Billy Goat F1002SPV User manual

FORCE SP BLOWER Owner’s Manual
Part No 440314 1 440314_G_HI
Patent #6,253,416 and other patents pending
FORCE BLOWER Owner's Manual
F1002SPV, F1302SPH, F1402SPV, F1802SPV
Beginning Serial #: 110215001
Accessories
Original Instructions
IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE
HOLD DOWN KIT
To secure blower for
transportation on trailer
floors.
P/N 440120
SOLID FRONT TIRE
Solid flat-free front tire.
P/N 440279
PARKING BRAKE
P/N 440140
CASTER KIT
For greater maneuverability
on hard surfaces.
P/N 440293
Effective and easy to use to
prevent blower from rolling.
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
2
CONTENTS
SPECIFICATIONS, SAFETY, AND INSTRUCTION LABELS 3
ENGINE LABELS AND PACKING CHECKLIST 4
ASSEMBLY_________ 5
OPERATION 6
MAINTENANCE 7-8
TROUBLESHOOTING_______ _____ _____9
MAINTENANCE RECORD____________ 10
ILLUSTRATED PARTS AND PARTS LIST _______________11-13
Go to http://www.billygoat.com for French-Canadian translations of the product manuals.
Visitez http://www.billygoat.com pour la version canadienne-française des manuels de
produits.
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
3
SPECIFICATIONS
F1002SPV F1302SPH F1402SPV F1802SPV
Engine HP
10.0 HP (6.6kW)
13.0 HP (9.6kW)
14.0 HP (10.4kW)
18 HP (13.42kW)
Engine Model
19L2320055F1
GX390UTQAA2
25V3320005F1
3564420298F1
Engine Type
B & S
VANGUARD
HONDA OHV
B & S VANGUARD
B & S VANGUARD
Engine Fuel Capacity
3.96 qt. (3.75L)
6.5 qt. (6.1L)
6.5 qt. (1.66L)
9 qt. (8.52L)
Engine Oil Capacity
0.88 qt. (0.83L)
1.16 qt. (1.1L)
1.0 qt. (0.95L)
1.75 qt. (1.66L)
Total Unit Weight
164 # (74.3 Kg)
167 # (75.7 Kg)
171 # (77.6Kg)
182 # (82.6 Kg)
Overall Length
58"(1.43m)
58"(1.43m)
58"(1.43m)
58"(1.43m)
Overall Width
29.25” (0.74m)
29.25” (0.74m)
29.25” (0.74m)
29.25” (0.74m)
Overall Height
45" (1.14m)
45" (1.14m)
45" (1.14m)
45" (1.14m)
Max Operating Angle
20o
20o
25o
25o
SAFETY
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which is known to the State
of California to cause cancer, and carbon monoxide, which is known to the State of California to cause
birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT®FORCETM Blower. If any labels are damaged or missing, replace
them before operating this equipment. For your convenience in ordering replacement labels, part numbers are included in the
Illustrated Parts List. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL READ OWNERS MANUAL LABEL SAFETY PROTECT DANGER FLYING DEBRIS
ITEM #44 P/N890301 ITEM# 45 P/N 100346 ITEM # 46 P/N 810736
LABEL EXPLOSIVE FUEL LABEL THROTTLE CONTROL
ITEM # 43 P/N 400268 ITEM # 42 P/N 810656
LABEL CLUTCH ENGAGE
P/N 500176
LABEL SPARK ARRESTOR
P/N 100252
LABEL OIL CHAIN
ITEM #119 P/N 830502
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
4
ENGINE LABELS
PACKING CHECKLIST
These items should be included in your carton. If any of these parts are missing, contact your dealer.
Your BILLY GOAT®FORCE Blower was shipped in one carton, completely assembled except for the Upper Handle Assembly
and Front Diverter. Mounting hardware for the Upper Handle Assembly can be found in the parts bag.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box as the Handle Assembly is attached to the unit by
cables.
PUT OIL IN ENGINE BEFORE STARTING.
Boxing Parts Checklist
Front Air Diverter
(For F1302H model only, P/N-
440045-5)
Handle Upper Assembly
Item #30 P/N-440035
Parts Bag & Literature Assy
P/N-440267
Honda 9 or 13 HP
B & S Vanguard 10, 14 or 18
HP
PARTS BAG & LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-440314, General Safety and Warnings Manual P/N-100294, Declaration of
Conformity P/N-440331, Handle Hardware-Items #10, #11, #74, #36, and #123.
