Billion BiPAC 7800(N) User manual

BiPAC 7800(N)
(802.11n) Dual WAN
ADSL2+ Firewall Router
Quick Start Guide

Billion BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
- 1-
Package Contents
BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
CD containing the on-line manual
RJ-11 ADSL/telephone cable
Ethernet (RJ-45) cable
Three 2dBi detachable antennas (Wireless model only)
Power adapter
Quick Start Guide
Splitter/ Micro-filter (Optional)
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.

Do not use the
router
in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.

Avoid using this
product
and all
accessories
outdoors.

Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention

Billion BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
- 2-
H
Ha ar rd dw wa ar re e O Ov ve er rv vi ie ew w
The Front LEDs
The Rear Ports
*Note: For WPS configuration, please refer to the WPS section of User Manual.
Connect the
supplied power
adapter to this jack
Connect the supplied
RJ-11 cable to this port
when connecting to the
ADSL/telephone
network
Press more
than 5 seconds
to restore the
device to its
default mode.
Connect your computer
to a LAN port using the
included Ethernet cable
(with RJ-45 cable)
When power on
LED
will
be
lit
green. When the system is
booting it will blink orange at the
same time. While the system is
ready it will only be lit green.
When system boot fails or in
emergency mode it will only be
lit orange.
WAN 10/100M Ethernet port
(with auto crossover
support); connect Cable
Modem, VDSL, and Fiber
Modem or PON optic lines
with your RJ-45 cable
Lit when connected to an
Ethernet device.
Lit green for 1000Mbps;
Lit orange for 10/100Mbps.
Blinking when data is being
Transmitted / Received.
Lit Green when
successfully connected
to an ADSL DSLAM,
(“line sync”).
L
it when connected to
a
broadband connection device.
Lit orange for 10/100Mbps.
Blinking when data is
transmitted
/
received
.
Power
ON/OFF
switch
Lit green when
a
wireless
connection is established. Flash
orange when WPS configuration
is in progress. Flashing green
when data is sent / received.
Connect the
detachable antennas
Push WPS button to
trigger Wi-Fi Protected
Setup *
Lit orange when WAN port
fails to get IP address.
Flashes green when WAN port
gets IP ad dress successfully
and when data is transmitted.

Billion BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
- 3-
H
Ha ar rd dw wa ar re e C Co on nn ne ec ct ti io on n
Users will not be able to connect to the internet through EWAN if DSL is already connected to
the internet. Only one connection type (EWAN or DSL) is allowed to connect to the internet at
one time.
ADSL Router Mode
Broadband Router Mode
H
Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
1. Power Connection
Plug the supplied power adapter to the wall
jack and the other side to the router.
Please note that the plug type may differ according to different country.

Billion BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
- 4-
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Giga Ethernet ports, and
the other side to the PC’s Ethernet interface.
3. EWAN Connection
Connect the supplied RJ-45 Ethernet cable to the Ethernet WAN port (EWAN), and
connect the other side to another alternative broadband device, such as Cable
Modem, VDSL, Fiber Modem or PON optic lines.
4. ADSL Connection
Connect the supplied RJ-11 phone cable to the router’s ADSL port, and the other
side to the phone jack on the wall.

Billion BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
- 5-
5. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct
high-frequency signals to the ADSL modem & low frequency signals to the
telephone or other analogue device to prevent inter-modulation distortion & get
good speed/stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
E
Ea as sy y S Si ig gn n- -O On n
Make sure that device is powered on, Ethernet cable is connected to your PC and ADSL line is
in sync. Then open up a web browser and you will automatically be directed to the step-by-step
easy sign on configuration wizard which will guide you to complete the basic network
configuration to connect to the internet.

Billion BiPAC 7800(N) (802.11n) Dual WAN ADSL2+ Firewall Router
- 6-
C
Co on nn ne ec ct ti in ng g t to o t th he e R Ro ou ut te er r
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
T
Tr ro ou ub bl le es sh ho oo ot ti in ng g
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of ADSL line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
P
Pr ro od du uc ct t S Su up pp po or rt t a an nd d C Co on nt ta ac ct t I In nf fo or rm ma at ti io on n
Most problems can be solved by referring to the Troubleshooting section in the user manual.If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
C
Co on nt ta ac ct t B Bi il ll li io on n
WORLDWIDE
http://www.billion.com
Billion Product Registration
Billion is committed to before and after sales customer services. You will get the most out of your Billion's products
after registration. Please register online at http://www.billion.com/register to receive valuable services and support
from us.
BiPAC
7
800
(N)
:
V1.0
1
EN