Billy Goat PR550 Installation instructions

Part No. 350177 Form No. F021604B
Page 1 of 16
Thank You for Selecting
Operator Owner's Manual
The Powerful PR and OS
POWER RAKES and OVERSEEDERS
Specifications
FLAIL BLADES
P/N 35 186.
A complete replacement set. 52
of our high uality flail blades for
your PR. Includes 8 new lock
clips for replacement installa-
tion.
PR55 , PR55 H, PR55 V,
PR55 HV, OS55 , OS55 H
FLAIL SHAFTS
P/N 35 185.
A full set of four shafts for
replacement. Includes 8 new
lock clips for replacement
installation.
Note: We recommend
replacing the shafts when you
replace flails.
REPLACEMENT PARTS
DRIVE BELT
P/N 35 116.
Original E uipment drive belt for
your PR.
SLICING REEL
P/N 35 113.
A complete verti-slicing reel for
your PR. 20" wide reel for use
in grasses that re uire vertical
cutting, and for assisting in lawn
overseeding projects.
ACCESSORIES
SLICING BLADES
P/N 35 187.
A full set of twenty blades for
replacement. Includes 40 new
capscrews, and lock nuts for
replacement installation.
21
3
SPACER BUMPERS
P/N 35 258.
A complete replacement set.
44 of 1/2" spacer bumpers
and 4 of 1/4" spacer bumpers
OVERSEEDER KIT
P/N 35 281 / 35 282.
The new Overseeding Kit is
constructed of all 12 gauge
steel with two lift handles on
each side to assist in lifting the
entire unit and easily converts a
PR Series Power Rake into an
overseeder with 4 bolts and
minimal tools.
NOTE: Overseeder Conversion
Kit (350282) includes Slicing
Reel (350113). Part No.
(350281) comes with the
Overseeder Box only.
NEW
PR550 PR550V PR550H PR550HV OS550 OS550H
ENGINE: H.P. 5.5 (4.1 kW) 5.5 (4.1 kW) 5.5 (4.1 kW) 5.5 (4.1 kW) 5.5 (4.1 kW) 5.5 (4.1 kW)
ENGINE: TYPE B&S OHV B&S OHV HONDA OHV HONDA OHV B&S OHV HONDA OHV
ENGINE: FUEL CAP. 3.0 qt. (2.84 L) 3.0 qt. (2.84 L) 3.88 qt. (3.6 L) 3.88 qt. (3.6 L) 3.0 qt. (2.84 L) 3.88 qt. (3.6 L)
ENGINE: OIL CAP. 0.66 qt. (0.62 L) 0.66 qt. (0.62 L) 0.69 qt. (0.65 L) 0.69 qt. (0.65 L) 0.66 qt. (0.62 L) 0.69 qt. (0.65 L)
WEIGHT: UNIT 160# (72.5 kg) 163# (74.1 kg) 158# (71.8 kg) 161# (73.2 kg) 206# (93.4 kg) 204# (92.5 kg)
WEIGHT: SHIPPING 183# (83.0 kg) 183# (83.0 kg) 178# (80.9 kg) 178# (80.9 kg) 229# (104.1 kg) 230# (104.5 kg)
ENGINEWEIGHT: 36# (16.3 kg) 36# (16.3 kg) 34# (15.4 kg) 34# (15.4 kg) 36# (16.3 kg) 34# (15.4 kg)
MAX. ENGINEOPERATING SLOPE 15° 15° 20° 20° 15° 20°

Part No. 350177 Form No. F021604BPage 2 of 16
IN THE INTEREST OF SAFETY
THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY
DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.
BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & EN-
GINE MANUAL.”
WARNING: DO NOT
1. DO NOT run engine in an enclosed area.
Exhaust gases contain carbon monoxide, an
odorless and deadly poison.
2. DO NOT place hands or feet near moving
or rotating parts.
3. DO NOT store, spill or use gasoline near
an open flame, or devices such as a stove,
furnace, or water heater which use a pilot
light or devices which can create a spark.
4. DO NOT refuel indoors where area is not
well ventilated. Outdoor refueling is recom-
mended.
5. DO NOT fill fuel tank while engine is
running. Allow engine to cool for 2 minutes
before refueling. Store fuel in approved
safety containers.
6. DO NOT remove fuel tank cap while
engine is running.
7. DO NOT operate engine when smell of
gasoline is present or other explosive
conditions exist.
8. DO NOT operate engine if gasoline is
spilled. Move machine away from the spill
and avoid creating any ignition until the
gasoline has evaporated.
9. DO NOT transport unit with fuel in tank.
10. DO NOT smoke when filling fuel tank.
11. DO NOT choke carburetor to stop
engine. Whenever possible, gradually
reduce engine speed before stopping.
12. DO NOT run engine at excessive
speeds. This may result in injury & /or
damage to unit.
13. DO NOT tamper with governor springs,
governor links or other parts which may
change the governed engine speed.
14. DO NOT tamper with the engine speed
selected by the engine manufacturer.
15. DO NOT check for spark with spark plug
or spark plug wire removed. Use an
approved tester.
16. DO NOT crank engine with spark plug
removed. If engine is flooded, place throttle
in “FAST” position and crank until engine
starts.
17. DO NOT strike flywheel with a hard
object or metal tool as this may cause
flywheel to shatter in operation. Use proper
tools to service engine.
18. DO NOT operate engine without a
muffler. Inspect periodically and replace, if
necessary. If engine is e uipped with
muffler deflector, inspect periodically and
replace, if necessary, with correct deflector.
19. DO NOT operate engine with an
accumulation of grass, leaves, dirt or other
combustible material in the muffler area.
20. DO NOT use this engine on any forest
covered, brush covered, or grass covered
unimproved land unless a spark arrester is
installed on the muffler. The arrester must
be maintained in effective working order by
the operator. In the State of California the
above is re uired by law (Section 4442 of
the California Public Resources Code).
Other states may have similar laws. Federal
laws apply on federal lands.
21. DO NOT touch hot muffler, cylinder, or
fins because contact may cause burns.
22. DO NOT run engine without air cleaner
or air cleaner cover.
23. DO NOT operate during excessive
vibration!
24. DO NOT leave machine unattended
while in operation.
25. DO NOT park machine on a steep grade
or slope.
WARNING: DO
1. ALWAYS DO remove the wire from the
spark plug when servicing the engine or
e uipment TO PREVENT ACCIDENTAL
STARTING.
2. DO keep cylinder fins and governor
parts free of grass and other debris
which can affect engine speed.
3. DO pull starter cord slowly until resis-
tance is felt. Then pull cord rapidly to avoid
kickback and prevent hand or arm injury.
4. DO examine muffler periodically to be
sure it is functioning effectively. A worn or
leaking muffler should be repaired or
replaced as necessary.
5. DO use fresh gasoline. Stale fuel can
gum carburetor and cause leakage.
6. DO check fuel lines and fittings fre uently
for cracks or leaks. Replace if necessary
7. Follow engine manufacturer operating
and maintenance instructions.
8. Inspect machine and work area before
starting unit.
VIBRATION
VIBRATION LEVELS 3.2 g max.
Vibration levels at the operators handles were
measured in the vertical, lateral, and longitudinal
directions using calibrated vibration test e uipment.
Tests were performed on 09/08/97 under the
conditions listed:
SOUND
5
6
8
7
○○○○○○
SAFETY INSTRUCTIONS
GENERAL SAFETY
ASSEMBLY
CONTROLS
LABELS
OPERATION
MAINTENANCE
PARTS DRAWING & LIST...
TROUBLESHOOTING
WARRANTY PROCEDURE
○○○
○○○○○○○
○○○○○○○○
○○○○○○○○
○○○○
○○
10
16
16
6 - 9
4 - 5
4
3
3
2
TABLE OF CONTENTS
14 - 15
WARNING: The Engine Exhaust from this product contains chemicals known
to the State of California to cause cancer, birth defects or other reproductive harm.
○○ ○○○○○○
Sound tests conducted were in accordance with 2000/14/EEC
and were performed on 2/13/2002 under the conditions listed:
NOTE: Sound power level listed is the highest value for any model in this manual. Please
refer to serial plate on the unit for the sound power level for your model.
101 dB WIND DIRECTION:
HUMIDITY:
TEMPERATURE:
BAROMETRIC PRESSURE:
GENERAL CONDITION:
29.91" Hg (760mm Hg)
31 %
East
10 MPH (16.1 kmh)
85° F (29.4° C)
Sunny
WIND SPEED:
WIND DIRECTION:
HUMIDITY:
TEMPERATURE:
BAROMETRIC PRESSURE: 30.34" Hg (770mm Hg)
29 %
South East
2 MPH (3.2 kmh)
48° F (8.9° C)
Sunny
WIND SPEED:
GENERAL CONDITION:
(PR550 MODEL)
Sound level of 82 dBA at operator position

