Billy Goat PR550 User manual

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 1 350412_E_HI
Patent 6253416 and other patents pending
POWER RAKE AND OVERSEEDER Owner's Manual
PR550, PR550H, OS552, OS552H
Beginning Serial #: 020316001
Accessories Replacement Parts
Original Instructions
IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE
SLICING REEL
A complete verti-
slicing reel for your
PR. 20" wide reel for
use in grasses that
require vertical
cutting, and for
assisting in lawn
overseeding projects.
P/N 350602
OVERSEEDER KIT
The new light weight Plastic Overseeding
Kit is constructed of durable High Density
Polypropylene with two lift handles on
each side to assist in lifting the entire unit
and easily converts a PR Series Power
Rake into an overseeder with 4 bolts and
minimal tools.
NOTE: Overseeder Conversion Kit
(350328) includes Slicing Reel (350602).
Part No. (350325) comes with the
Overseeder Box only.
P/N 350325 / 350328
SLICING BLADES
A full set of blades for
replacement. Includes
new lock washers for
replacement
installation.
P/N 350187
FLAIL SHAFTS
A full set of shafts
for replacement.
Includes new lock
clips for
replacement
installation.
P/N 350185
FLAIL BLADES
A complete set of
our high quality flail
blades for your PR.
Includes new lock
clips for
replacement
installation.
P/N 350186
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
2
CONTENTS
SPECIFICATIONS AND SAFETY 3
INSTRUCTION LABELS 4
PACKING CHECKLIST & ASSEMBLY 5
OPERATION 6-8
MAINTENANCE 9-10
TROUBLESHOOTING 10
ILLUSTRATED PARTS LIST 11-16
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
3
SPECIFICATIONS
PR550 PR550H OS552 OS552H
Engine: HP
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
5.5 (4.1 kW)
Engine: Model
13L1320111F8
X160UT2QX2
13L1320111F8
X160UT2QX2
Engine: Type
B&S
VANGUARD
HONDA OHV
B&S
VANGUARD
HONDA OHV
Engine: Fuel Capacity
3.0 qt. (2.84 L)
3.88 qt. (3.6 L)
3.0 qt. (2.84 L)
3.88 qt. (3.6 L)
Engine: Oil Capacity
0.66 qt. (0.62 L)
0.69 qt. (0.65 L)
0.66 qt. (0.62 L)
0.69 qt. (0.65 L)
Total Unit Weight:
149# (67.7 kg)
147# (66.8 kg)
162# (73.6 kg)
160# (72.7 kg)
Engine weight:
34# (15.4 kg)
34# (15.4 kg)
36# (16.3 kg)
34# (15.4 kg)
Max. operating slope
15o
20o
15o
15o
SAFETY
WARNING
This product can expose you to chemicals including gasoline engine exhaust, which is known to the State
of California to cause cancer, and carbon monoxide, which is known to the State of California to cause
birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
4
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT®Power Rake/Overseeder. If any labels are damaged or missing,
replace them before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for
convenience in ordering replacement labels. The correct position for each label may be determined by referring to the Figure and
Item numbers shown.
LABEL DANGER KEEP HANDS LABEL CLUTCH ITEM #49 DANGER FLYING DEBRIS LABEL SPARK ARREST
AND FEET AWAY P/N 830503 ITEM # 48 P/N 810736 ITEM #81 100252
ITEM #51 P/N 400424
LABEL CAUTION GUARDS LABEL EXPLOSIVE FUEL LABEL INSTRUCTION HEIGHT ADJ.
ITEM #52 P/N 900327 ITEM # 50 P/N 400268 ITEM #35 P/N 350176
LABEL INSTRUCTIONS SEEDER BOX LABEL SEED METERING
ITEM #30 P/N 350386 ITEM #29 P/N 350392
(page 8) (page 8)
ENGINE LABELS
ENGINE CONTROLS
Honda Briggs & Stratton Set lever to choke when starting cold
Throttle lever
Set lever to desired engine speed.
Fuel valve Choke lever Move lever completely to the left to
stop engine
BRIGGS & STRATTON HONDA
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
5
PACKING CHECKLIST
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-16.
Your Billy Goat Power Rake is shipped from the factory in one carton, completely assembled.
PUT OIL IN ENGINE BEFORE STARTING
ASSEMBLY
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box, the Handle Assembly is attached to the unit by
cables.
