Billy Goat HYDRO-DRIVE BC26 User manual

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 1501531_A_HI
BC2601 Mechanical Drive Series Brush Cutter
Owner’s Manual
Beginning Serial #: 040616001
Original Instructions
IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 2 501531_A_HI
CONTENTS
SPECIFICATIONS AND SAFETY 3
INSTRUCTION LABELS 4
ASSEMBLY INSTRUCTIONS 5-6
OPERATION 7-8
MAINTENANCE AND BATTERY MAINTENANCE 9-12
TROUBLESHOOTING 13
ILLUSTRATED PARTS LIST 14-21
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 3 501531_A_HI
BC 2600 SERIES SPECIFICATIONS
BC2601HM BC2601HMF
B2601HMFT
Engine Type Honda GXV390 Honda GXV390
Model Number GXV390UT1 DABG GXV390UT1 DABG
Displacement 390 cc 390 cc
Fuel Capacity 2.2 qt (2.1 L) 2.2 qt (2.1 L)
Oil Capacity 1.2 qt (1.1L) 1.2 qt (1.1L)
Unit Weight 316 lb (147.4 kg) 326 lb (147.4 kg)
Overall Length 72 in (1.83 m) 72 in (1.83 m)
Overall Width 31 in (0.78 m) 31 in (0.78 m)
Overall Height 48 in (1.21 m) 48 in (1.21 m)
Maximum Operating Slope 20o20o
SAFETY
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which is known to the State
of California to cause cancer, and carbon monoxide, which is known to the State of California to cause
birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Read the safety rules and follow them closely. Failure to obey these rules could result in loss of control of
the unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 4 501531_A_HI
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT®Mechanical Drive Brush Cutter. If any labels are damaged or
missing, replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are
provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to
the Figure and Item numbers shown.
ENGINE LABELS
PN 100261
(Item 88) PN 100346 (Item 68)
PN 810736
(Item 76)
PN 100256
(Item 123)
PN 900327
(Item 122) PN 500177
(Item 86)
PN 501503
(Item 74) PN 400424
(Item 53)
PN 500168
(Item 72)
Honda
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 5 501531_A_HI
Brush Cutter Assembly Drawing
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 6 501531_A_HI
PACKING CHECKLIST
Your BILLY GOAT®BC Self-Propelled Mechanical Drive Brush Cutter was shipped in one carton, completely assembled except
for the upper handle assembly and the front guard bar. Mounting hardware for the handle and guard bar is temporarily installed
on the lower handle and the front of the deck assembly. The throttle cable hardware is located on the bracket on the right side of
the handle
READ all safety instructions before assembling unit.
PARTS BAG & LITERATURE ASSY
Warranty Card- P/N 400972, Owner’s Manual- P/N 501531, General Safety and Warnings Manual- P/N 100296, Declaration of
conformity P/N 100502
ASSEMBLY
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 14-21.
1. Remove unit from carton and check the contents of the parts bag with the list above.
2. Remove mounting hardware from the hardware bag.
3. Attach the handle to the engine base with the items 62, 97, and 119.
4. Tighten mounting hardware on handle braces (items 5 and 6).
5. Attach guard bar (item 16) to Skid bar by installing the side bolts into the top two holes on the skids with items 103, 104
and 116.
6. Attach the throttle (30) to the right hand bracket (item 27) using the hardware (items 63 and 64). Tighten securely and
make sure the cable isn’t binding.
7. Attach the Blade drive cable to the lever and seat the plastic insert into the bracket on the left side of the handle.
8. Secure the drive and blade cables with the ty-wraps provided.
9. Place the shifter cable (item 41) into the bracket on the lower handle (item 14) with the nuts on both sides of the bracket.
10. Then attach the upper part of the cable to the shifter lever (item 21) using the nut located on the end of it and tighten
securely. Then tighten the two nuts on the bracket where it was seated in step 9. Check to make sure the lever has full
travel. If the lever does not have full travel loosen the nuts and either raise or lower them on the barrel to provide the
proper travel for the lever. NOTE: Putting too much tension on the cable can cause excess wear on the cable and lead
to failure. Likewise, if the cable is loose it will result in poor shifting.
11.Reconnect spark plug wire.
DISCONNECT spark plug wire before assembling unit.