Part No. 350177 Form No. F021604B
Page 3 of 16
PUT OIL IN ENGINE BEFORE STARTING
Read all safety and operating instructions
before assembling or starting this unit.
Engine
Manual Per
Model
These items should be included in your carton. If
any of these parts are missing, contact your dealer.
ASSEMBLY
PACKING CHECKLIST
GENERAL SAFETY
For your safety and the safety of others, these directions should be followed:
Use of Ear Protection is recommended while
operating this machine.
Use of Eye and Breathing protection is recommended
when using this machine, especially in dry and dusty
conditions.
·DO NOT place hands or feet underneath unit, near debris
outlet or near any moving parts.
·DO NOT start engine without height adjust lever in up
position and clutch bail disengaged.
·DO NOT start or operate machine with guards removed.
·DO NOT perform any service on the unit without removing
the spark plug wire.
·DO NOT operate a machine that exhibits excessive vibration.
·DO NOT operate this machine on slopes greater than19°.
·DO NOT use this unit on any surface other than grass lawns.
·DO NOT allow children to operate this e uipment.
-DO read all maintenance and operating instructions before begining
work.
-DO read all engine manufacturers operating and maintenance
instructions.
-DO inspect lawn before begining work. Remove all rocks, wire,
string, or other objects that can present a hazard during work prior to
starting.
-DO identify and mark all fixed objects to be avoided during work,
such as sprinkler heads, water valves, buried cables, or clothes line
anchors, etc.
9
1
11
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
Check
Check
Briggs & Stratton
5.5 Intek OHV
Per Model
Honda 5.5 OHV
Your Billy Goat Power Rake is shipped from the factory in one
carton, completely assembled.
1. UNFOLD the upper handle (item 26) and slide handle lock
loops(item 28) into place to secure the upper handle to the lower.
2. CHECK engine oil level and fill to proper level with engine manufac-
turers recommended grade of oil. Move height adjust lever to down
position, to level engine during checking. See engine manufacturers
instruction manual.
3. CONNECT spark plug wire.
Literature
Assembly
35 11
Wearing gloves is recommended while
operating this machine.
Check Owner's
Manual
35 177
Literature PR
Accessories
35 14
Check
Check EU Declaration
of Conformity &
EU Distributor
List 35 139
Check
Warranty
Card 4 972
28
28
26
28
OS55 , OS55 H, & OS6 S
PR55 , PR55 H, & PR6 S

Part No. 350177 Form No. F021604BPage 4 of 16
15 ENGINE LABELS
13 CONTROLS
Set lever to choke position when
starting a cold engine
Set lever to desired engine speed.
Move lever completely to the left to stop
engine
Briggs & Stratton
'
'
'
..
Honda
OIL ALERT
ENGINE STOPS IMMEDIATELY.
WHEN OIL LEVEL LOW,
RUN CHOKE
STOP
B & S ENGINE THROTTLE CONTROLHONDA ENGINE THROTTLE CONTROL
THROTTLE LEVER
FUEL VALVE CHOKE LEVER
RUN CHOKE
ON
OFF
THIS ENGINE EQUIPPEDWITH
LOW OIL SENSOR, IF ENGINEWILL
NOT START, CHECK OIL LEVEL
Read and follow Operating
Instructions before running engine.
Gasoline is flammable. Allow engine
to cool at least 2 minutes before fueling.
Engines emit carbon monoxide,
DO NOT run in enclosed area.

