Billy Goat BC2601EU Hydro Series User manual

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 1 501533_-_HI
BC2601EU Hydro Series Brush Cutter
Owner’s Manual
Beginning Serial #: 100515001
Original Instructions
IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 2 501533_-_HI
CONTENTS
SPECIFICATIONS ______________________________________________ 3
INSTRUCTION LABELS __________________________________________ 4
ASSEMBLY INSTRUCTIONS ____________________________________ 5-6
OPERATION _________________________________________________ 7-8
MAINTENANCE AND BATTERY MAINTENANCE__________________ 9-12
TROUBLESHOOTING ___________________________________________13
ILLUSTRATED PARTS LIST ___________________________________ 14-21
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 3 501533_-_HI
BC2600EU SERIES SPECIFICATIONS
BC2601HHC
Engine Type
Honda GXV390
Model Number
GXV390UT1 DABG
Displacement
390 cc
Fuel Capacity
2.2 qt (2.1 L)
Oil Capacity
1.2 qt (1.1L)
Unit Weight
325 lb (147.4 kg)
Overall Length
80 in (2.03 m)
Overall Width
31 in (0.78 m)
Overall Height
48 in (1.21 m)
Maximum Operating Slope
20o
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 4 501533_-_HI
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT®Euro Hydro-Drive Brush Cutter. If any labels are damaged or
missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are
provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to
the Figure and Item numbers shown.
ENGINE LABELS
PN 100261
(Item 61) PN 100346 (Item 134)
PN 810736
(Item 136)
PN 501512
(Item 165)
PN 900327
(Item 20) PN 500177
(Item 135)
PN 501502
(Item 85) PN 400424
(Item 5)
PN 501504
(Item 139)
PN 500168
(Item 140)
PN 100256
(Item 62)
Honda
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 5 501533_-_HI
Brush Cutter Assembly Drawing
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 6 501533_-_HI
PACKING CHECKLIST
Your BILLY GOAT®BCHydro-Drive Brush Cutter was shipped in one carton, completely assembled except for the upper handle
assembly and the front caster bracket mount. Mounting hardware for the handle and caster bracket mount can be found in the
parts bag. The throttle cable hardware is located on the bracket on the right side of the handle.
NOTE: A CB18, C50, SC50 or MCB50 series dry or wet battery with a 17.2 Ah rating is required when replacing the battery.
READ all safety instructions before assembling unit.
PARTS BAG & LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-501533, General Safety and Warranty Manual P/N-100296, Declaration of
conformity P/N-501506
ASSEMBLY
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 14-21.
1. REMOVE unit from carton and check the contents of the parts bag with the list above.
2. REMOVE mounting hardware from the hardware bag.
3. ATTACH the handle to the engine base with the items 72, 73, and 48.
4. TIGHTEN mounting hardware on handle braces (items 5 and 6).
5. ATTACH the throttle (82) to the right hand bracket (item 70) using the hardware items 83 and 84. Tighten securely and
make sure the cable isn’t binding.
6. ATTACH the Blade drive cable to the lever and seat the plastic insert into the bracket on the left side of the handle.
7. SECURE the drive and blade cables with the ty-wraps provided.
8. ATTACH the caster bracket frame to the deck with the clip (item 164), make sure the clip section snaps completely
around the neck of the yoke.
9. RECONNECT spark plug wire.
DISCONNECT spark plug wire before assembling unit.
Boxing Parts Checklist