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts lists on pages 11-16.
1. UNFOLD the upper handle (item 26) and slide handle lock loops (item 28) into place to secure the upper handle to the
lower.
2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move height adjust
lever to down position, to level engine during checking. See engine manufacturer’s instruction manual.
3. CONNECT spark plug wire.
Boxing Parts Checklist
Briggs & Stratton
5.5 B&S VANGUARD
Honda 5.5 OHV
Subaru 6HP EX17
Literature Assy
P/N-350110
PARTS BAG & LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-350412, General Safety and Warnings Manual P/N-100295, Declaration of
Conformity P/N-350139.
PR550, PR550H,
PR550T, PR550HT,
PR600S
OS552, OS552H,
and OS602S
28
26 28
28
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
6
OPERATION
NOTE: Items in ( ) can be referenced in the Parts Illustration and Parts list on pages 11-16.
SLICING OPERATION
NOTE: NEVER PARK THIS UNIT ON A SLOPE OF ANY KIND. Always keep the reel in
the up position when parking the unit.
BLADE POSITION & DEPTH CONTROL LEVER: The blades can be raised or lowered into the
ground by height adjustment lever on the engine base. The height adjuster lock lever must be
pushed back against the adjustment lever in order to lower the blades into the ground. The
resulting blade depth can be adjusted higher or lower.
ADJUSTING BLADE DEPTH: The blades can be raised or lowered by rotating the knob on the
top of the adjustment lever. The blades are lowered by rotating the knob clockwise, and raised
by rotating the knob counter-clockwise. The relative depth of the blades can be gauged by using
the depth scale located on the right front corner of the engine base. With new blades installed
the depth can be estimated as follows: 2.5 on the scale is even with the ground, 3is equal to
0.25" deep, and 3.5 is equal to 0.5" deep.
FOLDING HANDLE: This unit is equipped with a folding upper handle for easier storage and
transportation. The handle can be folded by sliding the handle lock loops (item 28) up. This
releases the upper handle, allowing it to be folded over the unit.
RAKING OPERATION-FLAIL REEL (See Fig. 4)
NOTE: Must have the flail reel assembly (350112) for this operation.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface (i.e.
driveway, or sidewalk).
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the blades
in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle
lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the turf.
RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on
top of the healthy grass. If excessive damage occurs to healthy grass, adjust the blade depth to
decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE:If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during
operation the blade depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This
thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use
of a lawn vacuum or wheeled blower for collection and removal of the thatch.
clockwise to
lower blades
counter clockwise
to raise blades
blades up
transport blades up
transport
blades down
running
Fig. 1
Fig. 2
SPRING TINE CONVERSION
If you are converting your Power Rake to a spring tine reel, you will
need to replace the spacer on the control lever to accommodate for
the tine. First remove the clip (item 18), then unscrew the yoke (item
17), remove the washer (items 69) and insert the spacer (item 75) in
front of the spring. Reassemble in reverse order.
Fig. 3
Fig. 4
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
7
RAKING OPERATION-SPRING REEL (See Fig. 5)
NOTE:Must have the spring tine reel assembly (350354) for this operation.
SET DEPTH: With engine off, set the raking depth so that the spring tines are just above touching the
flat surface (i.e. driveway, or sidewalk) the units height is being adjusted on. NOTE: Allowing the
spring tines to have substantial contact with the ground will cause premature wear and failure of the
spring tines.
ENGAGE TINES: Pull back on the bail on the operators handle. NOTE: When engaging the spring
tines in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators
handle lifting the front wheels slightly. Engage the spring tines. Slowly lower the unit into the turf.
RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on
top of the healthy grass. If excessive damage occurs to healthy grass, adjust the spring tine depth to
decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during
operation the spring tine depth is set too low.
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This
thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use
of a lawn vacuum or wheeled blower for collection and removal of the thatch.
VERTI-CUTTING OPERATION (See Fig. 6)
NOTE:Must have the slicing reel assembly (350602) for this operation.
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface
(i.e. driveway, or sidewalk).
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the
turf.
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should be
removed and deposited on top of the healthy grass. Grass runners should be cut and ready for
removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease
damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE:
If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation
the blade depth is set too low.
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited
over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection
and removal of the thatch/stems.
OVERSEEDING OPERATION
NOTE:Must have the slicing reel assembly (350602) for this operation.