Part No. 350177 Form No. F021604B
These labels should be included on your Power Rake. If any of these labels are damaged, replace them before putting this
equipment into operation. Item and part numbers are given to help in ordering replacement labels.
Label Danger Keep Hands
and eet Away
Item 51 Part No.400424
Label Do Not ill While
Engine Is Hot
Item 50 Part No.400268
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
400268
WARNING
14 INSTRUCTION LABELS
DANGER
810736
Label Danger lying Material
Item 48 Part No.810736
CAUTION
READ OWNERS MANUAL
BEFORE OPERATING
BEFORE STARTING, MAKE SURE:
USE PERSONAL
PROTECTION EQUIPMENT
HEIGHT ADJUST LEVER IS IN UP POSITION.
ALL GUARDS ARE ATTACHED.
USE ONLY A QUALIFIED MECHANICTO SERVICE THIS MACHINE.
INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY
WORN AND DAMAGED PARTS.
CHECK ENGINE OIL DAILY .
PROPERLY SECURE EQUIPMENT BEFORETRANSPORTING.
DISCONNECT SPARK PLUG WIRE BEFORE SERVICING UNIT.
1
2
3
4
5
BLADE DEPTH
FOR PREVENTATIVE MAINTENANCE
INSPECT AND CLEAN ENGINE AIR FILTER
DAILY. REPLACE AS NEEDED.
GREASE REEL BEARINGS AND LUBRICATE DEPTH
CONTROL LEVER EVERY ENGINE OIL CHANGE.
ALWAYS:
6
ROTATE KNOB TO ADJUST BLADE DEPTH-
BLADES UP
TRANSPORT POSITION BLADES DOWN
OPERATING POSITION
PROTECT BYSTANDERS
FLYING DEBRIS
BLADES UP
BLADES DOWN
350176
WARNING
900327
Label Danger Guard
Item 52 Part No.900327
PULLTO ENGAGE CLUTCH
RELEASETO DISENGAGE CLUTCH
830503
Label Clutch Item 49
Part No.830503
LAWN PREPARATION:
- MOW LAWN TO LOWEST SETTING ON YOUR MOWER.
- DO NOT WATER PRIOR TO SEEDING.
- POWER RAKE TO DETHATCH LAWN AND REMOVE THATCH.
- FERTILIZE LAWN WITH BROADCAST SPREADER.
SEED APPLICATION CHART:
THESE SETTINGS ARE APPROXIMATE GUIDELINES. SEEDING RATES ARE SPEED DEPENDENT.
FASTER TRAVEL DELIVERS LESS SEED.
SEEDING RECOMMENDATIONS:
- FOR BEST RESULTS OVERSEED IN TWO PASSES OF ONE-HALF
APPLICATION RATE AT RIGHT ANGLES OR IN A CRISS-CROSS PATTERN.
- WATER HEAVILY IMMEDIATELY THEN LIGHTLY FOR 10 - 14 DAYS
KEEPING SOIL MOIST.
- AFTER GERMINATION WATER LESS OFTEN TO PROMOTE GROWTH.
SEED
TYPE
RYEGRASS
BLUEGRASS
FESCUE
RATE
LBS
1 000 FT
1/2
3/4
1 1/2
2 1/3
3/4
1
1 1/2
2 1/2
3/4
1 1/4
2
3 1/2
STOP
SETTING
1
2
3
4
3
4
5
6
5
6
7
8
SEED
TYPE
BENTGRASS
BERMUDAGRASS
(HULLED & ZOYSIA)
CENTIPEDEGRASS
(COATED)
ST. AUGUSTINE
GRASS
RATE
LBS
1 000 FT
2/3
1 1/3
3/4
1 2/3
2/3
1 1/4
2 1/2
3/4
1
1 1/3
1 1/2
STOP
SETTING
1
2
1
2
1
2
3
3
4
5
6
BILLY
GOAT
SEEDER
SETTING
5
6
7
8
9
SCOTTS
SEEDER
SETTING
6 1/3
8
10
15 1/2
17
3
1
026
57
4
- PULL BACK ON THE KNOB THEN
SLIDE THE BRACKET TO DESIRED
STOP SETTING.
EXAMPLE: STOP SETTING IS ON 4
- IF SLICING WITHOUT DROPPING
SEEDS FOR LONG PERIOD OF TIME
THEN SET THE STOP SETTING TO
ZERO.
KNOB
BRACKET
STOP
SETTING
2 2 REFERENCE
CHART
(ALL DROP
SEEDER
MODELS)
Label Instructions Seeder Box
Item 45 Part No. 350288
Label Instructions Height Adjust
Item 35 Part No. 350176
Page 5 of 16

Part No. 350177 Form No. F021604B
This unit is e uipped with a folding upper handle for easier storage
and transportation. The handle can be folded by sliding the handle
lock loops(item 28) up. This releases the upper handle, allowing it to
be folded over the unit.
FOLDING HANDLE
This unit re uires two people to lift it. With the handle in
the folded position, lift holding the lower handle and belt/
shaft guard one on each side of the machine. Secure
the machine in place during transport.
HANDLING & TRANSPORTING
Page 6 of 16
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
Engine must be level when checking and filling oil and
gasoline.
ENGINE SPEED: Controlled by throttle lever on the engine.
Under normal conditions, operate at full throttle to accom-
plish your task.
FUEL VALVE: Move fuel valve to "ON" position (Honda
only).
CHOKE: Operated with lever on the engine.
THROTTLE: Move throttle control on engine to fast position.
Pull starting rope to start engine.
IF YOUR UNIT FAILS TO START:
See Troubleshooting on page 12.
INTENDED USE: This machine is designed for removing
thatch from your lawn, renovation of existing lawns, and to
assist in overseeding operations. The machine should not
be used for any other purpose than that stated above.
Inspect machine work area and machine before operat-
ing. Make sure that all operators of this equipment are
trained in general machine use and safety.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check for
damaged or worn reel, loose pulley bolts or set screws, loose
engine or lodged foreign objects. (See trouble shooting
section on page 12).
16 Operation
STARTING ENGINE
Like all mechanical tools, reasonable care must
be used when operating machine.
The blades can be raised or lowered into the ground by
height adjusment lever on the engine base. The height
adjuster lock lever must be pushed back against the
adjustment lever in order to lower the blades into the
ground. The resulting blade depth can be adjusted higher
or lower.
See ADJUSTING BLADE DEPTH.
BLADE POSITION & DEPTH CONTROL LEVER
Clockwise:
To lower
blades
Counter Clockwise:
To raise blades
ADJUSTING BLADE DEPTH
The depth of the blades can be raised or lowered by
rotating the knob on the top of the adjustment lever. The
blades are lowered by rotating the knob clockwise, and
raised by rotating the knob counter-clockwise. The
relative depth of the blades can be gauged by using the
depth scale located on the right front corner of the engine
base. With new blades installed the depth can be
estimated as follows: 2.5 on the scale is even with the
ground, 3 is e ual to 0.25" deep, and 3.5 is e ual to 0.5"
deep
BLADES UP
TRANSPORT
BLADES DOWN
RUNNING
BLADES UP
TRANSPORT