Boxing Parts Checklist
Owner’s Manual P/N 501531
Upper Handle Assembly, P/N 501010
Guard Bar, P/N 501403
Ty-Wraps (4 ea)
Screwcap 3/8” – 16 X 2” P/N 8041054 (qty 4)
Washer 3/8” flat P/N 8171004 (qty 4)
Nut Lock 3/8”-16 P/N 8160003 (qty 4)
Nut lock #10-24 hex P/N 8164005 (qty 2)
Screw machine flat HD Phil P/N 830514 (qty 2)
Washer 5/16” flat P/N 8171003 (qty 4)
Bolt carriage 5/16”-18 x 1 3/4” P/N 8024043 (qty 4)
Nut Lock 5/18”-18 hex ZP P/N 8160002 (qty 4)
Engine Manual Per Model
Honda
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 7 501531_A_HI
OPERATION
OPERATOR CONTROLS
The operator’s station is at the rear of the machine between the handlebars. The operator should STAND in a position to allow
both handlebars to be grasped firmly and which allows sufficient leverage to steer the machine. Operator’s controls are shown
below.
Operator Control Locations
1 Blade Clutch Lever 5 Choke
2 Forward Lever 6 Pull Starter
3 Speed/direction shifter
4 Throttle
STARTING ENGINE
CHECK engine oil level before operating machine.
DO NOT START equipment with drive or blade clutch engaged.
1
3
6
4
2
5
1. Place equipment on a level, firm surface that is free of rocks or other debris.
2. Place throttle in “fast” position. (See Fig. 1)
3. Pull choke out (See Fig. 2, Honda engine only).
4. Pull starter rope to start engine. (See Fig. 3) NOTE: PULL STARTER CORD slowly
until resistance is felt. Then pull cord rapidly to avoid kickback.
5. Push choke in (Honda engine only).
6. Pull throttle control back to and allow engine to reach correct operating speed.
Fig. 1
Fig. 2
Fig. 3
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 8 501531_A_HI
CUTTING
OPERATION
1. Select the desired direction and speed. (See Fig. 4)
2. Press blade clutch handle down (See Fig. 5) to engage blade. Allow
blade to spin up to normal operating speed.
3. Pull Up on the drive lever (See Fig. 6) to engage the transaxle in the
desired direction.
CLEARING ACLOGGED DECK
DISCONNECT spark plug wire before servicing unit.
1. Shut engine off and wait for blade to stop completely.
2. Disconnect spark plug wire.
3. Remove clog from cutting deck.
WEAR durable gloves. Clog may contain sharp materials.
4. Reconnect spark plug wire.
SHUT DOWN
1. Release drive lever (Fig. 6) to disengage transaxle.
2. Release blade clutch handle (Fig. 5) to disengage blade.
3. Move the throttle to the slowest possible position on the throttle control.
*****TIPS*****
The best performance is achieved when cutting in dry conditions. The quality of the cut is directly related to ground speed during
cutting. Under most conditions cutting should be done at a slower ground speed. Fast speeds should be reserved for conditions
where weeds and brush are thinned out or not very tall. If the quality of the cut is not satisfactory, attempt at slower speeds.
Fig. 4 Left Handle
Fig. 6 Right Handle
Fig. 5 Left Handle
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 9 501531_A_HI
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation Every Use Daily or Every
5 Hours
Every 25
Hours
Every 50
Hours
Every 100-
150 Hours
Inspect for worn or damaged parts. 
Check for excessive vibration 
Inspect for loose parts. 
Sharpen blade. Note: the nut will need to
be replaced when blade is removed

Inspect belts for wear. 
Lubricate throttle control cable and
linkage.

Check blade clutch cable tension. 
Apply anti-seize compound to rear axles. 
Replace blade drive and transaxle drive
belts.

COMMON REPLACEMENT PARTS
•Blade. P/N 501224. Original equipment replacement blade.
•Transaxle Drive Belt. P/N 501221. Original equipment replacement drive belt.
•Blade Drive Belt. P/N 501220. Original equipment replacement drive belt.
•Skid. P/N 501407. Side deck skid.
•Throttle Control Assembly. Throttle control including cable.
CLEANING
Your BILLY GOAT ®Brush Cutter should be cleaned periodically to ensure optimum performance and service life. Clogs and
debris should be removed from the blade area and debris should be removed from the engine cooling fins. A garden hose or
pressure washer may be used for cleaning.