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft2[4.5 kg. per 93 m2])
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm) below a flat surface (i.e. driveway,
or sidewalk).
ENGAGE CLUTCH: Pull back on the bail on the operators handle. NOTE: When engaging the clutch in heavy load conditions (i.e.
heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the clutch. Slowly
lower the unit into the turf.
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If excessive damage occurs to
healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or
east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation the blade
depth is set too low.
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to the seed suppliers directions.
Fig. 5
Fig. 6
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
8
ADJUSTING SEED RATE
LAWN PREPARATION
Mow lawn to lowest setting on your mower.
Do not water prior to seeding.
Power rake to dethatch lawn and remove thatch.
Fertilize lawn with broadcast spreader.
For best results overseed in two passes of one-half application
rate each, at right angles or in a criss-cross pattern. (See Fig 7 &
8)
Water heavily immediately then lightly for 10 - 14 days, keeping
soil moist.
After germination, water less often to promote root growth.
*****TIPS*****
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core samples from area to be treated. A core can
be cut using a piece of PVC, or metal pipe. Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to
determine the depth of thatch in your yard.
MOW
Mow the lawn to its normal cut height. Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.
INSPECT
Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can present a hazard during work
IDENTIFY
Mark all fixed objects to be avoided during work, such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc.
THATCH
Thatch is a dense layer of dead grass, clippings, and roots that builds up over time at the base of the lawn preventing air, water, and
fertilizer from reaching the soil. This can cause shallow root development and make a lawn more susceptible to drought and disease.
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of thatch will keep your lawn in good health.
HEAVY THATCH
Lawns with an excessive amount of thatch will require multiple treatments for effective removal. Trying to remove excessive thatch
(greater than 3/4"[19 mm] deep) in one treatment will damage or destroy the living part of the lawn. It is best to remove heavy thatch in
seasonal treatments (i.e. spring, and fall).
SLOPES
Rake slopes across not up and down the slope. This is much easier and safer for the operator and is better for the lawn. Raking across
will help to reduce runoff during watering and allow the sloped ground to hold more seed, fertilizer, and water. The units maximum
operating slope is 35% or 19°.
DEPTH
The wide range of depth adjustment on your unit is provided to allow for blade wear. Setting the reel deeper will not produce better
results. The flail reel is intended to be set so it just touches the surface on flat ground. The slicing reel should be set even with the ground
for verti-slicing work, and set to a maximum 1/2" depth for overseeding. Setting the reel deeper will only result in premature wear on the
unit (i.e. failed belt). If you desire to work the ground deeper than the above guidelines, it should be done gradually in multiple passes.
SLICING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before starting (i.e. approximately 2" tall for fescue grass).
For the best result, Slice/Overseed in criss-cross pattern (See Fig. 7 & 8).
Fig. 7
Fig. 8
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
9
MAINTENANCE
NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 11-16.
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use (daily)
Every 25 Hours
Inspect for loose, worn or damaged parts

Check engine oil

Inspect belt

Engine (See Engine Manual)
Grease reel bearings

Inspect and clean engine air filter

Oil height adjustment linkage

FLAIL BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Securely gain access to the underside of the machine.
4. Inspect blades for wear, and immediately replace any bent or cracked blades.
Measure the overall length of the blade. (See Fig. 9)
5. If blades measure less than 3.25"(83 mm) in overall length they must be
replaced. NOTE: We recommend replacing all the flails at once.
SLICING BLADE WEAR
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the overall length of the blade
from the center of the attachment bolt to the tip of the worn blade.
5. If blades measure less than 3"(76 mm) in length they must be replaced. NOTE: We recommend replacing all the blades
at once.
ROTATING FLAIL REEL END TO END
To maximize flail blade life and performance the reel can be rotated end to end periodically to provide a fresh lead cutting edge.
Takes approx. 20 min. and requires 1/2" and 9/16" socket wrenches with extension bar.
1. Wait for engine to cool and disconnect spark plug.
2. Close fuel valve on engine (if available).
3. Lean unit back onto lower handles and secure in place.
4. Remove seven lock nuts (item 62 & 40) holding the belt and shaft guards (item 21 & 22) in place. It is necessary to lower
the height adjust lever to reach the locknuts on the guards. Remove the guards.