Part No. 350177 Form No. F021604B
RAKING/SLICING TIPS
Before begining, it is best to evaluate the condition of
the lawn by cutting one or more core samples from
area to be treated. A core can be cut using a piece of
pvc, or metal pipe. Hammer the pipe into the ground,
remove it, push the core out of the pipe and inspect it
to determine the depth of thatch in your yard.
THATCH: Thatch is a dense layer of dead grass,
clippings, and roots that builds up over time at the
base of of the lawn preventing air, water, and fertilizer
from reaching the soil. This can cause shallow root
development and make a lawn more susceptible to
drought and disease. Thatch also provides an ideal
environment for insects to hide and multiply. Periodic
removal of thatch will keep your lawn in good health.
HEAVY THATCH: Lawns with an excessive amount of
thatch will re uire multiple treatments for effective
removal. Trying to remove excessive thatch (greater
than 3/4"[19 mm] deep) in one treatment will damage
or destroy the living part of the lawn. It is best to
remove heavy thatch in seasonal treatments (i.e.
spring, and fall).
SLOPES: Rake slopes across not up and down. This
is much easier and safer for the operator and is better
for the lawn. Raking across will help to reduce runoff
during watering and allow the sloped ground to hold
more seed, fertilizer, and water. The units maximum
operating slope is 35% or 19°.
DEPTH: The wide range of depth adjusment on your
unit is provided to allow for blade wear. Setting the
reel deeper will not produce better, or uicker results.
The flail reel is intended to be set so it just touches the
surface on flat ground. The slicing reel should be set
even with the ground for verti-slicing work, and set to a
maximum 1/2" depth for overseeding jobs. Setting the
reel deeper than this will only result in premature wear
on the unit (i.e. failed belt). If you desire to work the
ground deeper than the above guidlines allow, it
should be done gradually in multiple passes..
SLICING / OVERSEEDING: Mow the lawn to shorter
than the normal cut height before starting (i.e. approxi-
mately 2" tall for fescue grass). For the best result,
Slice/Overseed in criss cross pattern (See Fig. 1 and
See Fig 2).
Hints!
RAKING OPERATION
MOW: Mow the lawn to it's normal cut height.
DRY: Be sure grass is dry. Wet conditions can cause
increased damage to healthy grass.
SET DEPTH: With engine off, set the raking depth so that
the blades just touch on a flat surface (i.e. driveway, or
sidewalk).
START ENGINE: See page 5 for further instruction.
ENGAGE BLADES: Pull back on the bail on the opera-
tors handle. NOTE: When engaging the blades in heavy
load conditions (i.e. heavy thatch, or very uneven turf),
push down on the operators handle lifting the front
wheels slightly. Engage the blades. Slowly lower the unit
into the turf.
RAKE: Rake a small test area and examine the results.
Thatch should be removed and deposited on top of the
healthy grass. If excessive damage occurs to healty
grass, adjust the blade depth to decrease damage.
Continue raking the yard, working in one direction (i.e.
north-south, or east-west). NOTE: If a large drop in
engine RPM occurs, or the unit pulls you forward and
bounces during operation the blade depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be
deposited over the top of the lawn. This thatch must be
removed prior to any fertilizing, seeding, or watering of
the lawn. We suggest the use of a lawn vacuum or
wheeled blower for collection and removal of the thatch.
DO NOT- Use this machine on any surface other than a
lawn.
DO NOT- Use this machine on slopes in excess of19°.
DO NOT- Allow persons unfamiliar with this e uipment to
operate it.
DO NOT- Allow children to operate this e uipment.
Fig. 1
Page 7 of 16
Fig. 2
NOTE: Must have the flail reel assembly (35 112) for
this operation.
OPERATION continued
16

Part No. 350177 Form No. F021604B
OPERATION continued
16
MOW: Mow the lawn to shorter than the normal cut height
(approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause in-
creased damage to healty grass.
SET DEPTH: With engine off, set the raking depth so that the
blades just touch on a flat surface (i.e. driveway, or sidewalk).
START ENGINE: See Page 5.
ENGAGE BLADES: Pull back on the bail on the operators
handle. NOTE: When engaging the blades in heavy load
conditions (i.e. heavy thatch, or very uneven turf), push down
on the operators handle lifting the front wheels slightly.
Engage the blades. Slowly lower the unit into the turf.
SLICE: Verti-cut a small test area and examine the results.
Some thatch and cut stems should be removed and deposited
on top of the healthy grass. Grass runners should be cut and
ready for removal. If excessive damage occurs to healthy
grass, adjust the blade depth to decrease damage. Continue
raking the yard, working in one direction (i.e. north-south, or
east-west). NOTE: If a large drop in engine RPM occurs, or
the unit pulls you forward and bounces during operation the
blade depth is set too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of
thatch and cut stems will be deposited over the top of the lawn.
We suggest the use of a lawn vacuum or wheeled blower for
collection and removal of the thatch/stems.
DO NOT- Use this machine on any surface other than a
lawn.
DO NOT- Use this machine on slopes in excess of 19°.
DO NOT- Allow persons unfamiliar with this e uipment to
operate it.
DO NOT- Allow children to operate this e uipment.
OVERSEEDING OPERATION
MOW: Mow the lawn to shorter than the normal cut
height (approximately 2" tall)
DRY: Be sure grass is dry. Wet conditions can cause
increased damage to healthy grass.
SEED: Spread grass seed according to the seed
suppliers directions (e.g. 10 lbs. per 1000 ft2 [4.5 kg. per
93 m2 ])
SET DEPTH: With engine off, set the raking depth so
that the blades reach 1/4"-1/2"(6-12 mm) below a flat
surface (i.e. driveway, or sidewalk).
START ENGINE: See Page 5.
ENGAGE CLUTCH: Pull back on the bail on the
operators handle. NOTE: When engaging the clutch in
heavy load conditions (i.e. heavy thatch, or very
uneven turf), push down on the operators handle lifting
the front wheels slightly. Engage the clutch. Slowly
lower the unit into the turf.
DO NOT- Use this machine on any surface other than a
lawn.
DO NOT- Use this machine on slopes in excess of 19°.
DO NOT- Allow persons unfamiliar with this e uipment to
operate it.
DO NOT- Allow children to operate this e uipment.
SLICE: Run machine over the area that has been
seeded to incorporate the seed into the soil. If exces-
sive damage occurs to healthy grass, adjust the blade
depth to decrease damage. Continue raking the yard,
working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or the unit
pulls you forward and bounces during operation the
blade depth is set too low.
WATER/FERTILIZE: After the seed has been worked
into the soil, water and fertilize according to the seed
suppliers directions.
VERTI-CUTTING OPERATION
NOTE: Must have the slicing reel assembly (35 113) for
this operation.
NOTE: Must have the slicing reel assembly (35 113) for
this operation.
Page 8 of 16