HONDA
BRIGGS AND STRATTON VANGUARD
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
5
ASSEMBLY
1. The hardware for attaching the upper handle to the lower is in
the parts bag. Install the upper handle (item 30), to
preassembled lower handle (item 28) by sliding the upper
handle over and down the outside of the lower handle. Using
the bolts (items #36 and #123), washers (item #10) & lock nut
(item #11) to install upper handle to lower handle. NOTE: The
Pigtail bolt should go on the side that the pull start is on and the
open end should be facing down. Finish installing the other side
of the upper handle assembly using screw and lock nut
provided. (See Fig. 1)
2. The throttle control will be attached to the throttle arm on the
engine and wrapped around the engine for shipping. Unwrap
and secure throttle control (item #31) to upper handle with
screws (item #39). Screws will already be mounted in handle.
Simply remove and use to mount the throttle control. Secure the
throttle cable and clutch cable with two Ty-wraps. The Aim-and-
ShootTM is not attached. You will need to unroll the cable and
attach the ball end to the lever and seat the cable end into the
hole on the saddle clamp, with the cable running through the
slot. The clutch cable will also be wrapped up under the
machine. Route the cable under the axle and attach it by
removing the hitch pin and clevis pin and attaching it to the
clutch control lever. After it is attached pull on the cable and
slide it into the hole on the bracket so that it clicks into place. To
keep the cable from being damaged use two ty-wraps (item
#74) to secure it to the handle as shown, making sure that the
cable is not rubbing against the tire. NOTE: the cable should
be seated properly in the saddle and should follow the
contours of the handle. (See Fig. 2 and 3)
3. Connect spark plug wire.
Good routing
Bad routing
Fig. 1
Fig. 2
Fig. 3
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
6
OPERATION
Front
diverter
Squeeze
and fold
here
DRIVE LEVER:
To engage the clutch for forward motion, simply hold down the clutch
lever with your left hand while the engine is running; this will cause the
drive to engage and the machine will proceed to move forward.
Caution: It is not recommended to “feather” the drive. The drive
lever should be either fully engaged or fully disengaged. Failure to do so
can cause premature failure of the cone clutch in the transmission. This
type of failure will void the manufacturer’s warranty.
BLOWING OPERATION
Your Billy Goat Force blower is equipped with an air director cone and
the patented Aim-N-Shoot TM control lever to allow the operator to direct
the air stream up or down as required to assist in moving debris. This
feature is extremely useful when debris has piled up to the point that it
cannot be blown any farther. The air stream can be directed upward to
blow the top of the debris pile over and allow the operator to continue
moving more debris farther.
ADJUSTING AIR DIRECTOR
To adjust air direction, squeeze the Aim-N-Shoot control lever. When
you want to blow debris at the same angle for an extended period,
choose a suitable position and use the finger controlled push button lock
to lock the cone in position. For operations that do not require the use of
the Aim-N-Shootfeature the manual adjustment knob, pictured below,
can be used to permanently lock the cone into position.
CAUTION: Be sure to release the knob when returning to using the
Aim-N-Shoot.
DO NOT position director cone to where it will blow debris towards
people, vehicles or other objects in vicinity. Flying debris may damage,
harm, or cause injury to people or objects in air flow range.
FRONT DIVERTER POSITIONING (F13 models only)
The removable front diverter adapter can be slipped inside the cone to
direct the air stream forward. First turn off engine, and then simply
collapse and fold it into the larger opening of the diverter and slide inside
the cone allowing it to expand. Then position to the desired angle by
rotating the diverter. This option is extremely useful for cleaning out long
cracks in pavement or for cleaning under bushes, building overhangs or
along curbs. (See Fig. 4 and 5)
WARNING: Unit will be more difficult to control due to the air exiting
the unit. Keep hands on the unit at all times when using the front
diverter. Please note that the Aim-N-Shoot feature will not function when
the front diverter is installed.
Fig. 4
Manual
adjustment
knob
Fig. 5
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
7
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use
Daily or Every 5 Hours
Every 100-150 Hours
Inspect for worn or damaged parts

Check for excessive vibration

Check belt/chain tightness

Oil drive chain

Inspect impeller for cracks or damage

Inspect for loose parts

IMPELLER REMOVAL
1. Wait for engine to cool and disconnect spark plug.
2. Remove housing front cover by removing eleven bolts and nuts (items #13 & #14) around outside of front
cover.