5. Remove the drive belt (item 9) by "walking" it out of the groove on the reel pulley (item 2).
6. Remove the four lock nuts (item 60) and washers (item 68) holding the bearings (item 23) to the frame of the unit.
7. The reel is now free from the machine. Slide the reel down and out of the machine.
8. Remove the capscrew (item 71), lock washer (item 57), reel pulley (item 2), key (item 42), and reel spacer (item 10) from
the end of the reel.
9. Rotate the reel end to end, and re-install these items on the opposite end of the reel.
10. Re-install the reel in reverse order of removal. Re-install the guards in reverse order of removal.
Fig. 9
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
10
TROUBLESHOOTING
DRIVE BELT REPLACEMENT
NOTE: Takes approx. 10 min. and requires 1/2" socket wrench with extension.
1. Wait for engine to cool and disconnect spark plug.
2. Remove four lock nuts (item 62) holding the belt guard (item 21) in place. It is necessary to lower the height adjust lever to
reach the locknuts on the guard. Remove the guard.
3. Remove the belt (item 9) by rotating the reel pulley (item 2) and walking it out of the groove. Discard the old belt.
4. Install new belt using same procedure to walk the belt into the groove.
5. With new belt installed pull bail rod back to engaged position and measure extension of idler spring. Spring should stretch
3/4" - 1" (19 25 mm) with bail engaged. Adjust clutch cable as necessary to achieve this extension.
6. Re-install the belt guard.
Problem Possible Cause Solution
Abnormal vibration
Damaged or missing blades. Loose
handle bolts. Loose engine bolts.
Stop work immediately. Replace any
damaged or missing blades. Tighten
all loose nuts and bolts.
Engine stalls or labors
when raking
Blades set too deep into ground.
Raise blades so that theyjust touch
the ground on a level surface.
Engine will not start
Stop switch off(Honda only). Throttle
in off position.
Check choke position.
Out of gasoline or bad, old gasoline. Check gasoline.
Spark Plug wire disconnected. Connect spark plug wire.
Gas valve off. Turn on gas valve.
Dirtyair cleaner.
Clean or replace air cleaner. Contact
a qualified service person.
Engine is locked, will not
pull over
Debris locked against reel, or drive
pulleys. Engine problem.
Pull spark plug wire and remove
debris. Contact an engine servicing
dealer for engine problems.
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
11
POWER RAKE SEEDER BOX KIT P/N 350395
PARTS LIST
ITEM NO. PART NO. DESCRIPTION QTY
1350366 BOX AND LID ASSEMBLY 1
2350390 BRACKET CABLE MOUNTING 1
3350385 CABLE SEED METERING ASSY 1
4350378 SHAFT PLASTIC DROP SEEDER 1
5350271 PLATE DOOR DROP SEEDER 1
6350272 PLATE DOOR DROP SEEDER END 1
7350387 PLATE DOOR DROP SEEDER END ARM 1
9350370 PULLEY 3V GROOVE 0.625" BORE 1
10 8172009 WASHER #10 3/8 SAE 1
11 900321 BEARING CLIP 1.375 OD 4
12 890108 KNOB WING 5/16-18 1
13 400217 SPRING TENSION 2
14 8024040 BOLT CARRIAGE 5/16 - 18 X1 1
15 8024021 BOLT CARRIAGE 1/4-20 X 3/4" 1
16 8123087 SCREW SELF TAP #10-24 X3/8" HMS ZP 4
17 8160001 NUT LOCK 1/4 1
18 350389 BRACKET CABLE SEEDER BOX 1
19 8160002 NUT LOCK 5/16 1
20 8177011 WASHER LOCK 5/16 4
21 350369 PULLEY 3V GROOVE 1.530" BORE 1
22 350280 WASHER 0.906 O.D. X 0.656 I.D. X0.062 7-8