DO NOT SPRAY WATER DIRECTLY ON THE BLADE CLUTCH WHEN USING A POWER
WASHER. SEE FIG. 7.
Fig. 7
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 10 501531_A_HI
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 14-21.
BLADE SHARPENING AND REMOVAL (See pages 14 and 15 for Parts Illustration and Parts List)
READ all safety instructions before servicing unit.
1. Disconnect spark plug wire.
2. Lift and support front of unit to allow access to underside.
UNIT IS HEAVY. Make sure support is adequate to support weight of machine.
3. Block blade to prevent it from rotating during removal. When replacing the blade, use BILLY GOAT Industries PN 501224
only. NOTE: When sharpening blade make sure to sharpen all cutting edges. If the lock nut is removed and replaced more
than once, it should be replaced with a new lock nut (P/N 8160009).
4. Remove blade bolt (item 37), and friction washer (item 35).
5. Remove blade (item 45) and install replacement blade.
6. Attach new blade with new blade lock bolt (item 37), and new friction washer (item 35) removed earlier included with your
new blade. NOTE: Inspect fasteners for wear and replace if necessary.
7. Torque blade lock nut to 40 ft-lbs.
8. Reconnect spark plug wire.
BLADE DRIVE AND TENSION (See pages 14 and 15 for Parts Illustration and Parts List)
NOTE: The blade drive belt is under constant tension by the idler arm on the deck
DISCONNECT spark plug wire before servicing unit.
1. Disconnect spark plug wire.
2. Loosen two screws (item 75) holding belt deck cover (item 29) and remove the cover.
3. Examine condition of belt and amount of tension on belt.
4. If the idler is not providing enough tension inspect the spring (item 58) attaching it to the spindle base. If not enough
tension is being put on the arm, replace the spring.
5. Replace engine base door (item 29) and secure with screws removed earlier.
6. Reconnect spark plug wire.
7. Check belt tension by operating unit under conditions that caused belt slippage. If belt continues to slip it may require
replacement before operation may continue.
BLADE CLUTCH ADJUSTMENT (See pages 16 and 17 for Parts Illustration and Parts List)
DISCONNECT spark plug wire before servicing unit.
DISCONNECT spark plug wire before servicing unit.
If clutch continues to slip or squeal, do not operate equipment until adequate adjustment or repair has been
performed. Improper adjustment can cause clutch to overheat and slip, greatly reducing performance and
clutch life.
1. Disconnect spark plug wire.
2. As the clutch/brake wears or begins slipping or squealing, adjustment may
be required to maintain proper cable tension and clutch engagement. A
properly adjusted blade clutch should require 10 lbs. of force to depress the
end of the clutch lever. The blade clutch cable spring should stretch 1/4” to
3/8” (6.4-9.5 mm).
3. Adjust cable tension by tightening or loosening cable adjustment nut on rear
of engine base (see Fig. 8). Be sure to leave enough slack in cable to allow
blade brake to engage.
4. Reconnect spark plug wire.
Fig. 8
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 11 501531_A_HI
NOTE: See Fig 11 for proper belt routing.
TRANSAXLE DRIVE BELT REMOVAL AND REPLACEMENT (See pages 20 and 21 for Parts Illustration and Parts List)
BLADE DRIVE BELT REMOVAL AND REPLACEMENT (See pages 14 and 15 for Parts Illustration and Parts List)
LOOKING THROUGH TOP
Belt Routing Diagram
(Top View of Machine)
DISCONNECT spark plug wire before servicing unit.
Blade Drive Belt (with Transaxle
Belt not Shown)
Transaxle Drive Belt
(Seated below drive belt on
clutch)
1. Disconnect spark plug wire.
2. Lift and support the rear of the unit to allow access to the underside
3. Detach the spring (item 43) from the bolt (item 107) that is keeping tension
on the drive belt. (See Fig. 9)
4. Walk the belt (item 22) off of the clutch (item 3) by slowly pulling the engine
over. WARNING: use caution not to pinch fingers between the belt and
clutch.
5. Slip the belt off of the transaxle pulley.
6. Replace the belt in reverse order. NOTE: make sure the belt is seated
properly in the clutch and transaxle and make sure that it does not bend over
the fan blades on the transaxle.
1. Disconnect spark plug wire.
2. Lift and support rear of unit to allow access to underside.
UNIT IS HEAVY. Make sure support is adequate to support weight
of machine.