Owner’s Manual 501533
Upper Handle Assembly, P/N 501010, Electric model P/N 501009
Ty-Wraps (4 ea)
Screwcap 3/8” – 16 X 2” P/N 8041054 (qty 4)
Washer 3/8” flat P/N 8171004 (qty 4)
Nut Lock 3/8”-16 P/N 8160003 (qty 4)
Nut lock #10-24 hex P/N 8164005 (qty 2)
Screw machine flat HD Phil P/N 830514 (qty 2)
Spring pin clevis P/N 501318 (qty 1)
Engine Manual Per Model
Honda
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 7 501533_-_HI
OPERATION
OPERATOR CONTROLS
The operator’s station is at the rear of the machine between the handlebars. The operator should STAND in a position to allow
both handlebars to be grasped firmly and which allows sufficient leverage to steer the machine. Operator’s controls are shown
below.
Operator Control Locations
1 Blade Clutch Lever
2 Forward Lever 5 Pull Starter
3 Reverse Lever 6 Choke
4 Throttle
STARTING ENGINE
CHECK engine oil level before operating machine.
DO NOT START equipment with drive or blade clutch engaged.
3
1
4
2
5
6
1. Place equipment on a level, firm surface that is free of rocks or other debris.
2. Place throttle in “fast” position. (See Fig. 1)
3. Pull choke out (See Fig. 2 Honda engine only).
4. Units equipped with manual starters: Pull starter rope to start engine. NOTE:
PULL STARTER CORD slowly until resistance is felt. Then pull cord rapidly to
avoid kickback. (See Fig. 3)
5. Push choke in (Honda engine only).
6. Pull throttle control back to and allow engine to reach correct operating speed.
Fig. 1
Fig. 2
Fig. 3
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 8 501533_-_HI
CUTTING OPERATION
1. Press blade clutch handle down (See Fig. 4) to engage blade. Allow
blade to spin up to normal operating speed.
2. Pull Forward (See Fig. 5) or Reverse Drive lever (See Fig. 6) up to
engage transaxle in desired direction.
DECK HEIGHT ADJUSTMENT
1. To raise and lower the cutting height on the deck, pull the knob upwards
and rotate the handle clockwise to raise the cutting height and counter-
clockwise to lower the cutting height. DO NOT ADJUST HEIGHT WITH
THE BLADE RUNNING
CLEARING ACLOGGED DECK
DISCONNECT spark plug wire before servicing unit.
1. Shut engine off and wait for blade to stop completely.
2. Disconnect spark plug wire.
3. Remove clog from cutting deck.
WEAR durable gloves. Clog may contain sharp materials.
4. Reconnect spark plug wire.
SHUT DOWN
1. Release drive lever (Fig. 5/6) to disengage transaxle.
2. Release blade clutch handle (Fig. 4) to disengage blade.
3. Move the throttle to the slowest possible position on the throttle control.
*****TIPS*****
The best performance is achieved when cutting in dry conditions. The quality of the cut is directly related to ground speed during
cutting. Under most conditions cutting should be done at a slower ground speed. Fast speeds should be reserved for conditions
where weeds and brush are thinned out or not very tall. If the quality of the cut is not satisfactory, attempt at slower speeds.
Fig. 4 Left Handle
Fig. 5 Right Handle
Fig. 6 Left Handle
Fig. 8 Freewheel Lever
NEUTRAL/FREEWHEEL
1. Identify the freewheel lever located in front of the right front
wheel when viewing from operator’s station.
2. Pull lever to initiate freewheel motion.
3. Push lever in to initiate driver enabled motion.
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 9 501533_-_HI
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every
Use
Daily or Every
5 Hours
Every 25
Hours
Every 50
Hours
Every 100-
150 Hours
Inspect for worn or damaged parts