3. Remove impeller bolt (item #35), lock washer (item #71) and washer (item #34).
4. DO NOT pry on impeller. Pull on center hub area of impeller only. Using a penetrating oil can help loosen a
stuck impeller.
5. Reinstall new impeller in reverse order of removal.
6. Tighten impeller bolt. Torque impeller bolt (see Parts List on page 13 for proper impeller bolt torque
specifications).
TIRE AIR PRESSURE
Check at regular intervals and maintain.
Front Tires - 24 Psi (165 kPa).
Rear Tires - 20 Psi (137 kPa).
BELT TENSION ADJUSTMENT
DO NOT adjust while the machine is running!
1. Wait for engine to cool and disconnect spark plug.
2. Loosen the nut (item #92) on the Idler pulley (item #93) but do not remove it. This should allow the pulley to slide left or
right. Once the pulley is at the proper distance to apply tension to the belt, tighten the nut. NOTE: Do not place too much
tension on the belt, as it will cause premature failure.
3. Reattach the spark plug.
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
8
DRIVE CHAIN REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Place a block of wood, or another object that will support and
steady the unit under the axle on the side of the machine you will
be working on.
3. Remove the two screws (item #103) holding the chain guard (item
#104) and then remove the chain guard.
4. Loosen the two nuts (item #98) holding the bearing (item #97).
(See Fig. 7)
5. Remove the retaining ring holding the wheel on and then slide the
wheel off.
6. Replace the chain (item #105). Remove the old chain by walking it
off the sprockets.
7. Position the bearing so that it applies the proper tension to the
chain and tighten the nuts holding the bearing NOTE: DO NOT
over tighten the chain, as this will cause premature failure.
Likewise, if the chain is too loose it will come off when the drive is
engaged.
8. Reassemble the machine using steps 1-4 in reverse order.
BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Follow the impeller removal steps (2-5 on page 8).
3. Remove the four bolts (item #8) holding the back plate (item 4) to
the back housing (item #6).
4. Loosen the nut on the idler pulley and slide it to the right to
relieve tension on the belt. (See Fig. 6)
5. Slip the belt (item #86) off the engine pulley and the transmission.
6 Replace the belt with a new one and slide the idler pulley to put
proper tension on the belt. NOTE: Do not place too much tension
on the belt, as it will cause premature failure.
7. Reassemble the machine in reverse order. NOTE: You will need
to replace the impeller bolt and torque to the proper specifications
see page 12. DO NOT use the old impeller bolt.
8. Reconnect spark plug wire.
CLUTCH CABLE ADJUSTMENT
1. With the machine off, loosen the two nuts on the end of the clutch cable (item #111) going in to the transmission.
2. By moving the position up or down on the threads it will change the tension on the clutch lever (item #113). NOTE: Do
not position it too high on the threads as this could cause the drive not to engage. Likewise, if it is placed too low the
drive may stay permanently engaged. The optimum setting is to remove any slack in the clutch cable when disengaged.
The travel of the clutch control will apply the correct spring force on the cone clutch. Once the desired position is in
place, tighten the nuts securely.
3. Start the machine and check the operation. If the drive cable is not engaging properly, shut the machine off and
reposition the nuts on the cable to tighten the drive cable.
Idler Pulley
Loosen nuts
Fig. 6
Fig. 7
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
9
TROUBLESHOOTING
*Using compressed air, or a backpack blower, you can
loosen or free debris easily from the impeller and housing,
which can cause wear and tear on the machine. You can
manually remove debris by taking off the front housing.
Note: Always disconnect the spark plug when servicing.
(See Fig. 8 and 9)
Fig. 8
Fig. 9
Problem Possible Cause Solution
Abnormal vibration Loose or out of balance impeller. Check impeller and replace if required.
Debris in impeller.
Clear debris with compressed air or a
backpack blower (see Fig. 8 and 9 below).*
Loose engine. Check engine.
Engine will not start Engine not in full choke position. Check choke position.
Out of gasoline or bad, old gasoline. Check gasoline.
Spark plug wire disconnected. Connect spark plug wire.
Gas valve off. Turn on gas valve.
Dirty air cleaner.
Clean or replace air cleaner. Contact a
qualified service person.
Engine is locked, will not pull
over
Engine problem.
Contact an engine servicing dealer for
engine problems.
Aim-N-ShootTM lever sticking Debris stuck around cone. Clean debis.
Cone adjustment knob too tight.
Apply silicone based lubricant to
Adaptor mount nut (item #38) too
pivot points.
tight. Loosen manual adjustment knob.