3. Loosen the two screws (item 75) holding deck belt cover (item 29) and
remove cover.
4. Follow the steps 3 and 4 in the Transaxle drive belt removal section to
remove the Transaxle drive belt. NOTE: It may be necessary to pry idler
pulley (item 18) away from its original position to release belt, using a ratchet
with an extension in the square hole on the idler arm should allow the proper
leverage to pull it off the belt. (See Fig. 10)
5. Relieve the tension on the blade belt by pulling the deck idler arm off of the
belt. Then walk the belt off of the deck pulley.
6. Feed the belt back to the engine base then slip the belt off of the clutch.
7. Install the new belt in reverse order making sure the belt is seated properly in
the clutch.
8. Reconnect spark plug wire
Fig. 10
Fig. 9
Fig. 11
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 12 501531_A_HI
TROUBLESHOOTING
Problem Possible Cause Corrective Action
Engine will not start Throttle is set to Slow/Stop position. Move throttle to fast position.
Out of gasoline. Fill gas tank.
Old or contaminated gasoline. Drain gas tank and fill with fresh
gasoline.
Spark plug wire disconnected. Connect spark plug wire.
Dirty air cleaner. Clean or replace air cleaner.
Blade drive cable tension incorrect. Adjust blade drive cable tension.
Will not cut or cutting performance is
poor
Dull blade. Sharpen or replace blade. Note: nut will
need to be replaced when blade is
removed.
Clogged deck. Unclog deck.
Excessive debris built up on or blocking
blade.
Clear debris from blade area.
Engine RPM set too low. Check engine RPM.
Abnormal vibrations Blade loose or out of balance. Check blade for tightness. Rebalance if
necessary.
Engine loose. Check engine mounting bolts.
Blade drive belt worn. Replace blade drive belt.
Belt slips or smokes Belt tension too low. Adjust belt tension.
Belt worn or stretched. Replace belt.
Pulleys worn or damaged. Replace pulleys.
Clutch slips or squeals Clutch cable tension too low. Replace spring on idler arm.
Clutch worn or damaged. Replace worn or defective clutch
assembly parts.
Blade brake will not engage Inadequate slack in clutch cable. Adjust clutch cable.
Clutch worn or damaged. Replace clutch/brake assembly.
Transaxle will not engage Clutch lever not engaging clutch. Adjust clutch cable.
Clutch cable defective. Replace cable.
Belt worn or broken. Replace belt.
Transaxle will not disengage Clutch cable out of adjustment. Adjust clutch cable.
Engine will not turn over Defective blade clutch. Replace clutch.
Engine problem. Contact an authorized servicing dealer
for your engine.
DECREASE
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 13 501531_A_HI
BC26 MECHANICAL DRIVE DECK PARTS DRAWING
124
61
2
26
4
17
19
53
16
35
5
37
45
34
32
33
15
14
6
38
11
18
58 59
51
57
32
110
77
121
94
80
117
97
113
69
116
102
101
93 81
76
108
104
116
103
103 112
103
116
124
126
4
35
37
34
32
33
11
57
32
110
77
121