Part No. 350177 Form No. F021604B
Page 9 of 16
ADJUSTING SEED RATE
LAWN PREPARATION
LAWN PREPARATION
1
1
STOP
SETTING
1
THESE SETTINGS ARE APPROXIMATE GUIDELINES. SEEDING RATES ARE SPEED DEPENDENT.
FESCUE
3 1/2
3/4
1 1/4
261 1/2
33/4
1
1 1/3 4
5
8
GRASS
5
6
7
ST. AUGUSTINE
FASTER TRAVEL DELIVERS LESS SEED.
1,000 FT
BLUEGRASS
RYEGRASS
SEED
TYPE
3/4
1 1/2
2 1/2
1
3/4
2 1/3
1 1/2
1/2
RATE
LBS
21 1/3
21 1/4
2 1/2 3
2
1 2/3
2/3
3/4
2
1,000 FT
2/3
LBS
RATE
2
5
6
4
3
4
3
SEED
TYPE
STOP
SETTING
2
1
BERMUDAGRASS
(HULLED & ZOYSIA)
CENTIPEDEGRASS
(COATED)
BENTGRASS
15 1/2
17
8
9
6 1/3
10
8
(ALL DROP
SEEDER
MODELS)
BILLY
5
7
6
GOAT
SEEDER
SETTING
REFERENCE
CHART
SETTING
SEEDER
SCOTTS
SEED APPLICATION CHART:
OPERATION continued
16
- MOW LAWN TO LOWEST SETTING ON YOUR MOWER.
- DO NOT WATER PRIOR TO SEEDING.
- POWER RAKE TO DETHATCH LAWN AND REMOVE
THATCH.
- FERTILIZE LAWN WITH BROADCAST SPREADER.
-FOR BEST RESULTSOVERSEED IN TWOPASSES OF
ONE-HALF
APPLICATION RATE AT RIGHT ANGLES OR IN A CRISS-
CROSSPATTERN.
- WATER HEAVILY IMMEDIATELY THEN LIGHTLY FOR 10 -
14 DAYS
KEEPING SOIL MOIST.
- AFTER GERMINATION, WATER LESS OFTEN TO
PROMOTEGROWTH.
- PULL BACK ON THE KNOB THEN
SLIDE THE BRACKET TO DESIRED
STOP SETTING.
EXAMPLE: STOP SETTING IS ON 4
- IF SLICING WITHOUT DROPPING
SEEDS FOR LONG PERIOD THEN SET
THE STOP SETTING TO ZERO . OF
TIME.
STOP
SETTING BRACKET KNOB
DROPPING SEEDS
- AFTER ADJUSTING THE STOP SETTING, LIFT UP ON THE BAR TO OPEN
THEDROP SEEDERDOOR.
- TO STOP DROPPING SEEDS, PUSH FORWARD ON THE HANDLE TO
CLOSE THE DROP SEEDER DOOR.
NOTE: IF SLICING WITHOUT DROPPING SEEDS FOR LONG PERIOD OF
TIME THEN SET THE STOP SETTING TO ZERO .

Part No. 350177 Form No. F021604B
Page 10 of 16
MAINTENANCE
BLADE WEAR AND ROTATING REEL END TO END
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or
cracked blades. Measure the overall length of the blade. (See fig. 1)
5. If blades measure less than 3.25"(83 mm) in overall length they
must be replaced. NOTE: We recommend replacing all the flails at
once.
FLAIL BLADE WEAR
Use only a qualified mechanic for
any adjustments, disassembly or
any kind of repair .
DISCONNECT SPARK PLUG WIRE
BEFORE SERVICING UNIT.
WARNING: TO AVOID PERSONAL INJURY, ALWAYS
TURN MACHINE OFF, MAKE SURE ALL MOVING
PARTS COME TO A COMPLETE STOP.
RECONNECT SPARK PLUG WIRE,
AND ALL GUARDS, BEFORE
STARTING ENGINE.
ENGINE: See engine manufacturer
operator's instructions.
17
Engine (See Engine Manual)
Check engine oil
Inspect and clean engine air filter
Grease reel bearings
Inspect belt
Maintenance Operation
Follow these hourly
maintenance intervals.
Maintenance Schedule
Every
25 hrs
Every Use
(Daily)
ROTATING FLAIL REEL END TO END
USE ONLY BILLY GOAT ORIGINAL
EQUIPMENT PARTS FOR
REPLACEMENT AND REPAIR
NOTE: Takes approx. 10 min. and re uires 1/2" socket wrench with
extension.
1. Wait for engine to cool and disconnect spark plug.
2 . Remove (3) lock nuts(item 62) holding the belt guard(item 21) in
place. It is necessary to lower the height adjust lever to reach the
locknuts on the guard. Remove the guard.
3. Remove the belt(item 9) by rotating the reel pulley(item 2) and
walking it out of the groove. Discard old belt
4. Install new belt using same procedure to walk the belt into the
groove.
5. With new belt installed pull bail rod back to engaged position and
measure extension of idler spring. Spring should stretch 3/4" - 1" (19
25 mm) with bail engaged. Adjust clutch cable as necessary to achieve
this extension.
6. Re-install the belt guard.
DRIVE BELT REPLACEMENT
Inspect for loose, worn,
or damaged parts
Oil height adjustment linkage
To maximize flail blade life and performance the reel can be rotated
end to end periodically to provide a fresh lead cutting edge. Takes
approx. 20 min. and re uires 1/2" and 9/16" socket wrenches with
extension bar.
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Remove (6) lock nuts(item 62) holding the belt and shaft guards(item
21 &22) in place. It is necessary to lower the height adjust lever to reach
the locknuts on the guards. Remove the guards.
5. Remove the drive belt(item 9) by "walking" it out of the groove on the
reel pulley(item 2).
6. Remove the (4) lock nuts(item 60) and washers(item 68) holding the
bearings(item 23) to the frame of the unit.
7. The reel is now free from the machine. Slide the reel down and out of
the machine.
8. Remove the capscrew(item 71), lockwasher(item 57), reel pulley(item
2), key(item 42), and reel spacer(item 10) from the end of the reel.
9. Rotate the reel end to end, and re-install these items on the opposite
end of the reel.
1 . Re-install the reel in reverse order of removal. Re-install the guards
in reverse order of removal.
Fig. 1
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or
cracked blades. Measure the overall length of the blade from the center
of the attachment bolt to the tip of the worn blade.
5. If blades measure less than 3"(76 mm) in length they must be
replaced. NOTE: We recommend replacing all the blades at once.
SLICING BLADE WEAR