Loosen nut.
No self propelling Drive lever not engaged. Engage drive lever.
Drive belt worn or broken. Check drive belt.
Drive chain off the sprockets. Check drive chain.
Drive cable is out of adjustment. Check drive cable (see page 9).
Self-propelled drive will not
release
Improper drive cable adjustment, or
cable is kinked.
Check the drive cable (see page 9).
Noisy or broken chain No chain or lubrication. Lubricate chain.
Chain tension. Check drive chain (see page 9).
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
10
MAINTENANCE RECORD
Date
Service Performed
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
11
FORCETM SP PARTS DRAWING
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
12
FORCETM SP PARTS LIST
F1302SPH F1402SPH F1002SPV F1802SPV
ITEM NO. DESCRIPTION PART NUMBER QTY. PART NUMBER QTY. PART NUMBER QTY. PART NUMBER QTY.
1 ENGINE 13 HP HONDA GX390 440018 1 - - - - - -
ENGINE, VANGUARD 400 - - 440346 1 - - - -
ENGINE 10HP VANGUARD - - - - 440342 1 - -
ENGINE 18 VANGUARD - - - - - - 812240 1
2 BASE ENGINE WA FSP 440244-S 1 440244-S 1 440244-S 1 440244-S 1
3 GUARD BELT UPPER FSP 440209 1440209 1440209 1440209 1
4 PLATE REINFORCE HOUSING 440010-P 1 440010-P 1 440010-P 1 440010-P 1
5 HOUSING FRONT MOLDED 440023 1440023 1440023 1440023 1
6 HOUSING BACK MOLDED 440024 1440024 1440024 1440024 1
7 WASHER LOCK 3/8 S/T MED 8177012 48177012 48177013 58177013 4
8 SCREW CAP 3/8-16X2 ZP 8041054 48041054 48041054 48041054 4
9 ROD HAND STOP 440057 1440057 1440057 1440057 1
10 WASHER 5/16 FLATWASHER Z/P 8171003 14 8171003 14 8171003 14 8171003 14
11 NYLON INSERT LOCKNUT 5/16-18 8160002 11 8160002 11 8160002 11 8160002 11
12 SCREWCAP 5/16-18 X1.75 ZP 8041031 48041031 4 - - 8041031 2
SCREWCAP 5/16"-18 X2 3/4" GR 5 HCS ZP - - - - 8041034 - -
13 SCREWCAP 1/4-20 x 1 1/2 8041008 11 8041008 11 8041008 11 8041008 11
14 NUT FLANGE 1/4-20 900455 15 900455 15 900455 15 900455 15
15
WHEEL & TIRE 13" X5" PNEUMATIC SPROCKET
440219 2440219 2440219 2440219 2
16 RING RETAINING 3/4 850230 2850230 2850230 2850230 2
17 SCREW SM 1/4" X3/4" TYPE AB HXWF 8122082 78122082 78122082 7 - -
18 WHEEL ASSY 10 " PNEUMATIC 400295 1400295 1400295 1400295 1
19 SPACER FRONT AXLE 440220 1440220 1440220 1440220 1
20 SPACER LH WHEEL FRONT 440224 1440224 1440224 1440224 1
21 SPACER RH WHEEL FRONT 440221 1440221 1440221 1440221 1
22 SCREWCAP 1/2-13 x 9 1/2" 8041240 18041240 18041240 18041240 1
23 WASHER FLAT 1/2" SAE 8172011 28172011 28172011 28172011 2
24 WASHER W/BOLT WA 440075 1440075 1440075 1440075 1
25 KNOB 3/8-16 SOLID HUB 811230 1811230 1811230 1811230 1
26 WASHER 2.25 OD x .515 ID x .134 ZP 610308-P 1 610308-P 1 610308-P 1 610308-P 1
27 BRACKET HOLDER WA 440240 1440240 1440240 1 - -
28 HANDLE LOWER 440034 1440034 1440034 1440034 1
