Billy Goat MV650H PUSH User manual

Form No F072111B 9 Part No 840244
MV650H PUSH Vacuum Owner’s Manual
OPERATION
OPERATOR CONTROLS
The operator’s position is at the rear of the machine between the handlebars. The operator should STAND in a position to
allow both handlebars to be grasped firmly, which allows sufficient leverage to steer the machine. Operator’s controls are
shown below.
Operator Control Locations
1 Nozzle Door Adjuster 4 Throttle Control
2 Bag Latch
3 Pull Starter
STARTING
CHECK engine oil level before operating machine.
1. Place equipment on a level, firm surface that is free of rocks or other debris.
2. Place throttle in CHOKE position.
Throttle
DO NOT START equipment without the debris bag in place.
2
3
4
1
engine oil level before operating machine.
1. Place equipment on a leve
l, firm surface that is fr
l, firm surface that is fr
2. Place throttle in CHOKE position.
2. Place throttle in CHOKE position.
Operator Control Locations
Operator Control Locations
1 Nozzle Door Adjuster 4 Throttle Control
1 Nozzle Door Adjuster 4 Throttle Control
2 Bag Latch
2 Bag Latch
3 Pull Starter
3 Pull Starter
3 Pull Starter 3 Pull Starter
engine oil level before operating machine.
engine oil level before operating machine.
1

Part No 840244 10 Form No F072111B
MV650H PUSH Vacuum Owner’s Manual
3. Secure the unit with left hand at the handle then pull starter rope with right hand to start engine.
PULL STARTER CORD slowly until resistance is felt. Then pull cord rapidly to avoid kickback.
4. Move throttle control back to RUN position and allow engine to reach correct operating speed.
VACUUM NOZZLE HEIGHT ADJUSTMENT
FOR MAXIMUM PICKUP: Adjust nozzle height as close to debris as possible, but without blocking airflow into the nozzle.
NOTE: Never bury nozzle into debris. The vacuum nozzle is raised and lowered by turning the crank handle clockwise and
counter-clockwise.
SECURE UNIT AT
THE HANDLE
WITH LEFT HAND
DURING START
PULL ROPE
STARTER WITH
RIGHT HAND
slowly until resistance is felt. Then pull cord rapidly to avoid kickback.
slowly until resistance is felt. Then pull cord rapidly to avoid kickback.
4. Move throttle control back to RUN position and allow engine to reach correct operating speed
4. Move throttle control back to RUN position and allow engine to reach correct operating speed
Adjust nozzle height as close to debris as possible
Adjust nozzle height as close to debris as possible
: Never bury nozzle into debris. The vacuum nozzle is raised and lowered by turning the crank handle clockwise and
: Never bury nozzle into debris. The vacuum nozzle is raised and lowered by turning the crank handle clockwise and

Form No F072111B 11 Part No 840244
MV650H PUSH Vacuum Owner’s Manual
VACUUM NOZZLE DOOR ADJUSTMENT
The vacuum nozzle door adjusts for the maximum performance under various applications.
Nozzle fully opened. This is ideal for turf application
Nozzle half way opened. This is ideal for hard surface application
Nozzle closed for OPTIONAL hose kit. This is ideal TO USE WITH THE HOSE KIT.
Nozzle closed for OPTIONAL hose kit. This
Nozzle closed for OPTIONAL hose kit. This
Nozzle closed for OPTIONAL hose kit. This
eal for hard surface application
eal for hard surface application

Part No 840244 12 Form No F072111B
MV650H PUSH Vacuum Owner’s Manual
VACUUMING OPERATION
This machine is designed for vacuuming leaves, grass clippings, and other types of organic litter.
Debris mixed with cans, bottles, and small amounts of sand can be vacuumed; however, it is not this machine's primary
purpose. Vacuuming cans, bottles, and sand will affect the longevity of your machine. In dusty conditions it maybe
necessary to purchase Felt Bag Kit (P/N 840022).
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for
damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See
parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 22).
SHUT DOWN
1. Pull Throttle Control all the way back to the STOP position.
CLEARING A CLOGGED NOZZLE
DISCONNECT spark plug wire before servicing unit.
1. Shut engine off and wait for impeller to stop completely.
2. Disconnect spark plug wire.
3. Wearing durable gloves, remove clog.
WEAR durable gloves. Clog may contain sharp materials.
4. Reconnect spark plug wire.
DEBRIS BAG
Debris bags are normal replaceable wear items.
Frequently empty debris to prevent bag overloading with more weight than you can lift.
Bag liners are available for use in various conditions where debris will be vacuumed. (see Bag Liner Options shown on
page 1).
DO NOT place bag on or near hot surface, such as engine.
Be sure engine has come to a complete stop before removing or emptying bag!!.
Many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. However,
following these rules will help maintain your machine's ability to vacuum in dusty conditions:
•Run machine at idle to quarter throttle.
•Machine or pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before
use.
Having one or more spare bags (840189) is a good way to reduce down time while dirty bags are being cleaned.
Felt Bag (840194) accessory is great when used in dusty conditions.
Hint!
DO NOT place bag on or near hot surface
DO NOT place bag on or near hot surface
Many vacuums are used where dust is mixed with trash. Y
Many vacuums are used where dust is mixed with trash. Y
following these rules will help maintain your machine's ability to vacuum in dusty conditions:
following these rules will help maintain your machine's ability to vacuum in dusty conditions:
•Run machine at idle to quarter throttle.
•Run machine at idle to quarter throttle.
•Machine or pressure-wash debris bag if normal cleaning does
Debris bags are normal replaceable wear items.
Frequently empty debris to prevent bag overload
Frequently empty debris to prevent bag overload
Bag liners are available for use in various conditions where debris will be vacuumed. (see Bag Liner Options shown on
Bag liners are available for use in various conditions where debris will be vacuumed. (see Bag Liner Options shown on
DO NOT place bag on or near hot surface
shut engine off immediately and check for
key, loose engine or lodged foreign objects. Note: See
spark plug wire before servicing unit.
spark plug wire before servicing unit.
durable gloves. Clog may contain sharp materials.
durable gloves. Clog may contain sharp materials.
Debris bags are normal replaceable wear items.
Debris bags are normal replaceable wear items.
Frequently empty debris to prevent bag overload