124
124
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 14 501531_A_HI
BC26 MECHANICAL DRIVE DECK PARTS LIST
Item no. Description P/N Qty P/N Qty P/N Qty
2BASE ENGINE BC26 FIXED WA W/LABELS 501120-S 1501120-S 1501120-S 1
4BRACKET DECK MOUNT WA BC 501118 1501118 1501118 1
5SKID BC26 501407 2501407 2501407 2
6ARM IDLER DECK WA BC 501103 1501103 1501103 1
11 PULLEY 7" OD X 1.00" BORE 501308 1501308 1501308 1
14 PLATE CLAMP SKIRTING BC26 501239 3501239 3501239 3
15 DEFLECTOR RUBBER BC26 501231 1501231 1501231 1
16 BAR GUARD BC26 501403 1501403 1501403 1
17 HINGE DEFLECTOR BC26 501211 1501211 1501211 1
18 PULLEY IDLER 4.00" OD X 3/8" BORE 500113 1500113 1500113 1
19 DECK WA W/LABELS BC26 501102-S 1501102-S 1501102-S 1
26 BELT 6972 POWERATED 501220 1501220 1501220 1
32
BEARING, BALL 1641 - 2RS-PRX 501302 2501302 2501302 2
33 ADAPTER BLADE WA BC26 501343 1501343 1501343 1
34 SHAFT BLADE BC2600 501341 1501341 1501341 1
35 WASHER BLADE BC26 501346 1501346 1501346 1
37 SCREWCAP 9/16"-18 X 1 3/4" GR 8 501345 1501345 1501345 1
38 BUSHING PIVOT LIFT 360138 2360138 2360138 2
45 BLADE 26" FLAT BC26 501224 1501224 1501224 1
51 BUSHING PIVOT FRAME AE 360183 2360183 2360183 2
53 LABEL DANGER 900327 4900327 4900327 4
57 SPACER SPINDLE BEARING BC2600 501245 1501245 1501245 1
58 SPRING IDLER 501261 1501261 1501261 1
59 TUBE PIVOT IDLER VQ 830526 1830526 1830526 1
61 SPINDLE ASSEMBLY, BC FIXED DECK 501609 1501609 1501609 1
69 WASHER .765" ID X 1.25" OD X .06" 850238 2850238 2850238 2
76 LABEL DANGER FLYING DEBRIS 810736 1810736 1810736 1
77 WASHER 1.5 OD X .453 ID X .25 THK 440153 1440153 1440153 1
80 PIN COTTER 1/8" X 1" 8197031 18197031 18197031 1
81 LABEL OUTBACK BC26 MECH 501501 1501501 1501501 1
93 BOLT CARRIAGE 1/4"-20 X 3/4" ZP 8024021 78024021 78024021 7
94 SCREWCAP 3/8"- 16 X 3 3/4" HCS ZP 8041061 18041061 18041061 1
97 NUT LOCK 3/8"-16 HEX 8160003 11 8160003 11 8160003 11
101 SER HEX WSHR FLNG SCR .375" - 16 X .75" 791080 6791080 6791080 6
102 BOLT CARRIAGE 5/16"-18 X 1" ZP 8024040 98024040 98024040 9
103 WASHER 5/16" FLAT ZP 8171003 18 8171003 18 8171003 18
104 BOLT CARRIAGE 5/16"- 18 X 1 1/4" ZP 8024041 48024041 48024041 4
108 NUT LOCK 1/4"-20 HEX ZP 8160001 78160001 78160001 7
110 WASHER LOCK 3/8" S/T MED 8177012 18177012 18177012 1
112 SCREWCAP 5/16"-18 X 1 1/2" HCS ZP 8041030 68041030 68041030 6
113 NUT LOCK 3/8"- 16 LT WT TH ZP 8161042 28161042 28161042 2
116 NUT LOCK 5/16"-18 HEX ZP 8160002 26 8160002 26 8160002 26
117 WASHER 3/8" SAE 8172009 28172009 28172009 2
121 SCREWCAP 3/8"-16 1 1/4" HCS ZP 8041051 18041051 18041051 1
124 KEY 1/4" SQ X 3/4" 9201109 29201109 29201109 2
126 BLA DE PULLEY A ND A DA PTER KIT SERV ICE 501611 1501611 1501611 1
BC2601HM
BC2601HMF
BC2601HMFT
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 15 501531_A_HI
BC26 MECHANICAL DRIVE ENGINE PARTS DRAWING
56
109
103
114
99
89
97
117
105
106
84 73
107
116 85
85
97
83
75
116
31
10
43
7
3
22