29 NYLON INSERT LOCKNUT 1/2-13LT WT TH ZP 8161044 18161044 18161044 18161044 1
30 ASSY FORCE UPPER W/GRIPS/DECALS 440030 1440030 1440030 1440030 1
31 CONTROL THROTTLE 440013 1440013 1440013 1440013 1
32 CABLE THROTTLE CONTROL 440014 1440014 1440014 1440178 1
33 NUT LOCK 3/8-16 LT WT THIN ZP 8161042 38161042 38161042 38161042 3
34 WASHER 1.5 O.D.X0.45 I.D. X 0.5 440176 1440176 1440176 1440176 1
35 SCREWCAP 3/8-24 X3.5 GR. 8 (38 +/-2 ft-lbs.) 440151 1 - - - - - -
SCREWCAP 7/16-20 X3.5 GR.8 (60 +/-2 ft-lbs) - - 440150 1440150 1 - -
SCREWCAP 3/8-24 X4 GR.8 (38 +/-2 ft-lbs) - - - - - - 8042062 1
36 SCREWCAP 5/16"-18 X2" ZP 8041032 18041032 18041032 18041032 2
37 DIRECTOR CONE 5" 440044-S 1 440044-S 1 - - - -
DIRECTOR CONE 4" - - - - 440046-S 1 - -
DIRECTOR CONE 6" - - - - - - 440170-S 1
38 DIVERTOR FRONT 440045-5 1 440045-5 1 440045-4 1 - -
39 SCREW SM #10-24X1/2" DRILL POINT 8122064 28122064 28122064 28122064 2
40 IMPELLER ASSEMBLY 17" 440236 1440236 1440236 1 - -
IMPELLER SERVICE ASSY FORCE 18HP - - - - - - 440162 1
41 GRILL FRONTBLOWER 440067-1-S 1 440067-1-S 1 440067-1-S 1 440171-S 1
42 LABEL THROTTLE CONTROL 810656 1810656 1810656 1810656 1
43 LABEL FUEL EN/SP - - - - 100261 1100261 1
45 LABEL SAFETY PROTECT READ MANUAL 100346 1100346 1100346 1100346 1
46 LABEL DANGER FLYING DEBRIS 810736 1810736 1810736 1810736 1
48 LABEL FORCE 440269 1440269 1440269 1440269 1
49 HANDLE ASSY 440104 1440104 1440104 1440104 1
50 KEY 1/4" SQ x 3 1/4 9201128 1 - - 9201128 1 - -
KEY 1/4" SQ x 3 3/4 - - 9201130 1 - - 9201130 1
51 SCREWCAP 1/4-20 X1" HCS ZP - - - - - - 8041006 5
52 WASHER FLAT 1/4 - - - - - - 8171002 5
53 NUT LOCK 1/4"-20 HEXZP 8160001 18160001 18160001 18160001 6
54 HANDLE DIVERTER FORCE 440119 1440119 1440119 1440119 1
55 PIN LATCH DIVERTER 440118 1440118 1440118 1440118 1
56 SPRING COMPRESSION 0.281 X 0.88 440129 1440129 1440129 1440129 1
57 RING RETAINING .122 DIA 440125 1440125 1440125 1440125 1
58 SADDLE LOWER DIVERTER 440115 1440115 1440115 1440115 1
59 PLATE LOCK DIVERTER 440116 1440116 1440116 1440116 1
60 SCREW PLASTITE #6-19 X 5/8" 440126 1440126 1440126 1440126 1
61 SADDLE UPPER DIVERTER 440114 1440114 1440114 1440114 1
62 SCREW PLASTITE #10-14 X 1" 440132 2440132 2440132 2440132 2
63 PIN PIVOT DIVERTER CONTROL 440123 1440123 1440123 1440123 1
64 RING RETAINING 5/16 430327 1430327 1430327 1430327 1
65 CABLE ASSY 440117 1440117 1440117 1440117 1
66 DIVERTER PIVOT ADAPTOR 440121 1440121 1440121 1440121 1
67 SPRING EXTENSION 0.468 X5.25 440130 1440130 1440130 1440130 1
68 BRACKET DIVERTER FORCE 440212 1440212 1440212 1440212 1
NOT FOR REPRODUCTION

FORCE SP BLOWER Owner’s Manual
Part No 440314 440314_G_HI
13
FORCETM SP PARTS LIST
F1302SPH F1402SPH F1002SPV F1802SPV
ITEMNO. DESCRIPTION PART NUMBER QTY. PART NUMBER QTY. PART NUMBER QTY. PART NUMBER QTY.