Check for excessive vibration

Inspect for loose parts

Sharpen blade. Note: nut will need to be
replaced when blade is removed

Inspect belts for wear

Lubricate throttle control cable and linkage

Check blade clutch cable tension

Inspect battery for corrosion, damage or
leaks (electric start units only)

Apply anti-seize compound to rear axles

Check battery strap for excessive wear or rips

Replace blade drive and transaxle drive belts

If transmission is topped off or refilled, SAE 10w30 grade, non-detergent oil should be poured through the port covered by the
black cap. Approx. 2.2 liters of oil will be needed to reach this level. This is dependent on the amount of residual oil remaining
in case after draining. Draining of old oil must be done through the same port (covered with the black plug) by inverting
transaxle.
COMMON REPLACEMENT PARTS
Blade. P/N 501221. Original equipment replacement blade.
Transaxle Drive Belt. P/N 501268. Original equipment replacement drive belt.
Blade Drive Belt. P/N 501220. Original equipment replacement drive belt.
Throttle Control Assembly. Throttle control including cable.
CLEANING
Your BILLY GOAT®Brush Cutter should be cleaned periodically to ensure optimum performance and service life. Clogs and
debris should be removed from the blade area and debris should be removed from the engine cooling fins. A garden hose or
pressure washer may be used for cleaning.
DO NOT SPRAY WATER DIRECTLY ON THE BLADE CLUTCH WHEN USING A POWER
WASHER. SEE FIG 7.
Fig. 7
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 10 501533_-_HI
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 14-21.
BLADE SHARPENING AND REMOVAL
READ all safety instructions before servicing unit.
1. Disconnect spark plug wire.
2. Lift and support front of unit to allow access to underside.
UNIT IS HEAVY. Make sure support is adequate to support weight of machine.
3. Block blade to prevent it from rotating during removal.
4. Remove blade bolt (item 23), and friction washer (item 39).
5. Remove blade (item 2) and install replacement blade. NOTE: When sharpening blade make sure to sharpen all cutting
edges. If the lock nut is removed and replaced more than once, it should be replaced with a new lock nut (P/N 8160009).
When replacing the blade use BILLY GOAT Industries PN 501224 only.
6. Attach new blade with new blade bolt (item 23), and new friction washer (item 39) removed earlier included with your
new blade. NOTE: Inspect fasteners for wear and replace if necessary.
7. Torque blade bolt to 40 ft-lbs.
8. Reconnect spark plug wire.
BLADE DRIVE BELT TENSION
NOTE:The Blade Drive belt is under constant tension by the idler arm on the deck.
DISCONNECT spark plug wire before servicing unit.
1. Disconnect spark plug wire.
2. Loosen four screws (item 27) holding belt deck cover (item 29) and remove the cover.
3. Examine condition of belt and amount of tension on belt.
4. If the idler is not providing enough tension inspect the spring (item 50) attaching it to the spindle base. If not enough
tension is being put on the arm, replace the spring.
5. Replace engine base door (item 29) and secure with screws removed earlier.
6. Reconnect spark plug wire.
7. Check belt tension by operating unit under conditions that caused belt slippage. If belt continues to slip it may require
replacement before operation may continue.
BLADE CLUTCH ADJUSTMENT
DISCONNECT spark plug wire before servicing unit.
DISCONNECT spark plug wire before servicing unit.