ITEM NO. PART NO. DESCRIPTION QTY
23 8041026 SCREWCAP 5/16-18 x 3/4 4
24 350372 BELTO-RING 5/16 X15 9/16" 1
25 8197031 PIN COTTER 1/8" X1" 1
26 9195106 ROLL PIN 1/8 - 1 1/4 1
27 8172020 WASHER 5/16 FENDER 4
28 8172007 WASHER 1/4 SAE 3
29 350392 LABEL SEED METERING 1
30 350386 LABEL DROP SEEDER BOX 1
31 900230 WASHER 1/2 FC 2
32 8161044 NUT LOCK 1/2" THIN HGT 1
33 890456 LABEL HOSE PLUG KD/SV 1
34 350423 LABEL OS BADGING 1
35 8024061 CARRIAGE BOLT 3/8-16 X1 3/4" 1
36 8024025 CARRIAGE BOLT 1/4-20 X1 3/4" 1
37 350399 PIN CLEVIS .25 X.61 1
38 900471 PIN HAIR 1/4 ZP 1
39 8160003 NUT LOCK 3/8-16 HEX 1
40 8171004 WASHER 3/8 FC 2
41 350391 BRACKETMOUNTING METERING SEED 1
42 8059135 SCREW MACHINE #10-24 X5/8 1
43 8164005 NUT LOCK LT #10-24 HEX 1
44 900407 TY-WRAP 1
32
31
21
24
30
23
20
9
22 11
6
33
1
17
5
28
27
34
16
13
426
43
17
28
40
39
1942
12
10
29
41
36
14
3
44
15
28
35
25
38
11
722
37
2
18
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
12
FLAIL SHAFT KIT 350185
FLAIL BLADE KIT 350186
SPACER BUMPER KIT 350258
SLICING BLADE KIT 350187
FLAIL REEL KIT P/N 350112-S
item
PARTS
Part No. QTY
no. LIST
73 SHAFT FLAIL BLADE 350141 4
78 CLIP LOCK 1/2" 350146 8
item
PARTS
Part No. QTY
no. LIST
74 BLADE FLAIL 350100 30
78 CLIP LOCK 1/2" 350146 8
item PARTS QTY
no. LIST Part No.
57 LOCK WASHER 3/8 S/T MED 8177012 1
68 WASHER 3/8 FLAT CUT 8171004 1
71 SCREWCAP REEL PULLEY 8041050 1
73 SHAFT FLAIL BLADE 350141 4
74 BLADE FLAIL 350100 30
76 SPACER BUMPER 5/8" x 1/2" 350144 54
77 SHAFT WA FLAIL REEL 350145 1
78 CLIP LOCK 1/2" 350146 8
79 WASHER 1/2 SAE 8172011 8
item PARTS LIST QTY
no. Part No.
81 BLADE10" HEX SLICING 350147 20
85 SCREWCAP1/4-20 X 3/4 GR8 350427 40
86 NUTLOCK 1/4-20 8142004 40
item
PARTS
QTY
no.
LIST
76 SPACERBUMPER5/8" x 1/2" 350144 54
Part No.
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
13
SPRING TINE REEL ASSY - 350355-S
SPRING REPLACEMENT KIT - 350356-S
SLICING REEL ASSY P/N 350602
item PARTS QTY
no. LIST
1 SHAFT WA SPRING TINEREEL 350353 1
2 SHAFT SPRING TINEREEL 350351 4
3 SPRING TINE 350352 108
4 RING RETAINING 1/2" 350146 8
5 SCREWCAP3/8"-16 X 1" HCS ZP 8041050 1
6 WASHERLOCK 3/8 S/T MED 8177012 1
68 WASHER3/8 FLAT CUT 8171004 1
Part No.
item
PARTS
no.
LIST
3 SPRINGTINE 350352 108
4 RING RETAINING 1/2" 350146 8
Part No.
QTY
Item PARTS PR500 QTY
No. LIST Part No.
57 WSHR-STL, BLV, .386" X 1.063" X .082" MZ 8181012 1
71 SCREWCAP 3/8"-16 X 1" HCS ZP 8041050 1
80 SHAFT SLICING WA 350142 1
81 BLADE SLICING REEL 350147 20
82 PLATE BLADE MTG. 350148 20
83 SPACER BLADE MTG. 350149 10
84 SPACER, REEL PM 350443 9
85 SCREWCAP 1/4-20 x 3/4, HCS ZP 8041004 40
86 NUT LOCK 1/4-20 8142004 40
87 SPACER, HARDENED REEL OS900SP 351297 1
88 WASHER 0.937 x 1.750 x 0.119 350153 1
89 WASHER LOCK 7/8 INT. TOOTH 350154 1
90 NUT JAM 7/8-14 350155 1
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
14
PARTS DRAWING PR/OS
PR550, PR550H, OS552, OS552H
LEFT FRONT WHEEL
ASSY. FOR
THE OS MODELS ONLY
SEE PAGE 11
FOR PARTS LIST
SEE PAGE 12 FOR FLAIL REELPARTS LIST
SEE PAGE 13 FOR SLICING REEL PARTS LIST
SEE PAGE 13 FOR SPRING REEL PARTSLIST
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
15
PARTS LIST PR/OS
Item PARTS
PR550 QTY PR550H QTY OS552 QTY OS552H QTY
no. LIST Part No. Part No. Part No. Part No.