26
29
28 2
1
88
122
123
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 16 501531_A_HI
BC26 MECHANICAL DRIVE ENGINE PARTS LIST
Item no. Description P/N QTY P/N QTY
1ENGINE 13 HP HONDA PULL GXV390UT1 DABG 501358 1501358 1
2BASE ENGINE BC26 FIXED WA W/LABELS 501120-S 1501120-S 1
3CLUTCH 501223-S 1501223-S 1
7BRACKET BELT TIGHTEN BC26 501249 1501249 1
10 ARM IDLER DRIVE MECH WA 501117 1501117 1
22 BELT 6830 POWERATED 501268 1501268 1
26 BELT 6972 POWERATED 501220 1501220 1
28 LABEL PRODUCT DECAL LG CIRCLE 430303 1430303 1
29 DOOR BASE ENGINE BC 500233 1500233 1
31 PULLEY IDLER ARM HP 521121 1521121 1
43 SPRING TRANS IDLER 510142 1510142 1
56 CABLE CLUTCH BC26 501279 1501279 1
73 BOLT SHOULDER 1/2" X 2" 520031 1520031 1
75 SER HEX WSHR FLNG SCR 5/16"-18 X 3/4" 351264 4351264 4
83 BOLT CARRIAGE 5/16"-18 X 3/4" ZP 8024039 28024039 2
84 SCREWCAP 7/16" -20 X 3 1/2" GR. 8 W/PATCH 440150 1440150 1
85 NUT JAM 1/4" NC HEX 8143001 28143001 2
88 LABEL WARNING FUEL EN/SP - - - -
89 PIN CLEVIS .25 X .050 440124 1440124 1
97 NUT LOCK 3/8"-16 HEX 8160003 11 8160003 11
99 PIN, RUE RING 0.250" 371275 1371275 1
103 WASHER 5/16" FLAT ZP 8171003 18 8171003 18
105 SCREWCAP 3/8"-16 X 2" HCS ZP 8041054 18041054 1
106 WASHER LOCK 7/16" S/T MED 8177013 18177013 1
107 SCREWCAP 1/4"-20 X 1 3/4" HCS ZP 8041009 18041009 1
109 SCREW 3/8" X1 1/2" TCS 850408 1850408 1
SCREWCAP 5/16"- 24 X 1" GR. 8 ZP W/PATCH 400164 2400164 2
114 SCREWCAP 5/16"- 18 X 1 3/4" GR. 5 HCS ZP 8041031 28041031 2
116 NUT LOCK 5/16"-18 HEX ZP 8160002 26 8160002 26
117 WASHER 3/8" SAE 8172009 28172009 2
122 LABEL GUARDS 900327 1900327 1
123 LABEL SPARK ARRESTOR 100256 1100256 1
124 DETACHABLE BALL JOINT 831615 1831615 1
BC2601HM
BC2601HMF & BC2601HMFT
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 17 501531_A_HI
BC26 MECHANICAL DRIVE HANDLE PARTS DRAWING
2
9
42
14
50
20
27 63
65
30
64
56
39 2421
38
25 49
55
40
41
78
119 97
119
62
91
119
115
118
111
100
116
74
120 97
113
86
116
90
79
125
119
124
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 18 501531_A_HI
BC26 MECHANICAL DRIVE HANDLE PARTS LIST
Item no. Description P/N QTY P/N QTY
2BASE ENGINE BC26 FIXED WA W/LABELS 501120-S 1501120-S 1
9GUARD REAR BC26 501298 1501298 1
14 LOWER MECH BC HANDLE W/BRACKET 501115 1501115 1
20 HANDLE LOWER RIGHT 501401 1501401 1
21 LEVER SHIFTER WA BC26 501107 1501107 1
24 GRIP LEVER 1" X 4.25" 840191 1840191 1
25 LEVER CONTROL BLADE LIGHT 500312 1500312 1
27 BRACKET THROTTLE BC26 501251 1501251 1
30 CONTROL THROTTLE 440013 1440013 1
38 BRACKET SHIFTER WA W/LABELS 501108-S 2501108-S 2
39 CONTROL LEVER DRIVE HP 521104 1521104 1
40 GRIP HANDLE 1" X 5.5" 500267 2500267 2
41 CABLE CONTROL SHIFTER BC26 501254 1501254 1
42 PLUG TUBE INSERT 1.25 OD 791056 4791056 4
49 GRIP LEVER 0.125" X1" X 5" ORANGE 500379 1500379 1
50 HANDLE UPPER 501402-MS 1501402-MS 1
55 GUARD HAND BC26 501215 2501215 2
56 CABLE CLUTCH BC26 501279 1501279 1