If clutch continues to slip or squeal, do not operate equipment until adequate adjustment or repair
has been performed. Improper adjustment can cause clutch to overheat and slip, greatly reducing
performance and clutch life.
1. Disconnect spark plug wire.
2.
As the clutch/brake wears or begins slipping or squealing, adjustment may be
required to maintain proper cable tension and clutch engagement. A properly
adjusted blade clutch should require 10 lbs. of force to depress the end of the
clutch lever. The blade clutch cable spring should stretch 1/4” to 3/8” (6.4-9.5
mm).
3. Adjust cable tension by tightening or loosening cable adjustment nut on rear
of engine base (see Fig. 8). Be sure to leave enough slack in cable to allow
blade brake to engage.
4. Reconnect spark plug wire.
Fig. 8
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 11 501533_-_HI
NOTE: See Fig 11 for proper belt routing.
TRANSAXLE DRIVE BELT REMOVAL AND REPLACEMENT
BLADE DRIVE BELT REMOVAL AND REPLACEMENT
Belt Routing Diagram
(Top View of Machine)
DISCONNECT spark plug wire before servicing unit.
DISCONNECT spark plug wire before servicing unit.
Blade Drive Belt (with Transaxle
Belt not Shown)
LOOKING THROUGH TOP
Transaxle Drive Belt
(Seated below drive belt on
clutch)
1. Disconnect spark plug wire.
2. Lift and support the rear of the unit to allow access to the underside.
3.
Detach the spring (item 50) from the bracket (item 98) that is keeping
tension on the drive belt. (See Fig. 9)
4.
Walk the belt (item 121) off of the clutch (item 54) by slowly pulling the
engine over. WARNING:
use caution not to pinch fingers between the belt
and clutch.
5. Slip the belt off of the transaxle pulley.
6. Replace the belt in reverse order. NOTE: make sure the belt is seated
properly in the clutch and transaxle and make sure that it does not bend over
the fan blades on the transaxle.
1. Disconnect spark plug wire.
2. Lift and support rear of unit to allow access to underside.
UNIT IS HEAVY. Make sure support is adequate to support
weight of machine.
3.
Loosen the four screws (item 27) holding deck belt cover (item 29) and
remove cover.
4. Follow the steps 3 and 4 in the Transaxle drive belt removal section to
remove the Transaxle drive belt. NOTE: It may be necessary to pry idler
pulley (item 35) away from its original position to release belt, using a
ratchet with an extension in the square hole on the idler arm should allow
the proper leverage to pull it off the belt. (See Fig. 10)
5.
Relieve the tension on the blade belt by pulling the deck idler arm off of the
belt. Then walk the belt off of the deck pulley.
6. Feed the belt back to the engine base then slip the belt off of the clutch.
7. Install the new belt in reverse order making sure the belt is seated properly
in the clutch.
8. Reconnect spark plug wire.
Fig. 9
Fig. 10
Fig. 11
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 12 501533_-_HI
TRANSAXLE DRIVE ADJUSTMENT
DISCONNECT spark plug wire before servicing unit.
DECREASE
INCREASE
1. Disconnect spark plug wire.
2.
Adjustments to cable tension are made at the barrel entering the
Drive Control Levers.
3. Adjust cable tension by tightening or loosening cable adjustment
barrel on rear of engine base (see below).
NOTE: Moving the cable adjustment barrel OUT increases tension.
Moving the barrel IN decreases tension. Increasing the tension too
much will cause the drive to stay engaged whereas not enough will
cause it not to engage when the lever is pulled.
4. Reconnect spark plug wire.