1 PULLEYPR550/0S550 350440 1350440 1350440 1350440 1
1A Spacer 5/8 OD X3/8 ID X1.0 LG 350401 3350401 3350401 3350401 3
2 Pulley6.5" OD X¾" 350102 1350102 1350102 1350102 1
3 WHEEL 8.0" X 5/8" BEARING 350103 2350103 2350103 2350103 2
4 WHEEL 10.0" X5/8" BEARING 350104 2350104 2350104 2350104 2
5 HT ADJ ASSY PR 350107-S 1 350107-S 1 350107-S 1 350107-S 1
6 Reel Flail / Slicing / Spring Assy 350112 1350112 1350336 1350336 1
7 PulleyIdler 2.75" 350114 1350114 1350114 1350114 1
8 Arm Idler WA 350115 1350115 1350115 1350115 1
9 Belt 5L X 36 350116 1350116 1350116 1350116 1
10 Screwcap 5/16" x24 x1 1/2 Gr5 HCS 8042030 18042030 18042030 18042030 1
11 Bracket Mount Clutch Cable 350119 1350119 1350119 1350119 1
12 Chassis WAW/ Label 350194 1350194 1350194 1350194 1
13 Frame Front WA 350121 1350121 1350121 1350121 1
14 Bushing 0.375 OD X0.256 ID X0.88 350309 1350309 1350309 1350309 1
15 Spring Height Adjust PR500 350125 1350125 1350125 1350125 1
16 Link Height Adjust PR500 350126 1350126 1350126 1350126 1
17 Yoke ½ - 20 350127 1350127 1350127 1350127 1
18 Pin Yoke ½" 350128 1350128 1350128 1350128 1
19 Bracket Mount Hgt. Adj. WA 350182 1350182 1350182 1350182 1
20 Spacer Spanner Wheel PR500 350130 4350130 4350130 4350130 4
21 GUARD, BELT W/LABELS OS/PR 350384-S 1 350384-S 1 350384-S 1 350384-S 1
22 GUARD SHAFT WAW/LABELS 350196-S 1 350196-S 1 350196-S 1 350196-S 1
23 Bearing ¾" Cast Pillow Block 350133 2350133 2350133 2350133 2
24 Handle Lower LH WA 350134 1350134 1350134 1350134 1
25 Handle Lower RH WA 350135 1350135 1350135 1350135 1
26 Handle Upper PR500 350375 1350375 1350375 1350375 1
27 Bail Clutch WA 350374 1350374 1350374 1350374 1
28 Loop Folding Handle 350138 2350138 2350138 2350138 2
29 Deflector Rubber 350167 1350167 1350167 1350167 1
30 Shield Bearing 350168 2350168 2350168 2350168 2
31 Bar Clamp Deflector 350171 1350171 1350171 1350171 1
32 Bracket Height Adjust Lock WA 350173 1350173 1350173 1350173 1
33 Guard PulleyBack 350400 1350400 1350400 1350400 1
34 Lever Height Control 350175 1350175 1350175 1350175 1
35 Label Instr. Hgt. Adj. 350176 1350176 1350176 1350176 1
36 Bolt Shoulder ¼" x 1 ¾" 350178 1350178 1350178 1350178 1
37 Bolt Shoulder 5/16" x 1 ¾" 350179 1350179 1350179 1350179 1
38 Cable Clutch PR 350408-S 1 350408-S 1 350408-S 1 350408-S 1
40 BOLT SHOULDER 1/2" X1" 500114 1500114 1500114 1500114 1
41 ENGINE HONDA 5.5 H.P. GX160 - - 600115 1 - - 600115 1
ENGINE 5.5 HP B&S VANGUARD 350379 1 - - 350379 1 - -
42 KEY3/16" X 1" 9201078 19201078 19201078 19201078 1
43 GRIP 1" x13" 400570 2400570 2400570 2400570 2
44 GRIP LEVER 1/8 x1 x5" 500181 1500181 1500181 1500181 1
45 LABEL INSTRUCTION SEEDER BOX - - - - 350288 1350288 1