62 SCREWCAP 3/8"- 16 X 2" 8041054 48041054 4
63 SCREW MACH #10 - 24 FLAT HD 830514 2830514 2
64 NUT LOCK LT #10 - 24 HEX 8164005 28164005 2
65 CABLE THROTTLE 31.5" - - - -
CABLE THROTTLE CONTROL 25.5 440014 1440014 1
74 LABEL SHIFT BC26 MECH 501503 1501503 1
78 SCREW SELT TAP 1/4"-20 X 5/8 HWH TYPE F 890359 4890359 4
79 LABEL THROTTLE 501314 1501314 1
86 LABEL CLUTCH BLADE 500177 1500177 1
90 BOLT SHOULDER 1/2" X 1" 500114 1500114 1
91 SCREWCAP 3/8"-16 X 3" HCS ZP 8041058 88041058 8
97 NUT LOCK 3/8"-16 HEX 8160003 11 8160003 11
100 BOLT SHOULDER 3/8"- 16 X1 1/2" 501313 1501313 1
111 BOLT CARRIAGE 5/16"- 18 X 1 1/2" ZP 8024042 28024042 2
113 NUT LOCK 3/8"- 16 LT WT TH ZP 8161042 28161042 2
115 WASHER LOCK 5/16" S/T MED 8177011 68177011 6
116 NUT LOCK 5/16"-18 HEX ZP 8160002 26 8160002 26
118 SCREWCAP 5/16"- 18 X 1" 8041028 28041028 2
119 WASHER 3/8" FC 8171004 16 8171004 16
120 NUT LOCK 1/4"- 28 TH ZP 8161020 18161020 1
125 CABLE DRIVE BC26 SERVICE 501282-S 1501282-S 1
BC2601HM
BC2601HMF & BC2601HMFT
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 19 501531_A_HI
BC26 MECHANICAL DRIVE TRANS PARTS DRAWING
2
22
54
12 60
47
44
13
36
46
48
41
8
23
115
68 70
72
93
87
108
92
69
71
82
75
75
82 98
109
96 95
82
NOT FOR REPRODUCTION

BC26 MECHANICAL DRIVE Owner’s Manual
Part No 501531 20 501531_A_HI
BC26 MECHANICAL DRIVE TRANS PARTS LIST
Item no. Description P/N QTY P/N QTY
2BASE ENGINE BC26 FIXED WA 501120-S 1501120-S 1
8WHEEL 16" STUD TREAD W/CENTERED HUB 500366 2 - -
WHEEL 16" STUD TREAD FOAM FILLED - - 500371 2
12 BRACKET ANTI ROTATION 501338 2501338 2
13 PULLEY 5" OD "A" SEC 501248 1501248 1
22 BELT 6830 POWERATED 501268 1501268 1
23 BAR SH IFT T AXL E 501255 1501255 1
36 BRACKET BELT FINGER BC26 501252 1501252 1
41 CABLE CONTROL SHIFTER BC26 501254 1501254 1
44 GROMMET 1.25" HOLE 520092 1520092 1
46 GUIDE BELT RH BC 501253 1501253 1
47 KEY 3/16" SQ X 2 1/8" 9201087 29201087 2
48 BRACKET SHIFTER LOWER BC26 501283 1501283 1
54 TRANSAXLE 3 SPD W/REV 521102 1521102 1
60 RING RETAINING "E" 3/4" 850230 2850230 2
68 LABEL SAFETY PROTECT READ MANUAL 100346 1100346 1
69 WASHER .765" ID X1.25" OD X .06" 850238 2850238 2
70 LABEL MADE IN USA 520116 1520116 1
71 RING SNAP TRUARC 5/8" 850233 1850233 1
72 LABEL CHOCK WHEEL 500168 2500168 2
75 SER HEX WSHR FLNG SCR 5/16"-18 X 3/4" 351264 4351264 4
82 SCREW SELF TAP 5/16" X 3/4" HEX 8123128 48123128 4
87 SCREW MACHINE #10-24 X 3/4" WF ZP 8059136 28059136 2
92 NUT LOCK #10-24 HEX 8155007 28155007 2
93 BOLT CARRIAGE 1/4"-20 X 3/4" ZP 8024021 78024021 7
95 WASHER LOCK 1/4" EXTERNAL TOOTH 8181007 18181007 1
96 WASHER 1/4" SAE 8172007 18172007 1
98 SCREWCAP 5/16"-18 X 2 3/4" HCS ZP 8041035 48041035 4
108 NUT LOCK 1/4"-20 HEX ZP 8160001 78160001 7
109 SCREW 3/8" X 1 1/2" TCS 850408 1850408 1
SCREWCAP 5/16"- 24 X 1" GR. 8 ZP W/PATCH 400164 2400164 2
115 WASHER LOCK 5/16" S/T MED 8177011 68177011 6
BC2601HM
BC2601HMF & BC2601HMFT
NOT FOR REPRODUCTION