Billion BiPAC 6300NXL User manual

BiPAC 6300NX(L)
Fibre/4G LTE/Cable Gigabit
Wireless-N (VPN) Br adband
R uter
Quick Start Guide

Quick Start Guide

Billi n BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Br adband R uter
- 1-
Package C ntents
Billi n BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Br adband R uter
CD c ntaining the n-line manual
Ethernet (RJ-45) cable
Tw detachable antennas
P wer adapter
This Quick Start Guide
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.

D n t use the
r uter
in high humidity r high temperatu
res.
 D n t use the same p wer s urce f r the r uter as ther
equipment.
 D n t pen r repair the case y urself. If the r uter is t h t,
turn ff the p wer immediately and have it repaired at a qualified
service center.

Av id using this
pr duct
and all
access ries
utd rs.

Place the r uter n a stable surface.
 Only use the p wer adapter that c mes with the package. Using a
different v ltage rating p wer adapt r may damage the r uter.
Attention

Quick Start Guide
- 2-
Hardware Overview
The Fr nt LEDs
The Rear P rts
* N te 1. F r advanced reset and rest re setting, please refer t user manual.
.2. F r WPS c nfigurati n, please refer t the WPS secti n f user manual.
C nnect the sup
plied
p wer adapter t this
jack.
C nnect the
detachable antenna
When the system is ready,
the LED will be lit green;
lit red when the device
fails t b t.
C nnect the USB cable t
this p rt f r st rage service
and 3G/ 4G LTE USB m dem
backup f r Internet access.
Lit Green when c nnected
t an Ethernet device f r
1000Mbps. Lit Orange f r
10/100Mbps.
Lit green when the wirel
ess
c nnecti n is established.
Flashes when sending /
receiving data.
P wer
ON/OF
Push WPS butt n t
trigger Wi-Fi
Pr tected Setup.
*
2
Lit green when the
r uter is c nnected
t a 3G m dem r
USB device.
Lit
green when
transmissi n speed
hitting 1000Mbps; lit
range f r 10/100Mbps.
Lit green when IP c nnected
and IP traffic is passing. Lit
red when IP c nnected failed.
Lit ff when device in bridged
m de.
P
ress
the
“
Reset
”
butt n
6
sec nds r ab ve t rest re
fact ry default settings
.
*1
C nnect y ur c mputer
t a LAN p rt with the
Ethernet cable included.
Flash green when WPS c nfigurati n
is in pr gress; lit up brightly and then
g es ff in 5 sec nds when WPS is
established; flash f r 2 mins and then
g es ff when WPS establishment
failure.
Gigabit Ethernet WAN
p
rt
f r c nnecting t Cable
M dem, Fiber M dem r PON
ptic lines with RJ-45 cable.

Billi n BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Br adband R uter
- 3-
Hardware C nnecti n
3G/ 4G LTE R uter M del
Br adband R uter M del

Quick Start Guide
- 4-
Hardware Installati n
1. P wer C nnecti n
Plug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different countries.
2. LAN C nnecti n
Connect the supplied RJ-45 Ethernet ca le to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.
3. USB C nnecti n
(1) The USB 2.0 port supports 3G/ 4G LTE modem connectivity: users can
conveniently access Internet via 3G/,4G LTE eliminating the limitations of the
wired network. This solution also employs an auto fail-over feature to ensure
always-on connectivity for SOHO users.

Billi n BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Br adband R uter
- 5-
(2) Storage feature through USB 2.0 port: FTP server, SAMBA server.
4. EWAN C nnecti n
Connect RJ-45 Ethernet ca le to the EWAN p rt, and connect the other side to
another alternative road and device, such as Ca le Modem, VDSL, Fi re
Modem or PON optic lines.(Please refer t User Manual f r detail instructi n.)
C nnecting t the R uter
1. Open the we rowser and type http://192.168.1.254 in the rowser's address ox. This
num er is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”,
passw rd is “admin”. Press OK to proceed.
3. You will get a status report we page and main menu screen.
Please see the relevant secti ns f user manual f r detailed instructi ns n h w t
c nfigure y ur r uter.
Tr ublesh ting
1. N ne f the LEDs are n when y u turn n the r uter.
Check the connection etween the adapter and the router. If the error persists, you may have
a hardware pro lem. In this case you should contact technical support.
2. Can’t ping any PCs n the LAN.
Check the Ethernet LEDs on the front panel. The LED should e on for a port that has a PC
connected. If it is off, check the ca les etween your router and the PC. Make sure you have
uninstalled any software firewall for trou leshooting. Verify that the IP address and the su net
mask are consistent etween the router and the workstations.

Quick Start Guide
- 6-
Pr duct Supp rt and C ntact Inf rmati n
Most pro lems can e solved y referring to the Tr ublesh ting section in the User Manual. If
you cannot resolve the pro lem with the Tr ublesh ting chapter, please contact the dealer
where you purchased this product.
C ntact Billi n
WORLDWIDE
http://www. illion.com
BiPAC 6300NX(L) V1.00EN