Part No. 350177 Form No. F021604B
POWER RAKE SEEDER BOX KIT P/N 350281
Page 11 of 16
PARTS LIST
ITEM NO. PART NO. DESCRIPTION QTY
1 350287 BOX DROP SEEDER WA 1
2 350306 BRACKETADJ DROP SEEDER ASSY 1
3 350276 BAR DOOR LINKGAGE 1
4 350270 SHAFT DROP SEEDER 1
5 350271 PLATE DOOR DROP SEEDER 1
6 350272 PLATE DOOR DROP SEEDER END 1
7 350273 PLATE DOOR DROP SEEDER ARM 1
8 350274 BRACKETLID SEEDER BOX 1
9 350275 COVER CLEAR PLASTIC 19.5 X3 1
10 8171003 WASHER 5/16 FLAT CUT 1
11 900321 BEARING CLIP 1.375 OD 4
12 510144 PLATE MOUNT FLAPPER 2
13 400217 SPRING TENSION 2
14 8024040 BOLT CARRAIGE 5/16 - 18 X 1 1
15 8024021 BOLT CARRAIGE 1/4 - 20 X 3/4" 6
16 350286 SCREW SHEET METAL 4
17 8160001 NUT LOCK 1/4 6
18 8160007 NUT LOCK 5/8 - 11 2
19 8160002 NUT LOCK 5/16 1
21 8172015 WASHER 3/4 SAE 4
22 350280 WASHER 0.906 OD X 0.656 ID 8
24 350310 RUBBER PAD 1/8" TK x 1/2" W 2
PARTS BAG SEEDER BOX KIT
19 8160002 NUT LOCK 5/16 (REQUIRE ON THE OLD MODELS ONLY) 4
20 8177011 WASHER LOCK 5/16 4
23 8041026 SCREWCAP 5/16-18 x 3/4 4
- 350283 LIT SEEDER BOX (INCLUDES TEMPLATE) 1

Part No. 350177 Form No. F021604B
Page 12 of 16
FLAIL REEL ASSY 35 112
FLAIL SHAFT KIT 35 185 FLAIL BLADE KIT 35 186
item PARTS PR500 QTY
no. LIST Part No.
73 SHAFT FLAIL BLADE 350141 4
74 BLADEFLAIL 350100 52
75 SPACERBUMPER5/8" x 1/4" 350143 4
76 SPACERBUMPER5/8" x 1/2" 350144 44
77 SHAFT WA FLAIL REEL 350145 1
78 CLIPLOCK 1/2" 350146 8
79 WASHER 1/2 SAE 8172011 8
item PARTS Part No. QTY
no. LIST
73 SHAFT FLAIL BLADE 350141 4
78 CLIPLOCK 1/2" 350146 8
item PARTS Part No. QTY
no. LIST
74 BLADE FLAIL 350100 52
78 CLIP LOCK 1/2" 350146 8

Part No. 350177 Form No. F021604B
Page 13 of 16
SLICING REEL ASSY 35 113
SLICING BLADE KIT 35 187
item PARTS PR500 QTY
no. LIST Part No.
81 BLADESLICING REEL 350147 20
85 SCREWCAP1/4-20 x 3/4, GR. 5 350151 40
86 NUT LOCK 1/4-20 8142004 40
SPACER BUMPER KIT 35 258
item PARTS PR500 QTY
no. LIST Part No.
75 SPACER BUMPER5/8" x 1/4" 350143 4
76 SPACER BUMPER5/8" x 1/2" 350144 44
item PARTS PR500 QTY
no. LIST Part No.
57 LOCK WASHER5/16 TWISTEDTOOTH 800177 1
71 SCREWCAP5/16 - 24 x 1" HCS GR. 5 400164 1
80 SHAFT SLICING WA 350142 1
81 BLADESLICING REEL 350147 20
82 PLATEBLADEMTG. 350148 20
83 SPACER BLADEMTG. 350149 10
84 SPACER BLADEASSY 350150 9
85 SCREWCAP1/4-20 x 3/4, GR. 5 350151 40
86 NUT LOCK 1/4-20 8142004 40
87 COLLARSPACER 350152 1
88 WASHER0.937 x 1.750 x 0.119 350153 1
89 WASHERLOCK 7/8 INT. TOOTH 350154 1
90 NUT JAM 7/8-14 350155 1

Part No. 350177 Form No. F021604B
PR55 , PR55 V, PR55 H PR55 HV, OS55 , OS55 H
Page 14 of 16
18 PARTS DRAWING

