 mW EIRP
Italy 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
UK 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Netherlands 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Germany 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Austria 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Belgium 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Switzerland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Luxemburg 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Ireland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Portugal 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Norway 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Denmark 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Finland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Iceland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Greece 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Lichtenstein 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Sweden 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
1

FCC INFORMATION
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter. The
equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio
communication. However, there is no grantee that interference will not occur in a
particular installation. If this equipment dose cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Notice: The Part 15 radio device operates on a non-interference basis with other
devices operating at this frequency. Any changes or modification not expressly approved
by the party responsible could void the user’s authority to operate the device.
REGULATORY INFORMATION
BiPAC 3011G WLAN 11g USB Adapter must be installed and used in strict accordance
with the instructions. This device complies with the following radio frequency and safety
standards.
USA - Federal Communications Commission (FCC)
This device complies with Part 15 of FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
2

1. Overview
1.1 Product Feature
Complies with the IEEE802.11b/g 2.4GHz (DSSS) standard
High-speed data transfer rate – up to 54Mbps
Support 64/128-bit WEP Data Encryption function for high level of security
Supports peer-to-peer communication among any wireless users, no
Access Point required
Automatic fallback increases data security and reliability
Supports the most popular operating system: Windows 98SE/ME/2000/XP
Portable and mini-size design
Suitable for Any Notebook or Desktop PC
1.2 Application
Wireless LAN network defined by IEEE 802.11b standard committee could be
Configure as: Ad Hoc wireless LAN or Infrastructure wireless LAN. Ad Hoc
network is a group of notebooks with wireless LAN adapter, called a BSS (Basic
Service Set). These notebooks use their wireless LAN adapter to communicate
with each other directly.
Figure 1.2.1 Ad Hoc wireless network
3

The most obvious differentiation between Infrastructure wireless network and
Ad Hoc wireless network is that the notebooks in Infrastructure wireless
network can make use of the resource in the Internet through Access Point.
Figure 1.2.2 Infrastructure wireless network
To set up your notebook’s network as the type of “Ad Hoc” or “Infrastructure”
wireless network depends completely on your requirement. Generally, if your
network environment has an Access Point, it’s recommend that you set it as
“Infrastructure” mode to connect to the Internet.
1.3 Package Contents
Item: Location:
BiPAC 3011G WLAN 11g USB Adapter BOX
BiPAC 3011G WLAN 11g USB Adapter drivers/utility CD-ROM
BiPAC 3011G WLAN 11g USB Adapter User Manual CD-ROM
BiPAC 3011G WLAN 11g USB Adapter Quick Start Guide CD-ROM
1.4 System Requirements
Notebook PC or desktop PC with one free USB 2.0 port
32MB memory or greater
300MHz processor or higher
Microsoft Windows XP / 2000 / Me / 98SE
4

2 Driver installation
1. Insert the BiPAC 3011G WLAN 802.11g USB Adapter CD in the CD-ROM drive
and wait until first page appears.
Note: In case this screen does not appear, in Windows Explorer browse to your
CD-ROM and double-click the Setup.exe file.
2. Click Install Driver and click next in the next page.
5

3. Click [Next] to accept, or [Browse] to change the default destination folder.
4. Click [Next] to accept, or change the default Program Folder name.
6

5. Click [Yes] to accept add shortcut to Desktop, or [No] to next setp.
6. Click [Yes] to accept the driver install.
7. Click [Yes] to accept the driver install
7

8. Now connect your BiPAC 3011G WLAN 11g USB Adapter to the USB port of your computer. In the
Find New Hardware Wizard that appears on your screen select [No, not this time], and click [Next].
9. Select [Install the software automatically (Recommended)], and click [Next]
10. Click [Finish] to finalize the installation. Your BiPAC 3011G WLAN 11g USB Adapter is now
ready for use.
8