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 13 501533_-_HI
TROUBLESHOOTING
Problem
Possible Cause
Corrective Action
Engine will not start
Throttle is set to Slow/Stop position.
Move throttle to fast position.
Out of gasoline.
Fill gas tank.
Old or contaminated gasoline.
Drain gas tank and fill with fresh
gasoline.
Spark plug wire disconnected.
Connect spark plug wire.
Dirty air cleaner.
Clean or replace air cleaner.
Will not cut or cutting performance is
poor
Blade drive cable tension incorrect.
Adjust blade drive cable tension.
Dull blade.
Sharpen or replace blade. Note: nut will
need to be replaced when blade is
removed.
Clogged deck.
Unclog deck.
Excessive debris built up on or blocking
blade.
Clear debris from blade area.
Engine RPM set too low.
Check engine RPM.
Abnormal vibrations
Blade loose or out of balance.
Check blade for tightness. Rebalance if
necessary.
Engine loose.
Check engine mounting bolts.
Blade drive belt worn.
Replace blade drive belt.
Belt slips or smokes
Belt tension too low.
Adjust belt tension.
Belt worn or stretched.
Replace belt.
Pulleys worn or damaged.
Replace pulleys.
Clutch slips or squeals
Clutch cable tension too low.
Replace spring on idler arm.
Clutch worn or damaged.
Replace worn or defective clutch
assembly parts.
Blade brake will not engage
Inadequate slack in clutch cable.
Adjust clutch cable.
Clutch worn or damaged.
Replace clutch/brake assembly.
Transaxle will not engage
Clutch lever not engaging clutch.
Adjust clutch cable.
Clutch cable defective.
Replace cable.
Belt worn or broken.
Replace belt.
Transaxle will not disengage
Clutch cable out of adjustment.
Adjust clutch cable.
Engine will not turn over
Defective blade clutch.
Replace clutch.
Engine problem.
Contact an authorized servicing dealer
for your engine.
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 14 501533_-_HI
BC26EU HYDRO-DRIVE DECK PARTS DRAWING
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 15 501533_-_HI
BC26EU HYDRO-DRIVE DECK PARTS LIST
ITEM
NO
DESCRIPTION
BC2601HHC
Part No
QTY
1
SCREWCAP 3/8-24 X 1” HCS GR. 8
900154
1
2
BLADE 26” FLAT BC26
501224
1
3
WASHER DECK RETAINNG
501214
1
4
LABEL BADGING BC26 HYDRO
501500
1
5
LABEL DANGER
400424
4
7
BOLT CARRIAGE 5/16”-18 X 3/4” ZP
8024039
6
8
NUT LOCK 5/16-18 ZP
8160002
15
9
WASHER 1.125” OD X 0.344” ID X .25” THK
441150
2
12
BUSHING FLANGED 1.250” X 0.380” ID
501316
1
13
CARRIAGE BOLT 5/16”-18 X 1”
8024040
5
14
PLATE FRONT DEFLECTOR
501319
1
15
RUBBER DEFLECTOR FRONT
501320
1
16
HEIGHT ADJUST HANDLE ASSY
501124
1
17
DECK INTAKE WA EURO BC26
501123
1
18
CASTER FRAME WA
501125
1
19
DECK BC26EU WA W/LABELS
501121-S
1
20
LABEL DANGER GUARD
900327
1
21
SCREW SER HEX WASHER FLNG
791080
6
22
SCREWCAP 3/8”-16 X 1 1/4” HCS ZP
8041051
1
23
SCREWCAP 9/16”-18 X 1 3/4” GR 8
501345
1
24
PULLEY 7” OD X 1.000 BORE
501308
1
26
BELT 6972 POWERATED
501220
1
27
SCREW SELT TAP 1/4-20 X 5/8” HWH TYPE F
890359
4
28
LABEL PRODUCT DECAL LG CIRCLE
430303
1
29
COVER BELT DECK WA BC26 W/LABEL
501602
1
30
PIN COTTER 1/8” X 1”
8197031
1
31
WASHER .765 ID X 1.25 OD X .06 THK
850238
1
32
WASHER LOCK 3/8 S/T MED
8177012
1
33
WASHER 1.5 OD X .453 ID X .25 THK
440153
1
34
TUBE PIVOT IDLER VQ
830526
1
35
PULLEY IDLER 4.00 OD X 3/8” BORE
500113
1
36
BUSHING PIVOT FRAME AE
360183
1
37
ARM IDLER DECK WA BC
501103
1
38
ZERK FITTING GREASE
610363
3
39
WASHER BLADE BC26
501346
1
41
SPACER SPINDLE BEARING BC26
501245
1
43
BEARING, BALL 1641 - 2RS-PRX
501302
2
44
BUSHING 1.500 ID X 1.5 LONG FLANGED
501217
2
