Billion SG3010 Series User manual

Last revised on Apr. 2013
User Manual
SG3010/SG3015 Series
Compact ZigBee Power Meter

Table of Contents
Chapter 1: Product Introduction...........................................1
Chapter 2: Installing the Adapter .......................................... 2
Package Content............................................................2
Important note for using this device ............................2
Device Overview ............................................................3
SG3010/SG3015-T1 ...................................................3
SG3010/SG3015-T2 ...................................................4
SG3010/SG3015-T3 ...................................................5
SG3010/SG3015-T4 ...................................................6
Connecting the Power Meter.........................................7
SG3010/SG3015-T1 ...................................................7
SG3010/SG3015-T2 ...................................................8
SG3010/SG3015-T3 ...................................................9
SG3010/SG3015-T4 .................................................10
Networking Setup ...................................................11
Appendix: Product Support & Contact................................13

1
Chapter 1: Product
Introduction
Thank you for purchasing Billion SG3010/SG3015 T1/ T2/ T3/ T4 Compact Smart Power Meter.
This compact smart power meter has a number of functions for electricity estimation and wireless
transmission. The meter is able to indicate various information for electrical appliance in use
including Total Cumulative Kilowatt Hours, Interval Cumulative Kilowatt Hours, Electricity cost,
Elapsed Time and others. It is suitable for electricity data collection or use as a standalone power
meter.
• Measurement function
The measurement functions for this power meter are including Active Power (W), Total
Accumulated Electricity Consumption (kWh), Interval Electricity Consumption (kWh), Voltage (V),
Current (A), Apparent Power (VA), Power Factor (PF) and others, which provides to people that
require more electricity data.
• High Resolution
Capable of measuring very small electricity power to 0.01W as well as very small electricity energy
to 0.001kWh.
• Great Accuracy
Electricity Energy (kWh) measure accuracy ± 0.5% (At PF=1.0, at Rated Current). Electricity
Power (W) measure accuracy ± 1% (At PF=1.0, at Rated Current).
• Power Surge Protection (For SG3010/SG3015-T1 and SG3010/SG3015-T2 Only)
Built in real zero-crossing switch and soft start power surge protection device.
• Small in Size
Includes electricity measure and wireless transmission module, the dimension is
10.06cm(W)×3.8cm(H)×3.4cm(D).
• Electricity Cost Calculation
Input the electricity rate into the Power Managemant System will automatically calculate Total
Cumulative Electricity Cost or Interval Electricity Cost, as well as estimating 24hr electricity cost
assuming current electricity usage and other information.

Chapter 2: Installing the Adapter
Package Content
Power measurement pack:
• Billion SG3010/SG3015 Compact Smart Power Meter
• CD (containing User Manual)
Important note for using this device
2
●The maximun current of the device is 10A for SG3010-T1/T2 and 15A for SG3015-T1/T2
●Do not use the device in high humidity or high temperatures
● Do not open the case yourself. If the device requires repair or maintenance, please turn
off the power and have it repaired at a qualied service center
The communication distance will be shortened if there is a wall or shelter between the
power meter and ZigBee coordinator.

3
Device Overview
SG3010/SG3015-T1
1Power Plug
(100-240V) Put the plug in the socket.
2Meter Status
Indicator
Lit green when the device is not connected.
Blinking when the device is connected.
3
Power Meter
Setting Hidden
Button
Press this button to detect signal strength.
Blinking green 5 times when the signal achieves the highest level;
Blinking orange once when the signal is in the lowest level.
4 Energy Indicator Note: It will ash once when electricity consumption has
accumulated to 1wh (0.001kWh).
5 Power Outlet Insert the plug of an electrical appliance that you intended to
monitor into the product’s outlet.

4
SG3010/SG3015-T2
1Input Power
(100-240V) Connect to the power supply terminal.
2Meter Status
Indicator
Lit green when the device is not connected.
Blinking when the device is connected.
3
Power Meter
Setting Hidden
Button
Press this button to detect signal strength.
Blinking green 5 times when the signal achieves the highest level;
Blinking orange once when the signal is in the lowest level.
4 Energy Indicator Note: It will ash once when electricity consumption has
accumulated to 1wh (0.001kWh).
5Output Power
(100-240V)
Connect to the electrical appliance at the load output terminal that
you intended to monitor.