Part No. 350177 Form No. F021604B
Page 15 of 16
item PARTS PR550 QTY PR550H QTY OS550
PR550V QTY OS550H PR550HV QTY
no. LIST Part No. Part No. Part No. Part No.
1 Pulley 3" OD 350101-01 1 350101 1 350101-01 1 350101 1
2 Pulley 6.5" OD X ¾" 350102 1 350102 1 350102 1 350102 1
3 Wheel8" Front PR 350103 2 350103 2 350103 2 350103 2
4 Wheel10" Front PR 350104 2 350104 2 350104 2 350104 2
5 Height Adjust Assy 350107 1 350107 1 350107 1 350107 1
6 Reel Flail / Slicing Assy 350112 1 350112 1 350113 1 350113 1
7 Pulley Idler 2.75" 350114 1 350114 1 350114 1 350114 1
8 Arm Idler WA 350115 1 350115 1 350115 1 350115 1
9 Belt 5L X 36 350116 1 350116 1 350116 1 350116 1
10 Spacer Reel Pulley 350118 1 350118 1 350118 1 350118 1
11 Bracket Mount Clutch Cable 350119 1 350119 1 350119 1 350119 1
12 Chassis WA W/ Label 350194 1 350194 1 350194 1 350194 1
13 Frame Front WA 350121 1 350121 1 350121 1 350121 1
14 Bushing 0.375 OD X 0.256 IDX 0.88 350309 1 350309 1 350309 1 350309 1
15 Spring Height Adjust PR500 350125 1 350125 1 350125 1 350125 1
16 Link Height Adjust PR500 350126 1 350126 1 350126 1 350126 1
17 Yoke ½ - 20 350127 1 350127 1 350127 1 350127 1
18 Pin Yoke ½" 350128 1 350128 1 350128 1 350128 1
19 Bracket Mount Hgt. Adj. WA 350182 1 350182 1 350182 1 350182 1
20 Spacer Spanner Wheel PR500 350130 4 350130 4 350130 4 350130 4
21 Guard Belt WA W/ Label 350195 1 350195 1 350195 1 350195 1
22 Guard Shaft WA W/ Label 350196 1 350196 1 350196 1 350196 1
23 Bearing ¾" Cast Pillow Block 350133 2 350133 2 350133 2 350133 2
24 Handle Lower LH WA 350134 1 350134 1 350134 1 350134 1
25 Handle Lower RH WA 350135 1 350135 1 350135 1 350135 1
26 Handle Upper PR500 350136 1 350136 1 350136 1 350136 1
27 Bail Clutch WA 350137 1 350137 1 350137 1 350137 1
28 Loop Folding Handle 350138 2 350138 2 350138 2 350138 2
29 Deflector Rubber 350167 1 350167 1 350167 1 350167 1
30 Shield Bearing 350168 2 350168 2 350168 2 350168 2
31 Bar Clamp Deflector 350171 1 350171 1 350171 1 350171 1
32 Bracket Height Adjust Lock WA 350173 1 350173 1 350173 1 350173 1
33 Guard Pulley Back 350184 1 350174 1 350184 1 350174 1
34 Lever Height Control 350175 1 350175 1 350175 1 350175 1
35 Label Instr. Hgt. Adj. 350176 1 350176 1 350176 1 350176 1
36 Bolt Shoulder ¼" x 1 ¾" 350178 1 350178 1 350178 1 350178 1
37 Bolt Shoulder 5/16" x 1 ¾" 350179 1 350179 1 350179 1 350179 1
38 Cable Clutch Reel PR500 350181 1 350181 1 350181 1 350181 1
39 Spring Extension 400217 1 400217 1 400217 1 400217 1
40 Bolt Shoulder 1/2" X 1" 500114 3 500114 3 500114 3 500114 3
41 ENGINEHONDA 5.5 H.P. GX160 - - 600115 1 - - 600115 1
ENGINE INTEK 5.5HPOHV B&S 350197 1 - - 350197 1 - -
42 KEY 3/16" X 1" 9201078 1 9201078 2 9201078 1 9201078 2
42A KEY 1/4" x 1" 9201113 1 - - 9201113 1 - -
43 GRIP 1" x 13" 400570 2 400570 2 400570 2 400570 2
44 GRIP LEVER 1/8 x 1 x 5" 500181 1 500181 1 500181 1 500181 1
45LABELINSTRUCTIONSEEDERBOX----35028813502881
46 WASHER 5/16 FC (BELT GUARD) 8171003 2 - - 8171003 2 - -
47 LABEL GOAT HEAD 850209 1 850209 1 850209 1 850209 1
48 LABEL DANGERTHROWN OBJECT 810736 1 810736 1 810736 1 810736 1
49 LABEL CLUTCH VQ 830503 1 830503 1 830503 1 830503 1
50 LABEL HOT ENGINE 400268 1 400268 1 400268 1 400268 1
51 LABEL WARNING 400424 2 400424 2 400424 2 400424 2
52 LABEL DANGERGUARD 900327 1 900327 1 900327 1 900327 1
53 PLUG CAP1" RD 890132 2 890132 2 890132 2 890132 2
54 BOLT CARRAIGE3/8-16 x 1 3/4 8024061 4 8024061 4 8024061 4 8024061 4
55 BOLT CARRAIGE5/16-18 x 1 3/4 8024043 2 8024043 2 8024043 2 8024043 2
56 BOLT CARRIAGE5/16 -18 x 3/4 8024039 4 8024039 4 8024039 4 8024039 4
57 LOCK WASHER TW. TOOTH 400502 1 400502 1 800177 1 800177 1
58 NUT LOCK #10-24 8164005 1 8164005 1 8164005 1 8164005 1
59 NUT LOCK 1/4-20 8160001 2 8160001 2 8160001 8 8160001 8
60 NUT LOCK 3/8-16 8160003 9 8160003 9 8160003 9 8160003 9
item PARTS PR550 QTY PR550H QTY OS550
PR550V QTY OS550H
PR550HV QTY
no. LIST Part No. Part No. Part No. Part No.
61 NUT LOCK 3/8-16 THIN 8161042 3 8161042 3 8161042 3 8161042 3
62 NUT LOCK 5/16-18 8160002 18 8160002 18 8160002 19 8160002 19
63 SCREWCAP1/4-20 x 1 1/2 8041008 1 8041008 1 8041008 1 8041008 1
64 SCREWCAP3/8 - 16 x 1 1/4 8041051 1 8041051 1 8041051 1 8041051 1
65 SCREWCAP5/16-24 x 1" GR.5 8042026 3 8042026 3 8042026 3 8042026 3
66 SCREWCAP5/16 - 18 x 1 1/2 8041030 4 8041030 4 8041030 4 8041030 4
67 WASHER 5/16 FLATCUT 8171003 4 8171003 4 8171003 5 8171003 5
68 WASHER 3/8 FLATCUT 8171004 8 8171004 8 8171004 8 8171004 8
69 WASHER 1/2 FLATCUT 8171006 2 8171006 2 8171006 2 8171006 2
70 NUT LOCK 1/2 - 13 8160005 4 8160005 4 8160005 4 8160005 4
71 SCREWCAPREEL PULLEY 8041050 1 8041050 1 400164 1 400164 1
72BUTTONSOCKET5/16-18X5/8”35026643502664----
FLAIL REEL ASSEM BLY (FOR PR550 AND PR550H MODELS ONLY)
73SHAFTFLAILBLADE 35014143501414----
74BLADEFLAIL 3501005235010052----
75SPACERBUMPER5/8"x1/4" 35014343501434----
76SPACERBUMPER5/8"x1/2" 3501444435014444----
77SHAFTWAFLAILREEL 35014513501451----
78CLIPLOCK1/2" 35014683501468----
79WASHER1/2SAE 8172011881720118----
SLICING REEL ASSEM BLY (FOR PR550V, PR550HV, OS550, AND OS550HMODELS ONLY)
80 SHAFT SLICING WA 350142 1 350142 1 350142 1 350142 1
81 BLADESLICING REEL 350147 20 350147 20 350147 20 350147 20
82 PLATE BLADEMTG. 350148 20 350148 20 350148 20 350148 20
83 SPACER BLADEMTG. 350149 10 350149 10 350149 10 350149 10
84 SPACER BLADEASSY 350150 9 350150 9 350150 9 350150 9
85 SCREWCAP1/4-20 x 3/4, GR. 5 350151 40 350151 40 350151 40 350151 40
86 NUT LOCK 1/4-20 8142004 40 8142004 40 8142004 40 8142004 40
87 COLLAR SPACER 350152 1 350152 1 350152 1 350152 1
88 WASHER 0.937 x 1.750 x 0.119 350153 1 350153 1 350153 1 350153 1
89 WASHER LOCK 7/8 INT. TOOTH 350154 1 350154 1 350154 1 350154 1
90 NUT JAM 7/8-14 350155 1 350155 1 350155 1 350155 1
SEEDER BOX ASSEMBLY (FOR OS550, ANDOS550HMODELS ONLY)
91BOXDROPSEEDERWA ----35028713502871
92 BRACKET ADJ DROP SEEDERASS
Y
----35030613503061
93BARDOORLINKGAGE ----35027613502761
94SHAFTDROPSEEDER ----35027013502701
95PLATEDOORDROPSEEDER ----35027113502711
96PLATEDOORDROPSEEDEREND----35027213502721
97PLATEDOORDROPSEEDERARM----35027313502731
98BRACKETLIDSEEDERBOX ----35027413502741
99COVERCLEARPLASTIC19.5X3 ----35027513502751
100WASHERLOCK5/16 ----8177011481770114
101BEARINGCLIP1.375OD ----90032149003214
102PLATEMOUNTFLAPPER ----51014425101442
103SPRINGTENSION ----40021724002172
104BOLTCARRAIGE5/16-18X1 ----8024040180240401
105BOLTCARRAIGE1/4-20X3/4" ----8024021680240216
106SCREWSHEETMETAL ----35028643502864
107NUTLOCK5/8-11 ----8160007281600072
108WASHER3/4SAE ----8172015481720154
109WASHER0.906ODX0.656ID ----35028083502808
110SCREWCAP5/16-18x3/4 ----8041026480410264
111RUBBERPAD1/8"TKX1/2"WX3"----35031023503102