45
BRACKET DECK MOUNT WA BC26 W/LABEL
501604
1
46
SHAFT BLADE BC26
501341
1
47
WASHER 3/8” SAE
8172009
1
48
NUT LOCK 3/8-16 HEX
8160003
4
49
ARM RTN WA BC26
501116
2
50
SPRING LIFT ASSIST TENSION
351254
2
51
SCREWCAP 3/8”-16 X 3 3/4” HCS ZP
8041061
1
52
BUSHING PIVOT LIFT
360138
1
53
NUT LOCK 3/8”-16 LT WT TH ZP
8161042
1
78
SCREWCAP 5/16”-18 X 1” GR 5 HCS ZP
8041028
2
79
WASHER LOCK 5/16” S/T MED
8177011
2
94
BOLT SHOULDER 1/2” X 2”
520031
2
136
LABEL WARNING FLYING DEBRIS
810736
1
157
KEY 1/4 SQ. X 0.75”
9201109
2
158
SPRING IDLER BC
501261
1
162
CASTER RIGHT SIDE WA
501126
2
163
TIRE WHEEL ASSY
501333
2
164
SPRING PIN CLEVIS
501318
1
165
LABEL HEIGHT ADJUST EURO BC26
501512
1
166
CASTER LEFT SIDE WA
501127
1
167
YOKE FEMALE STEEL 3/8”-24 RH X 2.50
501317
1
168
NUT LOCK 3/8”-24 ZP THIN HT
8161022
1
175
ADAPTER BLADE WA BC26
501343
1
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 16 501533_-_HI
BC26EU HYDRO-DRIVE ENGINE PARTS DRAWING
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 17 501533_-_HI
BC26EU HYDRO-DRIVE ENGINE PARTS LIST
ITEM
NO
DESCRIPTION
BC2601HHC
Part No
QTY
1
SCREWCAP 3/8-24 X 1” HCS GR. 8
900154
1
3
WASHER DECK RETAINING
501214
1
8
NUT LOCK 5/16”-18 ZP
8160002
2
11
ENGINE BASE WA W/LABELS
501603
1
27
SCREW SELT TAP 1/4-20 X 5/8” HWH TYPE
F
890359
4
32
WASHER LOCK 3/8” S/T MED
8177012
1
54
CLUTCH
501223-S
1
55
WASHER LOCK S/T MED
8177013
1
56
SCREWCAP 7/16”-20 X 3 1/2” GR 8
W/PATCH
440150
1
58
ENGINE 13 HP HONDA PULL GXV390UT1
DABG
501358
1
59
SCREWCAP 5/16”-18 X 1 3/4 HCS ZP
8041031
2
60
WASHER 5/16” FLAT
8171003
4
61
LABEL WARNING FUEL
100261
1
62
LABEL SPARK ARRESTOR
100256
1
63
PLATE CHOKE BC26
500325
1
64
SCREWCAP 5/16-24 X 1” GR 8 ZP W/PATCH
400164
2
65
SCREWCAP 5/16”-18 X 2” HCS ZP
8041032
2
66
NUT FLANGE 5/16”-18 ZP
350346
4
67
SCREW SER HEX WSHR FLNG 5/16-18 X
3/4”
351264
4
68
GUARD REAR HYDRO BC26
501295
1
80
CABLE CLUTCH
501279
1
132
LABEL MADE IN USA
520116
1
134
LABEL SAFETY PROTECT READ MANUAL
100346
1
159
PIN CLEVIS 0.25 X 0.050
440124
1
160
PIN HITCH CLIP 0.051 X 3/4
440193
1
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 18 501533_-_HI
BC26EU HYDRO-DRIVE HANDLE PARTS LIST
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 19 501533_-_HI
BC26EU HYDRO-DRIVE HANDLE PARTS LIST
ITEM
NO
DESCRIPTION
BC2601HHC
Part No
QTY
8
NUT LOCK 5/16-18 ZP
8160002
3
48
NUT LOCK 3/8-16 HEX
8160003
8
69
HANDLE LOWER LEFT
501400
1
70
BRACKET THROTTLE BC26
501251
2
72
SCREWCAP 3/8”-16 X 2”
8041054
4
73
WASHER 3/8” FLAT
8171004
16
74
BOLT SHOULDER 3/8”-16 X 1 1/2”
501313
1
75
SCREWCAP 3/8”-16 X 3” HCS ZP
8041058
4
76
WASHER 1/4” FLAT
8171002
2
77
BOLT CARRIAGE 5/16”-18 X 1 1/2” ZP
8024042
2
78
SCREWCAP 5/16”-18 X 1” ZP
8041028
2
79
WASHER LOCK 5/16” S/T MED
8177011
2
80
CABLE CLUTCH
501279
1
81
LEVER CONTROL BLADE
500312
1
82
CONTROL THROTTLE
440013
1
83
NUT LOCK LT #10-24 HEX
8164005
2
84
SCREW MACHINE FLAT HD PHIL #10-24
830514
2
85
LABEL DRIVE DIRECTION
501502
1
86
PLUG TUBE INSERT 1.25” OD
791056
4
87
GRIP HANDLE
500267
2
88
GUARD HAND BC26
501215
2
89
CONTROL MAGURA
351209
2
90
GRIP LEVER 0.125” X 1” X 5” RED
500379
1
91
HANDLE UPPER
501402-S
1
92
HANDLE LOWER RIGHT
501401
1
107
CABLE SPEED CONTROL RT SERVICE
501276-S
1
130
CABLE SPEED CONTROL LFT SERVICE
351271-S
1
135
LABEL BLADE ENGAGE
500177
1
LABEL THROTTLE PULL START BC
501314
1
138
CABLE THROTTLE
440014
1
NOT FOR REPRODUCTION

BC26EU HYDRO-DRIVE Owner’s Manual
Part No 501533 20 501533_-_HI
BC26EU HYDRO-DRIVE TRANS PARTS DRAWING
NOT FOR REPRODUCTION