Billyoh EZE BASE User manual

‘ EZE BASE’ INSTRUCTIONS
BillyOh.com – Grassthorpe Road – Sutton on Trent – Newark – Nottinghamshire – NG23 QX – Tel. [phone]
THE BILLYOH EZE BASE
*Tape measure not included.
BUILDING ASSEMBLY
STEP BY STEP CONSTRUCTION OF YOUR PRESSURE TREATED EZE BASE
STEP 1: MEASURING YOUR SHED PRIOR TO ASSEMBLY OF ‘EZE BASE’
Measure the length of the building which is to be mounted on the Eze Base and transfer these dimensions to the
two outers supplied. Mark accordingly and trial fit with the floor of the building.
STEP 2: LAYING OUT ALL PARTS
Lay all parts of the Eze Base in their intended place as
demonstrated by the illustration (right). This is to ensure that
the stretchers can be placed equally apart as to support a
building most effectively and to check that all parts have been
received.
‘L’ bracket
Corner
anchors
Stretchers
Outer

‘ EZE BASE’ INSTRUCTIONS
BillyOh.com – Grassthorpe Road – Sutton on Trent – Newark – Nottinghamshire – NG23 QX – Tel. [phone]
STEP 3: NAILING OUTERS AND STRETCHERS TOGETHER
Nail through the outers into either end of the other stretchers. This is the
strongest way of securing the structure and the easiest. To further strengthen
the structure it is recommended that each stretcher end be nailed in two
equally spaced positions.
STEP 4: SQUARING OFF THE FRAMING
Measure across the diagonals, checking that both
measurements match, ensuring that the frame is now
square.
STEP 5: SCREWING ‘L’ BRACKETS ONTO FRAME (OPTIONAL)
If the ground you wish to place your Eze Base and building on is not level then it is
necessary to add the ‘L’ brackets provided to level out the Eze Base. Throughout
this STEP use a spirit level to assess progress. Screw the ‘L’ brackets where
required from the inside of the outer framing. Bear in mind you may not need to
use all the brackets.
NOTE: Any pare ‘L’ bracket can be u ed to trengthen the corner (refer to OPTIONAL STEP 7).
STEP 6: SCREWING THE CORNER ANCHORS TO THE CORNERS AND FIXING IN PLACE
Screw the four corner anchors to each inner corner of the base framing ensuring the
anchors are flush with the top of the base frame. Then drive the Eze Base into the
ground to the desired height ensuring the base is level (use spirit level).
Once fixed in position it is recommended that you pack any gaps beneath the Eze
Base and ground. This will help to protect the base from weathering and create a
neater finish.

‘ EZE BASE’ INSTRUCTIONS
BillyOh.com – Grassthorpe Road – Sutton on Trent – Newark – Nottinghamshire – NG23 QX – Tel. [phone]
OPTIONAL STEP 7: SCREWING ANY REMAINING ’L’ BRACKETS TO THE
OUTER CORNERS OF THE BASE
If you have remaining ‘L’ brackets these can be used to further strengthen
the Eze Base by screwing to the outer corners.
Now your Eze Base is completed you are ready to assemble your building
on top.
CONGRATULATIONS YOUR NEW
IS FINISHED!
BILLYOH.COM
PRODUCT WARRANTY
All BillyOh.com products are built to the highest quality standards and should provide convenient, secure
storage for years to come, this of course being subject to reasonable use, care and transportation.
In the event of a manufacturing defect becoming evident in the first year from the time of purchase,
BillyOh.com will ensure that the product will be repaired or replaced at no extra charge if the product is
returned to the authorised dealer from whom it was purchased.
All products from which a warranty claim is made must be received at BillyOh.com with freight pre-paid and
accompanied with sufficient proof of purchase. These must be pre-authorised with BillyOh.com
If in doubt about the product’s limitations, please read and understand all of the instructions and guidance
notes, if necessary contact BillyOh.com before returning.
PLEASE NOTE: The warranty does not extend to damage caused by post-purchase transportation, careless
handling nor damage caused by misuse. PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE.
EZE BASE
EZE BASEEZE BASE
EZE BASE