Part No. 350177 Form No. F021604B
Page 16 of 16
TROUBLESHOOTING Before Requesting Service Review These Suggestions
Engine stalls or labors when raking. Raise blades so that they just touch the ground on a
level surface.
SolutionPossible Cause
Problem
Blades set too deep into ground
2
Abnormal vibration.
Engine will not start.
Engine is locked, will not
pull over.
Debris locked against reel, or drive pulleys. Engine
problem.
Check stop switches, throttle, choke position and
gasoline. Connect spark plug wire. Clean or replace
air cleaner. Contact a ualified service person.
Stop work immediately. Replace any damaged or
missing blades. Tighten all loose bolts and nuts.
Damaged or missing blades. Loose handle bolts.
Loose engine bolts
Stop switch off (Honda only). Throttle in off position.
Engine not in full choke position. Out of gasoline. Bad
or old gasoline. Spark Plug wire disconnected. Dirty air
cleaner. Engine oil level too low (Honda only).
Pull spark plug wire and remove debris. Contact an
engine servicing dealer for engine problems.
MODEL NO.
GENERAL ENGINE SPECIFICATIONS
HORSEPOWER
ENGINE
BRIGGS &
STRATTON
HONDA 5.5
5.5 11 4 2 191E1
GX16 K1QX
GOVERNED RPM
37
36
ENGINE
When servicing engine refer to specific manufacturers engine
owner's manual. All engine warranty is covered by the specific
engine manufacturer. If your engine re uires warranty or other
repair work contact your local servicing engine dealer. When
contacting a dealer for service it is a good idea to have your engine
model number available for reference(See table page above). If
you can not locate a servicing dealer in your area you can contact
the manufacturers national service organization.
To reach:
Briggs & Stratton: 800-233-3723
American Honda: 800-426-7701
Subaru America: 800-277-6246
Never store engine indoors or in enclosed poorly ventilated
areas with fuel in tank, where fuel fumes may reach an open flame,
spark or pilot light, as on a furnace, water heater, clothes dryer or
other gas appliance.
If engine is to be unused for 3 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent
gum deposits from forming on these parts and causing possible
malfunction of engine. Drain fuel outdoors, into an approved
container, away from open flame. Be sure engine is cool. Do not
smoke. Run engine until fuel tank is empty and engine runs out of
gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing
the formation of fuel gum deposits during storage. Add stabilizer to gasoline in
fuel tank or storage container. Always follow mix ratio found on stabilizer
container. Run engine at least 10 min. after adding stabilizer to allow it to reach
the carburetor.
UNIT STORAGE
SUBARU 6. EX17 D5 2 36
Engine Service and Warranty
Contact your nearest engine manufacturer's
authorized servicing dealer. (See page 7)
22.1 22
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON / LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: [phone] FAX: [phone] www.billygoat.com
WARRANTY PROCEDURE
Purchased
from
Purchase
Date
21 Serial Plate Record your machine model, serial number
and date-of-purchase and where purchased
R
min-1
1803 S. Jefferson
Lee's Summit,
MO 64062 / USA
Tel [phone]
Fax [phone]
Model SerialNo.
Unit(Weight) EnginePower
lbs. kg kW rpm
R
99 dB
Should a Billy Goat Machine fail due to a defect in material and/or
workmanship, the owner should make a warranty claim as follows:
-The Machine must be taken to the dealer from whom it was purchased
or to an authorized Servicing Billy Goat Dealer.
-The owner must present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
-The Warranty Claim will be completed by the authorized Billy Goat
Dealer and submitted to their respective Billy Goat Distributor for their
territory. Attention: Service Manager. Any parts replaced under
warranty must be tagged and retained for 90 days.
-The distributor service manager will sign off on the claim and submit
it to Billy Goat for consideration.
-The Technical Service Department at Billy Goat will study the claim
and may request parts to be returned for examination. Billy Goat will
notify their conclusions to the distributor service manager from whom
the claim was received.
-The decision by the Quality / Service department at Billy Goat to
approve or reject a Warranty claim is final and binding.
Note: To process a Warranty Claim, it is necessary to quote the Model & Serial
Number which are printed on the Billy Goat Serial Plate (See owner’s manual).