FRAME IT ALL 300000400 User manual

300000400, 300000075, 300000434, 300000450,
300001400, 300001075, 300001434, 300001450,
300003400, 300003075, 300003434, 300003450,
300004400, 300004075, 300004434, 300004450
RAISED GARDEN BED
4’ x 12’
Layout your timbers along the borderline and connect each
timber together by inserting the top of the stake through the
bracket loops with the stake pointing to the sky. This enables
you to freely position your border to get your desired location.
Customer Service: 1800-914-9835 |
[email protected]m
© Frame It All. All Rights Reserved.
1 LEVEL KIT CONTAINS:
•Composite timbers 4’ x 8
•Stacking Brackets x 16
•Stacking Stakes x 8
•Plugs x 32
•Caps x 8
ASSEMBLY INSTRUCTIONS –For the first level
STEP 1:
Assemble the timbers by sliding one end of timber into channel end
of one of the brackets. Use plugs to cover the holes on both sides to
lock the bracket in place.
Repeat this process on the opposite end of the timber flipping the bracket in the opposite
direction (see image). Repeat for all timbers on the
First level.
STEP 2:
Layout the base level of your raised using 8 x 4’ timbers. Insert stake through the hole of
the bracket and into each of the corners to lock all sides in place.
FOR INDOOR & HARD SURFACE:
If you plan to assemble raised bed on a hard surface, use
hacksaw to remove the spike of each stake. Use these cut
down stakes for the base level only of your raised garden.
Trim stake spike with
hacksawfor use indoor
or on hard surfaces
1 LEVEL
STEP 2a: For one level, add caps to each of the
top corner joints to finish off the raised garden.
HAPPY GARDENING!
ASSEMBLY INSTRUCTIONS –For Product with Two to Four Levels
How the Joints Work
Use plugs (included)
to cover the holes on
both side of timbers
Use plugs to
cover the holes
–two plugs are
required per
bracket (1 on
each side)
Use a Capto
complete the
top level.
Use stacking
stakes for
ground level
frames and
stacking
additional levels.
Use stacking
stake when
creating a
multi-level
Stacking stake fit
into the tops other
Stacking stakes
3-Way Connection:
Combining one half of a
4-way bracket and a
stacking bracket (A),will
result in a 3-way
junction (B).
2 LEVEL KIT CONTAINS:
•Composite timbers 4’ x 18
•Stacking Brackets x 28
•4-way Brackets x 8
•Stacking Stakes x 16
•Plugs x 72
•Caps x 8
3 LEVEL KIT CONTAINS:
•Composite timbers 4’ x 26
•Stacking Brackets x 34
•4-way Brackets x 8
•Stacking Stakes x 24
•Plugs x 104
•Caps x 8
3 LEVEL KIT CONTAINS:
•Composite timbers 4’ x 36
•Stacking Brackets x 56
•4-way Brackets x 16
•Stacking Stakes x 32
•Plugs x 144
•Caps x 8
STEP 3:
For the second level, connect 4 timbers with a
stacking bracket on one end and a mid-section 4-
way bracket on the other end in alternating
orientation.
Then, connect 2 timbers with top 4-way brackets on
both ends in alternating orientation as shown to the
right. These 3 timbers will be used to install the
cross timber.
Now connect 4 timbers with stacking brackets on
both ends as you did for the first level.
4 x
2 x
4 x
A
B
C

STEP 4:
Layout the timbers for the second level flat on the ground while referencing
the diagram below. Place the cross timbers for level 2 on top of the upside
stakes to ensure it will fit. Once adjustments have been made, the stakes can
be hammered into the ground and the second level can be stacked.
A
BC
STEP 5:
Connect 8 timbers for level 3 with stacking brackets on both ends
and stack them as you did for level 1.
4 x cross
timbers on a
4-level design
2 x cross timber
for a 3-level
design.
3 LEVELS
4 LEVELS
Note: Stacking stakes insert into the top of the previous level stakes.
STEP 6:
Connect 10 timbers for level 4 in the same quantity and pattern
as you did for level 2. Stack and connect them in the same way as
well.
C
C
C
B
A
A
A