46 LABEL PR BADGING 350422 1350422 1350422 1350422 1
47 FINGER BELT WIRE 350301 1350301 1350301 1350301 1
48 LABEL DANGER THROWN OBJECT 810736 1810736 1810736 1810736 1
49 LABEL CLUTCH VQ 830503 1830503 1830503 1830503 1
50 LABEL WARNING FUEL EN/SP 100261 1 - - 100261 1 - -
51 LABEL WARNING 400424 2400424 2400424 2400424 2
52 LABEL DANGER GUARD 900327 1900327 1900327 1900327 1
53 PLUG CAP 1" RD 890132 2890132 2890132 2890132 2
54 BOLT CARRAIGE 3/8-16 x1 3/4 8024061 48024061 48024061 48024061 4
55 BOLT CARRAIGE 5/16-18 x1 3/4 8024043 28024043 28024043 28024043 2
56 BOLT CARRIAGE 5/16 -18 x3/4 8024039 48024039 48024039 58024039 5
57 WASHER LOCK 3/8" S/T MED 8177012 18177012 1 - - - -
WASHER LOCK 5/16" TW TOOTH - - - - 430298 1430298 1
58 NUT LOCK #10-24 8164005 18164005 18164005 18164005 1
59 NUT LOCK 1/4-20 8160001 28160001 28160001 58160001 5
60 NUT LOCK 3/8-16 8160003 12 8160003 12 8160003 12 8160003 12
62 NUT LOCK 5/16-18 8160002 15 8160002 15 8160002 16 8160002 16
63 SCREWCAP 1/4-20 x1 1/2 8041008 18041008 18041008 18041008 1
64 SCREWCAP 3/8 - 16 x1 3/4 8041053 18041053 18041053 18041053 1
NOT FOR REPODUCTION

OVERSEEDER/POWER RAKE Owner’s Manual
Part No 350412 350412_E_HI
16
Item
PARTS
PR550 QTY PR550H QTY OS552 QTY OS552H QTY
no.
LIST
Part No. Part No. Part No. Part No.
65 SCREWCAP 5/16-24 x 3/4" GR.5 8042026 38042026 38042026 38042026 3
65B Washer 5/16 Twist Tooth 430298 1430298 1430298 1430298 1
66 SCREWCAP 5/16 - 18 x 1 1/2 8041030 48041030 48041030 48041030 4
68 WASHER 3/8 FLAT CUT 8171004 98171004 98171004 88171004 8
69 WASHER 1/2 SAE ZP 8172011 28172011 28172011 58172011 5
70 NUT LOCK 1/2" - 13 THIN HGT 8161044 48161044 48161044 48161044 4
71 SCREWCAP 3/8" - 16 X1" HCS ZP 8041050 18041050 18041050 18041050 1
72 BUTTON SOCKET 5/16-18X5/8” 350266 4350266 4 - - - -
73 BOLT SHOULDER 1/2" x 2" 520031 2520031 2520031 2520031 2
74 FLANGE SCREW 0.375 -16 X0.75 791080 2791080 2791080 2791080 2
76 WASHER 3/8 SAE 8172009 28172009 28172009 28172009 2
77 NUT PAL 3/8 360218 2360218 2360218 2360218 2
78 WASHER 1/4 FLAT CUT 8171002 58171002 58171002 58171002 5
79 PIN CLEVIS 3/8" X1.625 520119 2520119 2520119 2520119 2
80 RETAINER 3/8" BOLT PUSH NUT 360279 2360279 2360279 2360279 2
81 LABEL SPARK ARRESTOR EN/SP - - 100256 1 - - 100256 1
82 WASHER 1/4 SAE 8172007 18172007 18172007 18172007 1
83 LABEL LOGO PRODUCT SMCIRCLE 890456 1890456 1890456 1890456 1
90 WASHER 1.125" OD X.344 ID X.25 THK - - - - 441150 1441150 1
100 WASHER FLAT 5/16" 8171003 58171003 58171003 58171003 5
101 SCREW MACH #10-24 X5/8" HWF ZP 8059135 18059135 18059135 18059135 1
102 NUT LOCK #10-24 HEX 8164005 18164005 18164005 18164005 1
104 LABEL MADE IN U.S.A. 520116 1520116 1520116 1520116 1
NOT FOR REPODUCTION