5
SG3010/SG3015-T3
1Input Power
(100-240V) Connect to the power supply terminal.
2Meter Status
Indicator
Lit green when the device is not connected.
Blinking when the device is connected.
3
Power Meter
Setting Hidden
Button
Press this button to detect signal strength.
Blinking green 5 times when the signal achieves the highest level;
Blinking orange once when the signal is in the lowest level.
4 Energy Indicator Note: It will ash once when electricity consumption has
accumulated to 1wh (0.001kWh).
5Split-core Current
Transformer Install to the electrical appliance that you intended to monitor.

6
SG3010/SG3015-T4
1Input Power
(100-240V) Connect to the power supply terminal.
2Meter Status
Indicator
Lit green when the device is not connected.
Blinking when the device is connected.
3
Power Meter
Setting Hidden
Button
Press this button to detect signal strength.
Blinking green 5 times when the signal achieves the highest level;
Blinking orange once when the signal is in the lowest level.
4 Energy Indicator Note: It will ash once when electricity consumption has
accumulated to 1wh (0.001kWh).
5Split-core Current
Transformer Install to the electrical appliance that you intended to monitor.

7
Connecting the Power Meter
It is easy to connect SG3010/SG3015-T1/T2/T3/T4 simply by performing the following instructions.
Note: Ensure that the Power Meter is turned off or the power supply is cut off before
beginning setup.
SG3010/SG3015-T1
1. Plug in the electrical appliance that you intended to monitor to the Power Meter’s
outlet.
2. Plug the Power Meter directly into the wall outlet/socket.
3. Set up the connection between SG3010/SG3015 - T1 and ZigBee Coordinator (Please refer
to Networking Setup section).
4. After use, extract the appliance’s plug and then pull out the plug from the wall to complete
the power-off procedure.

8
SG3010/SG3015-T2
1. Connect the Power Meter’s output power end to the electrical appliance at the load output
terminal that you intended to monitor.
2. Connect the input power end to the power supply terminal.
3. Set up the connection between SG3010/SG3015 – T2 and ZigBee Coordinator
(Please refer to Networking Setup section).

9
SG3010/SG3015-T3
Following the instructed electricity current direction at the bottom of the split-core CT to install the
CT to L1.
1. Following the instructed electricity current direction at the bottom of the split-core CT toin-
stall the CT to L1.
2. Connect the 2 input power ends to the load output terminals of the main switch, the Black
wire to “L1”, and the White wire to ”N”.Please refer to Installation section for detail instruc-
tion information.
3. Set up the connection between SG3015 – T3 and ZigBee Coordinator (Please refer to Net-
working Setup section).

10
SG3010/SG3015-T4
Note: Ensure the power in the main switch box has been turned OFF while installing the
product.
1. Following the instructed electricity current direction at the bottom of the split-core CT to
install the 2 CTs to L1 and L2 respectively.
2. Connect the 2 input power ends to the load output terminals of the main switch, the Black
wire to “L1”, and the White wire to ”L2”.
3. Set up the connection between SG3015 – T4 and ZigBee Coordinator (Please refer to
Networking Setup section).

Networking Setup
Pairing the smart meter
Step1: After setting up the power connections, you can start to pair the meter. First, please check
if the status LED lights green, which means that the smart meter has not been paired with other
meters.Ifyoursmartmeterisusedforthersttime,thencontinuethesetup.IfLEDblinks,please
refer to “un-pairing the smart meter” section to unpair your smart meter.
Step 2: Push ZigBee button on the rear panel of ZigBee Coordinator to make a connection.
Step 3: Then, ZigBee/WPS LED in the front panel will blink quickly around 60 seconds.
Step 4: The smart meter will be automatically paired and join to the network. The LED light would
blink slowly and steadily, indicating that the power meter is successfully connected.
11

12
Un-pairing the smart meter
If you attemp to disconnect the the smart meter and leave the current network group, do the
following un-pair setup steps. Please note that before pairing the ZigBee coordinator with smart
power meters, check if the status LED of the smart meter lights green. If the status LED blinks
green,itmeansthatthemeterhasbeenpaired.Pleaseun-pairthesmartmeterrst.
Step 1: Cut off the power source of your smart meter and then turn on the power meter again.
Step 2: Press and hold the hidden button within 5~35 seconds after power on and then the LED
will blink around 6 seconds.
Step 3: Cut off the power source during the blinking and then turn on the smart meter again. Then
you can see the LED lights green steady. You have successfully un-paired the smart meter.
Please note that before the smart meter is power on, remember to shut down the
ZigBee coordinator in case the meter is paired to the device again.

13
Appendix: Product Support & Contact
If you come across any problems please contact the dealer from where you purchased your prod-
uct.
Contact Billion
Worldwide:
http://www.billion.com