69 PIN CLEVIS 1/4 X3/4 440124 2440124 2440124 2440124 2
70 HITCH PIN CLIP .051 X3/4" 440193 2440193 2440193 2440193 2
71 WASHER LOCK 3/8 S/T MED 8177012 18177012 18177012 18177012 1
WASHER LOCK 7/16 S/TMED - - - - - - - -
72 ADAPTOR MOUNT WA 440122 1440122 1440122 1440122 1
73 GRIP 1-1/4" ID x9.5" LONG 440146 2440146 2440146 2440146 2
74 TY-WRAP 900407 4900407 4900407 4900407 4
75 WASHER .765 ID X1.25 OD X0.6" 850238 2850238 2850238 2850238 2
76 FORCE WHEEL BEARING .751 ID 440055 2440055 2440055 2440055 2
77 GUARD MANIFOLD - - - - - - 812243 1
78 GUARD MUFFLER SW - - - - - - 812410 1
80 SPACER PLATE WELDMENT - - - - 440148 1 - -
81 ROLL PIN 8195096 18195096 18195096 18195096 1
82 SPACER REAR WHEEL SP 440225 2440225 2440225 2440225 2
83 PLUG 791056 2791056 2791056 2791056 2
84 CARRIAGE BOLT 3/8"-16 X1 3/4" ZP 8024061 58024061 58024061 58024061 5
85 SPACER ENGINE FACE 440174 1440174 1440174 1440174 1
86 BELT 3L29 440215 1440215 1440215 1440215 1
87 SPACER HUB 1" ID X1.25" W/PULLEY 440213 1440213 1440213 1 - -
SPACER HUB 1" ID X1.25" W/PULLEYFSP18 - - - - - - 440214 1
88 CARRIAGE BOLT 3/8-16 X5" ZP 8024161 18024161 18024161 18024161 1
89 TUBE SPACER .625" OD X.357 LONG 440228 1440228 1440228 1440228 1
90 GUARD BELT LOWER FSP 440210 2440210 2440210 2440210 2
91 SCREW PLASTITE 1/4-10 X3/4 HWH ZP 840082 6840082 6840082 6840082 6
92 BOLT 1/4"-20 X1/2" SER FLANGE - - - - - - 812381 2
93 PULLER VIDLER 2.5 510137 1510137 1510137 1510137 1
94 WASHER 1.00" OD X.380 SQ HOLE 440227 1440227 1440227 1440227 1
96 CARRIAGE BOLT 1/4"-20 X3/4" 8024021 48024021 48024021 48024021 4
97 BEARING 1/2" STEEL PRESSED HOUSING 891025 2891025 2891025 2891025 2
99 KEYWOODRUFF 1/8" X1/2" 510180 2510180 2510180 2510180 2
100 SPROCKET 8 TOOTH 891022 2891022 2891022 2891022 2
101 RETAINING RING 1/2" 350146 2350146 2350146 2350146 2
102 SPROCKET 32T #43 1.594 BORE 440218 2440218 2440218 2440218 2
103 SCREW SELF TAP 1/4"-20 X5/8" 890359 4890359 4890359 4890359 6
104 CHAIN GUARD LH 440206-S 1 440206-S 1 440206-S 1 440206-S 1
CHAIN GUARD RH 440207-S 1 440207-S 1 440207-S 1 440207-S 1
105 CHAIN #43X44 PITCHES 440217 2440217 2440217 2440217 2
108 TRANS SINGLE SPEED W/CLUTCH 440216 1440216 1440216 1440216 1
109 WASHER 3/8" SAE 8172009 28172009 28172009 28172009 2
111 CLUTCH CABLE FORCE SP 440243 1440243 1440243 1440243 1
113 CLUTCH CONTROL ARM 440277 1440277 1440277 1440277 1
114 CLUTCH CONTROL BRACKET 440245 1440245 1440245 1440245 1
115 GRIP CLUTCH CONTROL FSP 440242 1440242 1440242 1440242 1
117 SPARK ARRESTOR LABEL 100252 1100252 1100252 1100252 1
118 SPRING LEVER GZ 610429 1610429 1610429 1610429 1
119 LABEL OIL CHAIN 830502 2830502 2830502 2830502 2
120 LABEL DANGER 900327 2900327 2900327 2900327 2
121 NUT LOCK 5/16-24 SER HEXWSHR FLNG 440274 8440274 8440274 8440274 8
122 LABEL CLUTCH DRIVE 500176 1500176 1500176 1500176 1
123 EYEBOLT PIGTAIL 5/16"-18 X1 1/4" 440280 1440280 1440280 1440280 1
125 DIVERTER ASSY 440312 1440312 1440312 1440312 1
126 LABEL AIMAND SHOOT 440332 1440332 1440332 1440332 1
NOT FOR REPRODUCTION